Operating and Installation Instructions Fridge-Freezer Combination KFN 9753 iD To prevent accidents and machine damage read these instructions before installation or use. en - CA, US M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Turning the appliance on/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Safety lock . . . . . . . . . . . . . . . . . . . . . .
Contents Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Electrical information . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS When using the appliance, follow basic safety precautions, including the following: Read all instructions before installation and use to prevent accidents and machine damage. This appliance is intended for residential use only. Use only as described in this Operating manual. Only use this appliance for its intended purpose. The manufacturer cannot be held responsible for damages caused by improper use of this appliance. This appliance complies with current safety requirements.
IMPORTANT SAFETY INSTRUCTIONS Installation This appliance is top-heavy and must be secured to prevent it from tipping forward. ~ Before installation or service, disconnect the power supply to the work area by unplugging the unit, "tripping" the circuit breaker or removing the fuse. ~ This appliance must be installed and connected in compliance with the installation instructions. ~ Installation and repair work should be performed by a Miele authorized service technician.
IMPORTANT SAFETY INSTRUCTIONS ~ Do not use defrosting sprays or de-icers, as they might contain substances which could damage the plastic parts or which could cause a build-up of gases and pose a danger to health. ~ Do not use any oils or grease on the door seal, as these will cause the seal to deteriorate and become porous with time.
Description of the appliance a On/Off button for independently switching the refrigerator section on and off b Refrigerator section temperature display c Temperature selector buttons for the refrigerator section (+ for warmer; - for colder) d SuperCool button and indicator light g Master switch for switching the whole appliance on and off h Freezer section temperature display i Temperature selector buttons for the freezer section (+ for warmer; - for colder) j SuperFreeze button and indicator light k Audi
Description of the appliance a DynaCool fan (dynamic cooling) b Hinged door shelf c Bottle rack d Adjustable door shelves e Interior lighting f Adjustable interior shelves g Condensate channel and drain hole h Universal container i Fruit and vegetable drawer j Divider* k Bottle shelf l Freezer drawers with calendar * may vary by model 8
Before use Before using for the first time The stainless steel frames of the shelves have a protective plastic coating to prevent scratching during transportation. ^ Do not remove the plastic until the appliance has been installed. The temperature display for the refrigerator section lights up, and the interior lighting comes on when the door is opened. Bars light up in the freezer section display until the selected temperature is reached. The appliance begins cooling.
Before use Turning the appliance on/Off Activating/Deactivating the safety lock Turning the refrigerator section off The refrigerator section can be turned off separately while the freezer section remains on, e.g. during vacation. ^ Press the Super button for the freezer for approx. 5 seconds. ^ Press the On/Off button on the left side of the control panel until the temperature display for the refrigerator section goes out. The Super indicator light flashes, and ; flashes in the temperature display.
Before use Turning off for longer periods of time If the appliance is not going to be used for an extended time (for example, during a vacation) some precautions should be taken.
Setting the temperature Temperature range The temperature can be selected within the following ranges: – Refrigerator: 39°F (4° C) to 48°F (9° C). A temperature of 39°F (4° C) is recommended in the refrigerator section. Setting the temperature in the refrigerator and freezer sections The temperatures for the refrigerator and freezer sections can be set independently using the temperature selection buttons. – Freezer: 3°F (-16° C) to -15 (-26° C).
Setting the temperature Temperature displays The temperature displays flash if: During normal operation, the temperature display shows the temperature in the middle of the refrigerator section and the temperature in the warmest part of the freezer section. – a different temperature is being set, If the temperatures in the appliance are not in the possible temperature display range, dashes will flash in the temperature displays.
Setting the temperature Temperature display brightness The brightness of the temperature display is factory-set to the lowest setting. However when the door is opened, a setting is changed or an alarm is triggered, the temperature display will appear very bright. ^ Hold down the Super button for the freezer for approx. 5 seconds. The Super indicator flashes and ; flashes in the temperature display. ^ Press either of the temperature selection buttons until ^ appears in the display.
Alarm The appliance is equipped with an alarm system, to ensure that the temperature does not rise unnoticed. The alarm system is always operational, it does not need to be turned on. If the temperature becomes too warm, the alarm sounds and the temperature display for the freezer section flashes. The temperature set will determine when the alarm is triggered.
Using the Super and DynaCool functions Super function The Super function is used to rapidly reduce the temperature in the refrigerator and freezer sections to their lowest settings (depending on the room temperature). When used with the refrigerator the Super function is ideal for the rapid cooling of drinks and refrigerating large quantities of food. When used with the freezer the Super function is ideal for freezing large quantities of unfrozen food. The function should be switched on approx.
Using the Super and DynaCool functions DynaCool m DynaCool should also be selected if: If the dynamic cooling function (DynaCool) is not switched on, the natural circulation of air throughout the appliance can create different temperature zones in the refrigerator section, with the colder, heavier air sinking to the lowest section. See "Using the refrigerator efficiently". – the room temperature is high (above approx.
Using the refrigerator efficiently Different storage zones Coldest area Due to the natural circulation of air in the appliance, there are different temperature zones in the refrigerator. Cold, heavy air sinks to the lowest section of the appliance. Make use of these different zones when placing food in the appliance. The coldest area in the refrigerator section is directly above the fruit and vegetable drawers.
Using the freezer efficiently Maximum freezing capacity Placing food in the freezer To ensure that food is frozen thoroughly, the maximum freezing capacity should not be exceeded. See the data plate: "Freezing capacity.....lb/kg/24 hrs". Food to be frozen can be placed anywhere in the freezer section. Freezing food Fresh food should be frozen as quickly as possible. This helps maintain the nutritional value, vitamin content, appearance and taste of the food.
Using the freezer efficiently Freezing large items Defrosting If you would like to freeze large items e.g. turkey or ham, the glass plates between the drawers can be removed. Frozen food can be defrosted in different ways: ^ Remove the top full-width freezer drawer, and carefully lift and slide out the glass plates.
Using the freezer efficiently Cooling drinks quickly Cool pack To cool drinks quickly, turn on the Super function for the freezer. See "Super" for more information. The cool pack prevents the temperature in the freezer from rising too quickly in the event of a power failure. Do not leave bottles in the freezer for more than 1 hour, closed containers could burst. Freezer tray The freezer tray can be used to freeze small items such as berries, herbs and vegetables.
Automatic defrosting Refrigerator section Freezer section The refrigerator defrosts automatically. The freezer defrosts automatically. During normal operation, condensate and frost can form on the rear wall of the refrigerator and drawers. You do not need to remove this build-up, it will defrost and evaporate automatically with the heat generated by the appliance.
Adjusting the interior fittings Moving the shelves To move the split shelf: The shelves can be adjusted according to the height of the food: ^ Remove both halves of the glass. ^ Lift the shelf, pull it forwards slightly, until the notch at the side is in line with the shelf support. It can now be moved up or down as desired. The raised edge at the back of the shelf must face upwards to prevent food from touching the back of the appliance.
Adjusting the interior fittings Moving the adjustable door shelves ^ Lift the shelf up and out of the stainless steel frame. ^ Push the stainless steel frame up and remove, by pulling it forward. ^ Replace the frame at the desired height. Ensure that it is securely pushed back into position. Universal container Food can be stored as well as served in the universal container. The universal container consists of a deep tray a and a shallow tray b. Both trays can be fit into the stainless steel frame.
Cleaning and Care Before cleaning To reduce the risk of electrical shock, disconnect the appliance from the power supply by shutting off the power main, tripping the circuit breaker or unplugging the power cord before maintenance. ^ Turn off the appliance by pressing the main switch on the right side of the control panel. Never use cleaning agents containing abrasive substances such as sand, soda, acids, chlorides or chemical solvents.
Cleaning and Care Ventilation slits ^ Check the ventilation slits regularly. Remove any dirt/dust with a vacuum cleaner or brush. Clean as needed. Door seal Do not use oil or grease on the door seals. This may cause the seals to deteriorate and become porous over time. ^ Clean the door seals with warm water and dry thoroughly After cleaning ^ Return all shelves, drawers and accessories.
Frequently asked questions With the aid of the following guide minor problems can be corrected without a service call. Repairs should only be carried out by a qualified and trained person in strict accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage and may void the warranty. The refrigerator or freezer section does not get cold. Possible fault Solution The machine is not turned on.
Frequently asked questions The door to the freezer section will not open. Possible fault Solution This is not a fault. The suction caused by opening and closing the door too many times in succession prevents it from opening. Wait a few minutes, then try again. It should now open without force. The compressor kicks on very frequently and for too long. The ventilation slits are covered or dusty. Clean with a vacuum or brush.
Frequently asked questions The alarm sounds. Possible fault Solution The appliance door(s) have been open for longer than 60 seconds. Close the door(s). The alarm sounds and the temperature display for the freezer section flashes. The freezer door has been opened This has caused the temperature in the too frequently. freezer to rise above the set temperature. Once the temperature has dropped to the A large amount of food is being correct level again the alarm will stop and frozen at the same time.
Noises Normal noises What causes them? Brrrrr... Humming noise made by the motor (compressor). This noise may get louder for brief periods, whenever the motor kicks in. Blubb, blubb.... A gurgling noise can be heard when coolant is circulating through the pipes. Click.... Clicking sounds occur whenever the thermostat switches the motor on or off. Sssrrrrr.... In multi-zone and frost-free appliances, the movement of air circulating through the appliance can sometimes just barely be heard.
After sales service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting the Technical Service department, please quote the model and serial number of your appliance given on the data plate inside the appliance.
Installation instructions To prevent accidents and machine damage read these instructions before installation or use.
Caring for the environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling center about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc., are disposed of safely and kept out of the reach of babies and young children.
Electrical information ,Avoid the risk of electrical shock - Plug into a grounded 3-prong outlet. - Do not move the ground plug. - Do not use an adapter. - Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. Improper connection of the equipment grounding conductor may result in electric shock.
Installation Installation site Have the appliance installed by a qualified technician, according to the enclosed installation instructions. The manufacturer is not liable for damage to property due to an incorrect installation. ,WARNING This appliance is top-heavy and must be secured to prevent it from tipping forward. The appliance should be installed in a dry, well-ventilated room. Do not install the appliance: - outdoors - in an environment with dripping water - in rooms that are at risk of frost.
Installation Ventilation Before installation The air at the rear wall of the appliance gets warm. Therefore sufficient space must be provided around the appliance for ventilation. ^ Remove the cover strip, the sealing strip and other accessories from the inside and from the exterior rear wall of the appliance. A ventilation gap of at least 1 1/2" (38 mm) must be provided behind the appliance. The air intake to the appliance is made through the base of the installation niche.
Installation Dimensions KFN 9753 iD 38 Freezer section height Niche height A B 695 (27 3/8") 1772 - 1788 (69 3/4" - 70 3/8")
Adjusting the door hinges The door hinges are pre-adjusted so that the appliance doors can be opened wide. By adjusting the hinges the doors' can be modified so they do not open as far. If you would like to cushion the doors for a more gentle opening, you can increase the spring force of the appliance door: For example, when the door is opened if an adjacent wall or piece of furniture is in the way, the door angle should be limited to 90°. ^ Insert the pins (supplied) into the hinges from above.
Adjusting the door hinges Before installing the appliance, you will need to decide which side of the door you would like hinged. For and left-handed door hinge, follow the instructions below. Tools needed: – a Philips head screwdriver, – a flathead screwdriver, – various sizes of Torx screwdrivers, ^ Slightly loosen the fastening screws e at the top, middle and bottom. ^ Slide the appliance doors outwards and unhinge them. ^ Completely unscrew the fixing screws e.
Adjusting the door hinges Removing the door closing device ^ With its exterior facing downwards, place the appliance door on a stable surface. ^ Leave the hinges open and remove the screw in the mounting a. Caution! When uninstalled, the door closing device will snap shut. ^ Loosen the ball joint b using an open ended wrench. ^ Remove the door closing device c together with the ball joint. Do not remove the door closing device from the ball joint! This will damage the device.
Adjusting the door hinges Fastening the dampers ^ With its exterior facing downwards, again place the appliance door on a stable surface. ^ Screw the ball joint b of the door closing device c into the new fixing hole. ^ Pull the door closing device c apart and hook the mounting a onto the hinge. ^ Hold the door closing device in this position and screw the mounting a to the hinge. ^ Hang the appliance doors on the pre-fitted screws and push the doors inward.
Installing the appliance The following installation instructions are for a right-hinged appliance door. If you have converted the appliance door to be left-hinged, you will need to adapt the instructions accordingly. Tools needed: Installing the appliance as a room divider If you wish to install the appliance as a room divider, the back of the installation niche must be fitted with a panel, so the back of the appliance is not exposed.
Installing the appliance Preparing the appliance ^ Push the appliance two-thirds of the way into the installation niche. Ensure that the power cord does not get caught. ^ Slide the cover strip a (nobs facing downwards) into the holder. The nobs will fit into the holes b. ^ Ensure that the power cord can be easily plugged in once the appliance is installed. ^ For 16 mm cabinetry walls only: Clip the spacers e and f onto the upper and lower hinges.
Installing the appliance ^ Open the appliance doors. Installing the appliance ^ Using the screws h (M5 x 22), screw the plastic bracket g to the door opening. Depending on the thickness of the niche walls, push the appliance in until : ^ Using the screws j, loosely secure the fixing bracket i onto the appliance. ^ If necessary, shorten the sealing strip k to match the height of the niche. Remove the protective film.
Installing the appliance This space must also be taken into account with cabinetry that has a receding base, even if it means that the plastic bracket d will project beyond the base of the cabinetry. Attaching the appliance to the installation niche ^ If the cabinetry has door stops (i.e. to protect from slamming): pull the appliance forward by distance h so that a space of 1 5/8" (42 mm) is created. The hinges now project by distance h and the plastic bracket d lines up with the front edge of the hinge.
Installing the appliance Mounting the custom door panels ^ Screw the screw c through the fixing bracket d. ^ Push the bracket towards the niche wall and tighten the screws e. ^ Close the bracket f. ^ Close the appliance doors. ^ Set a gap of 5/16" (8 mm) between the appliance door and the fixing bracket a.
Installing the appliance ^ With a pencil, lightly mark a line down the center of the inside of the custom door. ^ Hang the fixing bracket d with the mounting aids on the inside of the custom door. Align the bracket centrally. ^ Secure the fixing bracket with at least 6 screws e (4 x 14 mm). (For framed doors, use only 4 screws at the edge). ^ Carefully pull the mounting aids up and out f. ^ Turn them around, and fit them into the middle slots of the fixing bracket g for safe keeping.
Installing the appliance Securing the appliance door to the custom door panel ^ Secure the fixing bracket using the pre-drilled holes a using the (4 x 14 mm) screws b. Ensure that the two metal edges are flush (symbol //). – Align depth Z on the custom door: Loosen the screws at the top of the appliance doors c and the bottom of the fixing bracket d. Adjust the custom door to create a space of 1/16" (2 mm) between the custom door and the front edge of the niche.
Installing the appliance The following confirms that the appliance is installed correctly: – The doors close properly. – The doors do not touch the cabinetry. – The seal at the upper corner of the hinged-side contacts tightly. ^ To verify this, place a flashlight in the appliance and close the appliance doors. Turn off the lights and check whether the light is visible from inside the appliance. If light is seen, check the individual installation steps again. ^ Replace the upper cover k.
Subject to change without notice / 1408 KFN 9753 iD M.-Nr.
