Operating and installation instructions Refrigerator with Dynamic cooling K 11820 SD K 12620 SD K 12820 SD K 12820 SD edt/cs To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
Contents Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 How to save energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Switching on and off . . . . . . . . . . . . . . .
Contents Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Side-by-side installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Climate range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Ventilation. . . .
Guide to the appliance a On/Off button b Temperature selector button c Temperature display 4 d Super cool button and indicator light e Dynamic cooling button and indicator light
Guide to the appliance a Dynamic cooling fan b Butter and cheese compartment c Egg tray d Adjustable shelves e Bottle rack f Bottle shelf g Condensate channel and drain hole h Fruit and vegetable containers 5
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal, and should be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children.
Warning and Safety instructions This appliance complies with all relevant local and national safety requirements. Improper use can, however, present a risk of both personal injury and material damage. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time. They contain important notes on the installation, safety, operation and care of the appliance.
Warning and Safety instructions Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Do not install and use a damaged appliance. A damaged appliance is dangerous. ~ If the connection cable is faulty it must only be replaced by a service technician authorised by the manufacturer to protect the user from danger. - disconnect from the mains, - air the room in which the appliance is located for several minutes and - contact the Service Department for advice.
Warning and Safety instructions ~ The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and tested regularly, and where there is any doubt, the household wiring system should be inspected by a qualified electrician.
Warning and Safety instructions Correct use ~ Never store explosive materials in the appliance or any products containing propellants (e.g. spray cans). Thermostats switching on may produce sparks which could present a fire hazard. Flammable compounds could explode. ~ Do not operate any electrical equipment (e.g. an electric ice-cream maker) inside the appliance. Danger of sparking and explosion. ~ If storing alcohol with a high percentage proof, make sure it is tightly closed and stored upright.
Warning and Safety instructions Stainless steel appliances ~ Do not use sticky notes, transparent adhesive tape, masking tape or other types of adhesive on the surface of the door. These damage the surface, causing it to lose its dirt repellent protective coating. ~ The high-quality surface of the door is supsceptible to scratching. Even fridge magnets can cause scratching. Disposal of your old appliance ~ Before disposing of an old appliance, first make the door latch or lock unusable.
How to save energy Installation site Normal energy consumption Increased energy consumption In a ventilated room. In an enclosed, unventilated room. Protected from direct sunlight. In direct sunlight. Not near to a heat source (radiator, oven). Near to a heat source (radiator, oven). Where the ideal ambient room temperature is approx. 20°C. Where there is a high ambient room temperature. Do not cover the ventilation gaps and dust them regularly.
Switching on and off Before using for the first time Important: To ensure the correct functioning of the appliance, let it stand for 1½ to 2 hours after transporting it to its final location before connecting it to the mains. Switching off ^ Press the On/Off button until the temperature display goes out. The cooling system is switched off. Protective foil The stainless steel trim to the interior shelves and the door shelves has a layer of protective foil to prevent damage during transportation.
The correct temperature It is very important to set the correct temperature for storing food in the appliance. Micro-organisms will cause food which is not stored at the correct temperature to deteriorate rapidly. Temperature influences the growth rate of these micro-organisms. Reducing the temperature reduces their growth rate.
Super cool and Dynamic cooling Super cool Dynamic cooling m The Super cool function can be used to rapidly reduce the temperature in the refrigerator section to its lowest setting (depending on the room temperature). When the Dynamic cooling function is not switched on, the natural circulation of air in the appliance will cause different temperature zones in the refrigerator as the cold, heavy air will sink to the lowest section of the appliance.
Super cool and Dynamic cooling Switching off Dynamic cooling ^ Press the Dynamic cooling button m. The Dynamic cooling indicator light will go out. The fan automatically switches off when the door is open.
Using the refrigerator efficiently Different storage zones Due to the natural circulation of the air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of the different zones when placing food in the appliance. This appliance has Dynamic cooling, which helps to keep an even temperature when the fan is running. When Dynamic cooling is switched on, the difference between the various zones is less pronounced.
Using the refrigerator efficiently Food which should not be stored in a refrigerator Not all food is suitable for refrigeration, as some food is sensitive to cold. Cucumbers, for example, become glassy, aubergines bitter and potatoes sweet. Tomatoes and oranges lose their aroma, and the peel on citrus fruit hardens.
Using the refrigerator efficiently – Examples of fruit and vegetables which react strongly to the natural gases given off by other types of fruit and vegetables are: Kiwis, broccoli, cauliflower, brussels sprouts, mangos, honeydew melons, apples, apricots, cucumbers, tomatoes, pears, nectarines and peaches. Example: Broccoli should not be stored with apples, as apples produce a large amount of natural gas to which broccoli is very sensitive.
Adjusting the interior fittings Moving the shelves The shelves can be adjusted according to the height of the food. ^ Raise the shelf, and pull it forwards slightly until the notch at the side is in line with the shelf support. It can then be raised or lowered to the required level. The raised edge at the back must face upwards to prevent food from touching the back of the appliance and freezing to it. Stoppers prevent the shelves from being dislodged by mistake.
Adjusting the interior fittings Fruit and vegetable containers The fruit and vegetable containers are pushed in and out on telescopic runners, and can be completely removed if necessary. ^ Pull the container right out and then lift it up and off. Push the runners back in again to avoid injury or damage. To replace a container, ^ place it back on the fully extended runners a. The front of the runners must be right up against the front of the container b. ^ Then push the container back in c.
Automatic defrost The refrigerator defrosts automatically. Condensate and frost can build up on the back wall of the refrigerator whilst it is in use. You do not need to remove this, as it will defrost and evaporate automatically with the warmth generated by the appliance. The condensate is drained away via a channel and drain hole into an evaporation system at the back of the appliance.
Cleaning and care A range of Miele branded cleaning and conditioning products is available to order from Miele or www.miele-shop.com. Make sure that no water can penetrate into the electronic unit or into the light. Do not let water get into the drainage channel and drain hole when cleaning. Do not use steam cleaning apparatus to clean the appliance. Steam could reach the electrical components and cause a short circuit. The data plate located inside the appliance must not be removed.
Cleaning and care ^ Clean the interior shelves and drawers by hand. These are not suitable for cleaning in a dishwasher. ^ Clean the condensate channel and drain hole frequently, so that condensate can drain away unhindered. Use a straw or similar to clear the drain if necessary. ^ After cleaning, wipe the interior and accessories with a damp cloth and dry with a soft cloth. Leave the door open to air the appliance for a short while.
Cleaning and care Metal grille at the back of the appliance The metal grille at the back of the appliance (heat exchanger) should be dusted at least once a year. A build-up of dust will increase the energy consumption of the appliance. When cleaning the grille, make sure that the pipework and other components do not get broken or damaged in any way. After cleaning ^ Replace all shelves and accessories in the appliance. ^ Insert the plug in the socket and switch on at the mains.
Problem solving guide Repairs to electrical appliances should only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. What to do if . . . . . . the compressor is switching in too frequently and for too long. ^ Check whether the ventilation gaps have been covered over or become dusty.
Problem solving guide ^ Unscrew the lamp b and replace it with a new one. Lamp specification: 220 - 240 V, E 14 fitting See the old lamp for the Wattage required. ^ Replace the lamp cover a. . . . the floor of the refrigerator is wet. The drain hole is blocked. ^ Clean the condensate channel and drain hole. If you still cannot remedy the fault having followed these suggestions, please contact the Miele Service Department.
Noises Normal noises What causes them Brrrrr... Humming noise made by the motor (compressor). This noise can get louder for brief periods when the motor is switching on. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes. Click.... Clicking sounds are made when the thermostat switches the motor on and off. Sssrrrrr.... On multi-zone and frost-free appliances you can sometimes just hear the movement of air circulating inside the appliance. Creak ...
After Sales / Guarantee In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – your Miele Dealer or – Miele (see back cover for contact details). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. This information is given on the data plate inside your appliance. Please note that telephone calls may be monitored and recorded for training purposes. N.B.
Electrical connection Electrical connection U.K. Non-rewireable plugs (BS 1363) All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). The fuse cover must be re-fitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained.
Installation Do not place any appliance which gives off heat, such as a toaster or microwave oven, on top of this appliance, as this would increase the appliance's energy consumption. Side-by-side installation To avoid a build-up of condensation and resultant damage, refrigerators and freezers should not generally be installed side-by-side next to other such appliances. However, some appliances have side-wall heating making them suitable for side-by-side installation with this refrigerator.
Installation Ventilation Aligning the appliance Air at the back of the appliance gets warm. To ensure sufficient ventilation, the air inlet and outlet must not be covered or blocked in any way. They should be dusted on a regular basis. Installation ^ Remove the cable clip from the back of the appliance. ^ Check that all parts at the back of the appliance are unhindered. Carefully remove any hindrance. ^ To align the appliance adjust the feet using the spanner supplied.
Installation Appliance dimensions A B C K 12620 SD 1650 mm 600 mm 630 mm K 11820 SD K 12820 SD K 12820 SD edt/cs 1850 mm 600 mm 630 mm 33
Changing the door hinging The appliance is supplied right-hand hinged. If left-hand door hinging is required, follow the instructions below. To change the door hinging you will need the following tools: – a cross-slotted screwdriver, – a flat-bladed screwdriver, – a selection of Torx screwdrivers, – a spanner. Two people are needed for changing the door hinging. Removing the door handle ^ Pull door handle a towards you. Side section b slides back.
Changing the door hinging Changing over the door Make sure the door shelves are empty! ^ Close the appliance door. ^ Then separate retaining plate f from cover e, by pushing it slightly to the left and then pulling the cover forwards and off. ^ Rotate retaining plate f by 180°. ^ Then fit cover e from the front over retaining plate f, and slide it over to the right. The writing must be visible. ^ Remove cover g, then rotate it by 180° and fit it on the opposite side.
Changing the door hinging ^ Pull hinge pin a together with disc b and adjustable foot c upwards and off. ^ Remove cover cap d. ^ Remove cap h from the bearing bush in the door and refit on the opposite side. ^ Undo screws e and take hinge plate f off. ^ Undo the screw of hinge part h on hinge plate f slightly. Fit it into the hole opposite in hinge plate f and tighten up the screw. ^ Refit cover cap d in the other hole. ^ Remove cover g and fit it into the holes on the opposite side.
Changing the door hinging ^ Screw hinge plate f into position on the opposite side using the two outer long slots only. To make it possible to align the door later, do not replace the centre screw at this stage. ^ Fit hinge plate c onto the opposite side and secure it with screws d. ^ Important. Screw the adjustable foot c into hinge pin a as far as it will go. ^ Align the door with the appliance housing using the long slots in the lower hinge plate. Then tighten the screws.
Changing the door hinging Refitting the handle Please make sure you follow the instructions below carefully when you refit the handle. The door seal will be damaged if the handle is fitted incorrectly. It is important to check that the side section of the handle d does not come into contact with the door seal when opening the door, as this would damage the door seal permanently.
Aligning the appliance door The appliance door can be aligned to the housing using the outer long slots in the lower hinge plate. In the following illustration the door is not shown in the closed position to make it easier to see what you have to do. ^ Remove centre screw a from the hinge plate. ^ Slightly loosen both outer screws b. ^ Align the door by sliding the hinge plate to the left or right. ^ Then tighten screws b again. Screw a does not need to be used again.
Building in the appliance The air inlet and outlet must not be covered or blocked in any way. They should be dusted on a regular basis. When built into a kitchen run (max. depth 580 mm) the appliance can be installed directly next to a kitchen furniture housing unit. The appliance door will protrude in front of furniture fronts at the sides by 34 mm and by 55 mm in the middle of the door. This enables the doors to be opened and shut without being obstructed.
Alteration rights reserved / 1311 K 11820 SD, K 12620 SD, K 12820 SD, K 12820 SD edt/cs M.-Nr.