Operating and installation instructions Gas hobs To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en-GB M.-Nr.
This hob can be used in countries other than those specified on the appliance and in these operating and installation instructions. It is, however, set up for connection to the gas and electricity supplies in the countries specified. For trouble-free operation of the appliance, it is best to use it in the countries specified for use. For use in other countries, please contact Miele in your country.
Gas-heated appliances Safety precautions to take if you smell gas Turn off the gas emergency control valve immediately. This is usually located near the gas meter. Eliminate all sources of ignition in a safe manner. Do not smoke, light cigarette lighters or matches. Do not operate electrical lights or switches, i.e. do not switch them “On” or “Off”. Open all doors and windows to ventilate the area. If the smell of gas persists, evacuate the building.
Contents Warning and Safety instructions...................................................................... 6 Caring for the environment .............................................................................. 16 Guide to the appliance ...................................................................................... Hob...................................................................................................................... KM 3034-1...............................................
Contents After sales service............................................................................................. Contact in the event of a fault ............................................................................. Data plate ............................................................................................................ Warranty .............................................................................................................. 42 42 42 42 Installation..............
Warning and Safety instructions This hob complies with all relevant local and national safety requirements. Inappropriate use can, however, lead to personal injury and material damage. Read the operating and installation instructions carefully before using the hob. They contain important information on safety, installation, use and maintenance. This prevents both personal injury and damage to the hob.
Warning and Safety instructions Correct application This hob is intended for domestic use and use in other similar environments. This hob is not intended for outdoor use. It is intended for domestic use only to cook food and keep it warm. Any other use is not supported by the manufacturer and could be dangerous.
Warning and Safety instructions Safety with children Children under 8 years of age must be kept away from the hob unless they are constantly supervised. Children over 8 years of age may use the hob without supervision if its operation has been clearly explained to them and they are able to use it safely. Children must be able to understand and recognise the possible dangers caused by incorrect operation. Children must not be allowed to clean the hob unsupervised.
Warning and Safety instructions Technical safety Unauthorised installation, maintenance and repairs can cause considerable danger for the user. Installation, maintenance and repairs must only be carried out by a Miele authorised technician. Damage to the hob can compromise your safety. Check the hob for visible signs of damage. Do not use the hob if it is damaged. Reliable and safe operation of this hob can only be assured if it has been connected to the mains electricity supply.
Warning and Safety instructions Miele can only guarantee the safety of the appliance when genuine original Miele replacement parts are used. Faulty components must only be replaced by Miele spare parts. The hob is not intended for use with an external timer switch or a remote control system. The connection to the gas supply must be carried out by a suitably qualified gas fitter, e.g. a Gas Safe registered technician in the UK (see “Installation – Gas connection”).
Warning and Safety instructions Risk of electric shock. Do not use the hob if it is faulty, or if the ceramic surface is cracked, chipped or damaged in any way. Switch it off immediately, do not touch the appliance surface and disconnect the hob from the mains electricity supply and the gas supply. Contact the Customer Service Department. If the hob is installed behind a cabinet door, do not close the door while the hob is in use. Heat and moisture can build up behind the closed door.
Warning and Safety instructions Correct use The hob gets hot when in use and remains hot for a while after being switched off. There is a danger of burning until the residual heat indicators go out. Due to the high temperatures radiated, objects left near the hob when it is in use could catch fire. Do not use the hob to heat up the room. Oil and fat can overheat and catch fire. Do not leave the hob unattended when cooking with oil and fat.
Warning and Safety instructions You could burn yourself on the hot hob. Protect your hands with heat-resistant pot holders or gloves when handling hot pots and pans. Do not let them get wet or damp, as this causes heat to transfer through the material more quickly with the risk of scalding or burning yourself on steam. Be sure to keep all textiles away from the gas flames. Do not use oversized cloths, tea towels or other similar materials. When using an electrical appliance, e.g.
Warning and Safety instructions Ensure that the flames from the burner do not spread out beyond the base and up the sides of the pan. Do not use pans with very thin bases on this hob, and never heat up empty pans as they could get damaged. This could also damage the appliance. The pan support supplied with the appliance must always be used. Never place a pan on the burner itself. Replace the pan supports carefully to avoid scratching the surface of the hob.
Warning and Safety instructions Cleaning and care Do not use a steam cleaning appliance to clean this hob. The steam could reach electrical components and cause a short circuit.
Caring for the environment Disposal of the packing material Disposing of your old appliance The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety.
Guide to the appliance Hob KM 3034-1 a Large burner i Delete minute minder durations b Small burner j Cooking zone symbol c Wok burner Control knobs for the cooking zones d Medium burner k Front right e Medium burner l Rear right f Pan support (one for each burner) m Middle g In-operation/Residual heat indicators n Rear left h Minute minder o Front left 17
Guide to the appliance KM 3054-1 a Wok burner n Minute minder controls / indicators b Large burner o Delete minute minder durations c Small burner Control knobs for the cooking zones d Medium burner g Front right e Medium burner h Rear right f Pan support (one for each burner) i Rear middle l Cooking zone symbols j Front middle m In-operation/Residual heat indicators k Left 18
Guide to the appliance Control knobs Small, medium and large burners Symbol Description Burner off, the gas supply is turned off Largest flame Smallest flame Wok burner Symbol Description Burner off, the gas supply is turned off Largest flame: inner and outer burner on highest setting. Large flame: outer burner on lowest setting, inner burner on highest setting. Small flame: outer burner off, inner burner on highest setting.
Guide to the appliance Burner Small, medium and large burners Wok burner a Burner cap b Burner head c Burner base d Thermocouple a Outer burner cap b Inner burner cap c Burner head d Burner base e Thermocouple f Ignitor 20 e Ignitor
Guide to the appliance Minute minder controls / indicators a Activate system lock/set the time b Minute minder - For switching on and off - For switching between functions - For selecting a cooking zone Indicator lights c Minute minder d Indicator light for relevant zone, e.g. the rear right cooking zone f Indicator light for half hours if the minute minder setting exceeds 99 minutes e Time display to . to .
Guide to the appliance Accessories supplied The accessories supplied with your appliance as well as a range of optional ones are available to order from Miele (see “Optional accessories”). Wok ring The wok ring supplied gives additional stability to the wok, especially to woks with a rounded base. Combination trivet The combination trivet supplied must be used if you are using pans with a smaller base diameter than that specified in the chart for suitable pans.
Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the “After sales service” section of this booklet. Remove any protective wrapping and stickers. Cleaning the hob for the first time Switching on the hob for the first time The metal components have a protective coating which when heated for the first time will give off a slight smell and possibly some vapours.
Pans Minimum pan base diameter Burner Ø cm Small burner 10 Medium burner 12 Large burner 14 Wok burner 14 Maximum diameter at top of pan Burner Ø cm Small burner 20 Medium burner 22 Large burner 24 Wok burner 26 - Select the pan to suit the size of the burner: large diameter = large burner small diameter = small burner. - Observe the dimensions given in the chart. Using pans that are too large can cause the flames to spread out and damage the surrounding worktop or other appliances.
Pans Wok ring Combination trivet Use the wok ring supplied to give additional stability to pans, especially to woks with a rounded base. The combination trivet must be used if you wish to use a pan with a smaller diameter base than the minimum given in the table. Place the wok ring on the pan support so that it sits securely in position and cannot move (see diagram). The wok is unique among cookware in that it has a small base diameter and a large rim diameter (usually 35-40 cm).
Tips on saving energy - Use a pan lid whenever possible to minimize heat loss. - Wide, shallow pans are preferable to tall, narrow ones. They will heat up faster. - Cook with as little water as possible. - Reduce the size of the flame once the water has come to the boil or the oil is hot enough to fry in. - Use a pressure cooker to reduce cooking times.
Operation Risk of fire with overheated food. Switching on Unattended food can overheat and catch alight. Do not leave the hob unattended whilst it is being used. Press the control lightly and turn it anti-clockwise to the large flame symbol. Rapid ignition system The hob is supplied with a rapid ignition system with the following features: - Rapid ignition without the need to hold the control. - Automatic re-ignition If the flame is extinguished, e.g. by a draught, etc.
Operation Switching on during a power outage Adjusting the flame If there is an interruption to the electricity supply, the gas can be ignited manually, e.g. with a match. The burners can be regulated at any level between the strongest and weakest flame. Press in the relevant control and turn it anti-clockwise to the large flame symbol. Hold the control pressed in and light the gas at the burner with a match. Keep the control pressed in for a further 5-10 seconds and then release it.
Operation Switching off Turn the rotary control clockwise to the position. The gas supply is cut off and the flame goes out. In operation / residual heat indicators The in-operation / residual heat indicators light up when a cooking zone is ignited. They go out when the hob is switched off. If a cooking zone is hot, the indicator will light up as long as residual heat it still present. If the indicator lights are flashing, there is a fault (see “Problem solving guide”).
Minute minder A duration of between 1 minute () and 6 hours (.) can be set. Use the - sensor to reduce the time from . to , and the + sensor to increase the time from to .. The display stops at . and at . To continue beyond this setting, briefly remove your finger from the sensor and then touch it again. Durations exceeding 99 minutes are set in half-hour steps. The half hour is indicated by a dot after the number. Minute minder Setting Touch the sensor.
Minute minder Setting the minute minder for a cooking zone A minute minder can be allocated for any switched on cooking zone. This function can be used simultaneously for all cooking zones. Switch on the required cooking zone. Press and release the control as often as necessary until the indicator light for this zone starts to flash. If several cooking zones are switched on, the indicator lights for the cooking zones being used light up anti-clockwise, starting with the front right.
Safety features Ignition safety The hob is equipped with an ignition safety device. If a gas flame is extinguished, e.g. by food boiling over or by a draught, and re-ignition does not work, the gas supply is switched off. This prevents the release of gas. If you turn the control to the position, the burner is ready for use again. The ignition safety device operates independently from the electricity supply. This means that it will still work if the hob is used during a power cut.
Cleaning and care Danger of burning due to hot Unsuitable cleaning agents surfaces. The hob surface, pan supports and burners will be hot after use. Allow the hob to cool down before cleaning it. To avoid damaging the surfaces of the appliance, do not use: Risk of damage due to moisture ingress. The steam from a steam cleaning appliance could reach live electrical components and cause a short circuit. Do not use a steam cleaner to clean the hob.
Cleaning and care The entire hob should be cleaned after each use. Soften any stubborn soiling beforehand. Dry the hob thoroughly after every damp cleaning to avoid limescale residue. Ceramic surface Risk of damage by pointed objects. The seal between the hob and the worktop could suffer damage. The seal between the ceramic surface and the frame could suffer damage. Do not use pointed objects for cleaning. Not all soiling and residues can be removed using a solution of washing-up liquid.
Cleaning and care Pan supports Remove the pan supports. Clean the pan supports in the dishwasher or with a solution of warm water and a little washing-up liquid applied with a soft sponge. Stubborn soiling should be soaked first. After cleaning, dry the pan supports thoroughly with a clean cloth. Control knobs The control knobs are not dishwasher-safe. The control knobs should only be cleaned by hand. The rotary controls can become discoloured if they are not cleaned regularly.
Cleaning and care Burner Do not clean any parts of the burners in a dishwasher. The surface of the burner cap will become duller with time. This is completely normal and does not indicate material deterioration. The burner should be dismantled and then cleaned by hand using a solution of warm water and a little washing-up liquid applied with a soft sponge. Clean any soiling from the flame openings. Danger of explosion.
Cleaning and care Assembling the small, medium and large burners Place the burner head on the burner base so that the thermocouple and the ignitor extend through their respective holes in the burner head. The burner head must click into place correctly. Place the burner cap flat over the burner head . When correctly positioned, the burner cap will not slide about. Ensure parts are reassembled in the correct order.
Problem solving guide Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it. Problem Cause and remedy The burners do not igThere could be an air lock in the gas pipe. nite when the hob is be- You may need to make several attempts before the ing used for the first burner ignites successfully.
Problem solving guide Problem Cause and remedy The gas flame goes out during use. The burner parts are not positioned correctly. Position the burner parts correctly. The electronic ignition device on the burner is not working. The mains fuse has tripped. If necessary, contact a qualified electrician or Miele Service for assistance. There is food residue stuck between the ignitor and the burner cap. The thermocouple is dirty. Remove any soiling (See “Cleaning and care”).
Problem solving guide Problem Cause and remedy The in-operation/residual heat indicators are flashing and a combination of letters and numbers appears in the minute minder display. The overheating protection mechanism has been activated. Turn all controls clockwise to the position. You can operate the cooking zones again once has disappeared. All other fault codes There is a fault with the electronics. Interrupt the power supply to the hob for approx. 1 minute.
Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These products can be ordered through the Miele Webshop. They can also be ordered from Miele (see end of this booklet for contact details) or from your Miele dealer.
After sales service Contact in the event of a fault In the event of any faults which you cannot remedy yourself, please contact your Miele dealer or the Miele Customer Service Department. You can book a Miele Customer Service Department call-out online at www.miele.com/service. Contact information for the Miele Customer Service Department can be found at the end of this document. Please quote the model identifier and serial number of your appliance (Fabr./SN/ Nr.
*INSTALLATION* Installation Safety instructions for installation Risk of damage from incorrect connection. Incorrect installation can cause damage to the hob. The hob must only be installed by a qualified person. Damage from falling objects. Take care not to damage the hob when fitting wall units or a cooker hood above it. Fit the wall units and the cooker hood before the hob.
*INSTALLATION* Installation Safety distances Safety distance above the hob A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood or if any flammable objects (e.g.
*INSTALLATION* Installation Safety distances to the sides and back of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear or a tall unit or wall on one side (right or left) (see illustrations). Minimum distance between the back of the worktop cut-out and the rear edge of the worktop: 50 mm Not allowed Minimum distance between the worktop cut-out and a wall or tall unit to the right of it: 150 mm.
*INSTALLATION* Installation Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e.g. wood) a minimum safety distance of 50 mm must be maintained between the cut-out and the cladding. If the niche cladding is made from a non-combustible material (e.g.
*INSTALLATION* Installation Installation notes Tiled worktops Seal between the hob and the worktop Damage caused by incorrect installation. Using sealant under the hob could result in damage to the hob and the worktop if the hob ever needs to be removed for servicing. Do not use sealant between the hob and the worktop. The sealing strip under the edge of the hob provides a sufficient seal for the worktop. Grout lines and the hatched area underneath the hob frame must be smooth and even.
*INSTALLATION* Installation Building-in dimensions All dimensions are given in mm.
*INSTALLATION* Installation KM 3054-1 a Front b Casing depth c Mains connection box with mains connection cable, L = 1440 mm d Gas connection R ¹/₂ - ISO 7-1 (DIN EN 10226) e Electronics housing, maximum casing depth 78 mm 49
*INSTALLATION* Installation Installation Installing the hob Preparing the worktop Stick the supplied sealing strip under the edge of the hob. Create the worktop cut-out as shown in the hob diagram. Remember to maintain the minimum safety distances (see “Installation – Safety distances”). Seal any cut surfaces on wooden worktops with a special varnish, silicone sealant or resin to prevent the wood from swelling as a result of moisture ingress. The sealant must be heat-resistant.
*INSTALLATION* Installation Securing the hob Functional check After installing the hob, ignite all burners to check that they are operating correctly: - The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting. - On the highest setting, the flame must have a distinctive and visible core. Secure the hob using the brackets supplied.
*INSTALLATION* Installation Gas connection For any gas work in the UK always use a Gas Safe registered engineer. Risk of explosion due to an incorrect gas connection. If the gas connection is carried out incorrectly, it may result in gas leakage. Connection to the gas supply must only be undertaken by an approved and registered gas installer (GasSafe in the UK) in strict accordance with current local and national safety and building regulations.
*INSTALLATION* Installation Risk of heat damage. Gas connections, pipes and connection cables can suffer damage if exposed to heat from the hob. After installation make sure that neither the gas pipe nor the mains cable can come into contact with hot parts of the appliance and that the gas pipe and connections on the hob cannot come into contact with hot gas exhaust. Risk of explosion due to damaged gas pipes. Gas can leak from damaged flexible gas pipes.
*INSTALLATION* Installation Connecting the hob The hob is supplied with a conical ¹/₂" gas connection point. There are two connection options: - Fixed connection - Flexible connection in accordance with DIN 3383 Part 1, maximum length 2000 mm. (Not for the UK.) Risk of explosion due to gas leakage. Unsuitable sealant will not ensure the required leak protection for connections. Ensure that a suitable sealant is used.
*INSTALLATION* Installation Burner ratings Nominal ratings Burner Gas type Highest setting Lowest setting kW g/h kW Small burner Natural gas H Liquid gas 1.0 0.95 – 69 0.25 0.2 Medium burner Natural gas H Liquid gas 1.7 1.7 – 124 0.3 0.35 Large burner Natural gas H Liquid gas 2.7 2.55 – 186 0.5 0.6 Wok Natural gas H Liquid gas 4.7 4.6 – 335 0.3 0.25 Total Natural gas H Liquid gas 11.8 11.
*INSTALLATION* Installation Electrical connection Total power rating All electrical work must be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations (BS 7671 in the UK). Connection must be made via a switched socket. This will make it easier for service technicians should the appliance need to be repaired. The electrical socket must be easily accessible after installation. See data plate Danger of injury.
*INSTALLATION* Installation Disconnecting from the mains Risk of electric shock. There is a risk of electric shock if the appliance is connected to the mains supply during repair or service work. After disconnection, ensure the appliance cannot be switched back on by mistake. To disconnect the appliance from the mains power supply, do one of the following depending on installation: Safety fuses Replacing the mains connection cable Risk of electric shock.
*INSTALLATION* Converting to another gas type Risk of explosion due to an in- Jet table correct conversion. If the conversion to another type of gas is carried out incorrectly, it may result in gas leakage. Conversion from one type of gas to another must only be undertaken by an approved and registered gas installer in strict accordance with current local and national safety and building regulations (GasSafe in the UK).
*INSTALLATION* Converting to another gas type Changing the jets Wok burner Disconnect the hob from the electricity supply and turn off the gas supply. Changing the main jets Small, medium and large burners Remove burner caps and burner head . Remove the pan support, burner cap and burner head . Using an M7 socket spanner, unscrew the main jets . Using an M7 socket spanner, unscrew the main jet Fit the correct jets securely (see jet table).
*INSTALLATION* Converting to another gas type Changing the small jets To change the small jets, the burner fixing screws must first be loosened and the upper section of the appliance removed. Pull the control knobs off. Remove the burner components. Lift the top of the appliance off (see illustration). Using a small screwdriver, unscrew the small jet in the gas fitting. Pull out the jet with a pair of pliers. Fit the correct jets securely (see jet table).
*INSTALLATION* Converting to another gas type Functional check Check all gas fittings for leaks. Reassemble the hob. Ignite all burners to check that they are operating correctly. - The flame must not go out on the lowest setting, or when the control is turned quickly from the highest to the lowest setting. - On the highest setting, the flame must have a distinctive and visible core. Adhere the label supplied with the jets, stating the type of gas being used.
Product data sheets The following data sheets apply to the models described in this operating instruction manual. Information for domestic gas-fired hobs In acc. with regulation (EU) No. 66/2014 MIELE Model name/identifier KM 3034-1 Number of gas burners Energy efficiency per gas burner (EEgas burner) 1. = 55,6 3. = 54,3 4. = 57,1 5. = 60,1 Energy efficiency for the gas hob calculated per kg 56,8 (EEgas hob) Information for domestic gas-fired hobs In acc. with regulation (EU) No.
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk/service, E-mail: info@miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500 Fax: +86 21 6157 3511 E-mail: info@miele.
KM 3034-1, KM 3054-1 en-GB M.-Nr.
