Operating and installation instructions Ceramic hobs with induction To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
Contents Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 KM 6328 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 KM 6366 / KM 6367 . . . . . . . . .
Contents Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Optional accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Safety instructions for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Safety distances. . . . . . . . . . . . . . . .
Warning and Safety instructions This hob complies with all relevant safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time. They contain important notes on installation, safety, use and maintenance. Miele cannot be held liable for damage caused by non-compliance with these Warning and Safety instructions.
Warning and Safety instructions Correct application ~ This hob is not designed for commercial use. It is intended for use in domestic households and similar working and residential environments. ~ The appliance is not intended for outdoor use. ~ It is intended for domestic use only to cook food and keep it warm. Any other use is not supported by the manufacturer and could be dangerous.
Warning and Safety instructions Safety with children ~ Children under 8 years of age must be kept away from the appliance unless they are constantly supervised. ~ Children 8 years and older may only use the appliance unsupervised if they have been shown how to use it in a safe way and can recognise and understand the consequences of incorrect operation. ~ Children must not be allowed to clean the appliance unsupervised.
Warning and Safety instructions Technical safety ~ Unauthorised installation, maintenance and repairs can cause considerable danger to users. Installation, maintenance and repair work must only be carried out by a Miele authorised technician. ~ A damaged appliance can be dangerous. Check the appliance for visible signs of damage. Do not use a damaged appliance. ~ The electrical safety of this appliance can only be guaranteed if correctly earthed.
Warning and Safety instructions ~ While the appliance is under guarantee, repairs should only be undertaken by a service technician authorised by Miele. Otherwise the guarantee is invalidated. ~ The manufacturer can only guarantee the safety of the appliance when original Miele replacement parts are used. Faulty components must only be replaced by genuine Miele original spare parts. ~ The hob is not intended for use with an external timer switch or a remote control system.
Warning and Safety instructions Correct use ~ Oil and fat can overheat and catch fire. Do not leave the appliance unattended when cooking with oil or fat. If oil or fat does catch fire, do not attempt to put out the flames with water. Disconnect the appliance from the mains and use a suitable fire blanket, saucepan lid, damp towel or similar to smother the flames. ~ Flames could set the grease filters of a cooker hood on fire. Do not flambé under a cooker hood.
Warning and Safety instructions ~ You could burn yourself on the hot hob. Protect your hands with heat-resistant pot holders or gloves when handling hot pots and pans. Do not let them get wet or damp, as this causes heat to transfer through the material more quickly with the risk of scalding or burning yourself.
Warning and Safety instructions ~ Grains of salt, sugar and sand (e.g. from cleaning vegetables) can cause scratches if they get under pan bases. Make sure that the ceramic surface is clean before placing pans on it. ~ Even a light object could cause damage in certain circumstances. Do not drop anything on the ceramic surface. ~ Do not place hot pans on the sensors and display as this could cause damage to the electronics underneath. Do not place hot pans on the area around the display.
Warning and Safety instructions ~ This hob is fitted with a cooling fan. If a drawer is fitted directly underneath the hob, ensure that there is sufficient space between the drawer and its contents and the underside of the appliance in order to ensure sufficient ventilation of the hob. Do not store pointed or small items or paper in the drawer. They could get in through the ventilation slots or be sucked into the housing by the fan and damage the fan or impair cooling.
Guide to the appliance Models KM 6328 b c 8 8 8 8 d a e abcd PowerFlex cooking zones with TwinBooster can be combined to form a PowerFlex cooking area: a+b c+d e Control panel 14 00
Guide to the appliance KM 6366 / KM 6367 ab PowerFlex cooking zones with Booster cdef PowerFlex cooking zones with TwinBooster can be combined to form a PowerFlex cooking area: a+b c+f d+e g Control panel 15
Guide to the appliance Sensor controls / displays m 8 i l j 00 8 min k d c e 16 f g hb a
Guide to the appliance Sensor controls a On/Off b Stop and Go c Timer - For switching on - For switching between timer functions For selecting the switch-off time (see "To switch off a cooking zone automatically") d For setting the time e Keeping warm function f For setting the power level g For switching on the PowerFlex cooking area a + b System lock Indicator lights h System lock Cooking zone displays i 0 ^ 1 to 9 f h ß # A g = = = = = = Cooking zone ready for use Keeping warm function Power levels
Guide to the appliance Cooking zones Cooking zone KM 6328 Minimum to maximum C in cm* Rating in watts for 230 V** y w x z 15–23 Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 y+w z+x 22–23 / 15 x 23 – 23 x 39 Normal TwinBooster level 1 TwinBooster level 2 3400 4800 7400 Total: 7400 Cooking zone y w b v x z KM 6366 / KM 6367 Minimum to maximum C in cm* 15–23 Rating in watts for 230 V** Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 y+w 22–23 / 15 x 23 – 23 x 3
Caring for the environment Disposal of the packing material Disposing of your old appliance The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain valuable materials.
Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate, guarantee" section of this booklet. Cleaning for the first time ^ Remove any protective wrapping and adhesive labels. ^ Before using for the first time, clean the appliance with a damp cloth only and then wipe dry.
Induction The induction principle An induction coil is located under each cooking zone. When a cooking zone is switched on, this coil creates a magnetic field which impacts directly on the base of the pan and heats it up. The cooking zone itself is heated up indirectly by the heat given off by the pan. An induction cooking zone only works when a ferromagnetic pan is placed on it (see "Pans").
Induction Noises When using an induction cooking zone, the following noises can occur in the pan, depending on what it is made of and how it has been constructed. – On the higher power levels, it might buzz. This will decrease or cease altogether when the power level is reduced. – If the pan base is made of layers of different materials (e.g. in a sandwiched base), it might emit a cracking sound.
Induction Pans Suitable pans include: – stainless steel pans with a magnetic base – enamelled steel pans – cast iron pans Unsuitable pans: – stainless steel pans without a magnetic base – aluminium and copper pans – glass, ceramic or earthenware pots and pans To test whether a pot or pan is suitable for use on an induction hob, hold a magnet to the base of the pan. If the magnet sticks, the pan is suitable.
Power level range Settings Melting butter Dissolving gelatine 1 to 2 Making milk puddings 2 Warming small quantities of liquid Cooking rice Defrosting frozen vegetables Cooking pulses 3 Warming liquid and semi-solid foods Making omelettes and lightly frying eggs Steaming fruit Cooking dumplings 4 Steaming vegetables, fish Defrosting and reheating frozen food 5 Bringing large quantities of food to the boil, e.g. casseroles Thickening custard and sauces, e.g.
Operation How the hob is operated The hob is equipped with electronic sensor controls which react to finger contact. To operate the hob, touch the relevant sensor. Each time you touch a sensor, an audible tone sounds. Take care to keep the control panel clean and do not place anything on top of it. The sensors may fail to react or they could mistake the article or any dirt for a fingertip contact, thereby activating a function or even causing the hob to switch off automatically (see "Safety switch-off").
Operation Do not leave the appliance unattended whilst it is being used. To switch the hob on ^ Touch the s sensor. 0 will appear in each of the cooking zone displays. If no further entry is made, the hob will switch itself off after a few seconds for safety reasons. Setting and altering the power level ^ Touch the appropriate number on the numerical keypad of the cooking zone you wish to use. The selected power level is shown in the cooking zone display.
Operation Auto heat-up When Auto heat-up has been activated, the cooking zone switches on automatically at the highest power setting and then switches to the continued cooking setting selected. The heat-up time depends on which continued cooking setting has been chosen (see chart). To activate Auto heat-up ^ Touch the number of the continued cooking setting you require until a tone sounds and the continued cooking setting selected starts flashing.
Operation Booster The cooking zones are equipped with a Booster or TwinBooster (see "Guide to the appliance"). When activated, the power is boosted for a maximum of 10 minutes so that large quantities can be heated up quickly, e.g. when boiling water for cooking pasta. Taking a pan off the zone whilst the Booster is in operation interrupts the Booster function. The cooking zone will automatically revert to power setting 9 at the end of the booster time.
Operation Keeping warm function Each cooking zone has a keeping warm function. This function is for keeping food that has just been cooked warm, i.e. food that is still hot. It is not for reheating food that has gone cold. If the keeping warm function has been activated, the cooking zone will switch off automatically after a maximum of 2 hours. To switch the keeping warm function on/off ^ Touch the 2 sensor for selecting the cooking zone you want. Useful tips – Only use pans for keeping food warm.
Operation Switching off and residual heat indicators Switching off a cooking zone ^ Touch the "0" on the numerical keypad of the cooking zone you wish to use. A 0 will flash in the cooking zone display for a few seconds. If the cooking zone is still hot, the residual heat indicator will then appear in the display. Switching off the hob ^ Touch the s sensor. This switches off all cooking zones. The residual heat indicator will appear in the display of any cooking zone which is still hot.
Tips on saving energy – Use a pan lid whenever possible to minimise heat loss. uncovered covered – Select a smaller pan when cooking small quantities. A smaller pan uses less energy than a larger pan with very little in it. – Cook with as little water as possible. – Once food has come to the boil or the oil in the pan is hot enough for frying, reduce the heat to a lower setting. – Cooking times are greatly reduced when using a pressure cooker.
Timer The timer can be used for two different functions: – to set the minute minder – to set a cooking zone to switch off automatically. You can enter a time up to a maximum of 99 minutes. When the set time has elapsed 00 will appear in the display. At the same time a buzzer will sound for a few seconds. ^ Touch the - or + sensor to switch off the audible tone. Minute minder The minute minder can be used with the hob switched on or off. To set the minute minder time ^ Touch the + sensor.
Timer To switch a cooking zone off automatically You can set a time at the end of which a cooking zone will switch off automatically. All the cooking zones can be programmed at the same time. If the time programmed is longer than the maximum operational time allowed, the cooking zone will switch off after the maximum time allowed (see "Safety switch-off"). ^ Select a power level for the cooking zone you require.
Timer To use both timer functions at the same time The minute minder and automatic switch-off functions can be used at the same time. If you have programmed in one or more switch-off times and would like to use the minute minder as well: ^ Touch the + sensor repeatedly until 00 and min appear in the timer display.
Additional functions Stop and Go Your appliance has a Stop and Go feature which, when activated, reduces the power of all cooking zones in use to power level 1. When Stop and Go is activated, the cooking zone power levels and the setting of the timer cannot be altered and the hob can only be switched off. When Stop and Go is deactivated the cooking zones resume at the power level which was last set and any programmed times will continue to run.
Safety features System lock The hob is fitted with a system lock to prevent it from being switched on without supervision. If the hob is switched on when the system lock is active, LC appears in the timer display for a few seconds. The system lock is deactivated if there is an interruption to the power supply. To activate the system lock ^ Switch the hob on. ^ Touch the and + sensors at the same time until "LC" appears in the timer display. To deactivate the system lock ^ Switch the hob on.
Safety features Safety switch-off Safety switch-off with an over-long cooking time If one of the cooking zones is heated for an unusually long period of time (see chart) and the power level is not altered, the hob will switch itself off automatically and the relevant residual heat indicator will light up. To use the cooking zone again, switch it back on in the usual way.
Safety features Overheating protection All the induction coils and the cooling elements for the electronics are fitted with an overheating protection mechanism. Before the induction coils or cooling elements get too hot, the overheating protection mechanism cuts in in one of the following ways: – If the booster function is being used, this will be switched off. – The power level will be reduced. – The cooking zone will switch off automatically. "E2" appears in the cooking zone display.
Cleaning and care Danger of injury. Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short circuit. The appliance should be cleaned after each use. Let it cool down to room temperature before cleaning. To avoid water marks and limescale deposits, use a soft cloth to dry the appliance after cleaning.
Cleaning and care Do not use washing-up liquid to clean the ceramic surface. Washing-up liquid will not remove all soiling and deposits. It will form an invisible coating which will cause permanent discolouration of the ceramic surface. Clean the hob regularly with a suitable ceramic hob cleaning agent. Wipe off all coarse soiling using a damp cloth. Stubborn soiling may need to be removed with a shielded scraper blade.
Problem solving guide With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. Installation work and repairs to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Do not open the casing of the appliance.
Problem solving guide Problem Possible cause Remedy The smell and vapours will be less noticeable with each subsequent use before dissipating completely. A smell and vapours are given off when a new appliance is being used. The ß symbol flashes alternately with the power setting selected in one of the cooking zones. Use a suitable pan (see There is no pan on the cooking zone, or the pan is "Pans"). unsuitable. After the hob is switched on "LC" appears in the timer display for a few seconds.
Problem solving guide Problem Possible cause Remedy The hob switches off while it is in use and a "flash" appears in the timer display. One or more of the Clean the control panel or sensors have been remove the obstruction (see covered, e.g. by finger "Safety switch-off"). contact, food boiling over or by an object such as an oven glove. The food in the pan does not heat up when the Auto heat-up function is switched on. There is too much food Start cooking at the highest in the pan.
Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These can be ordered online at: or from Miele (see back of manual for contact details). Pans Miele offer a wide range of pans which are perfect for Miele hobs. Please refer to the Miele website for more details on individual products.
Safety instructions for installation The appliance must only be installed and connected to the electricity supply by a suitably qualified and competent person in strict accordance with current national and local safety regulations. Fit the wall units and extractor hood before fitting the hob to avoid damaging the appliance. ~ After installation, ensure that the connection cable is without hindrance and that there is no mechanical obstruction which could damage it.
Safety distances Safety distance above the appliance A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details. If the manufacturer's instructions are not available for the cooker hood, a minimum safety distance of at least 760 mm must be maintained. For any flammable objects, e.g. utensil rails, wall units etc.
Safety distances Safety distances to the sides and back of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear or a tall unit or wall on one side (right or left) (see illustrations). a Minimum distance of 50 mm between the back of the worktop cut-out and the rear edge of the worktop. Not allowed b Minimum distance of 50 mm between the worktop cutout and a wall or tall unit to the right of it.
Safety distances Safety distances underneath the hob Interim shelf To ensure sufficient ventilation to the hob, a certain gap must be left between the underside of the hob and any oven, interim shelf or drawer. It is not necessary to fit an interim shelf underneath the hob, but one may be fitted if you wish. The minimum gap between the underside of the hob and – the top of an oven is 15 mm. – the top of an interim shelf is 15 mm. – the base of a drawer is 75 mm.
Safety distances Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance e of 50 mm must be maintained between the cut-out and the cladding. If the niche cladding is made from a non-combustible material (e. g.
Hob with frame or bevelled edge Installation notes Tiled worktop Seal between the hob and the worktop Do not use sealant between the hob and the worktop. This could result in damage to the hob or the worktop if the hob ever needs to be removed for servicing. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. 50 Grout lines a and the hatched area underneath the hob frame must be smooth and even.
Hob with frame or bevelled edge Building-in dimensions KM 6328 a Front b Casing depth c Mains connection box The mains connection cable (1440 mm long) is supplied separately.
Hob with frame or bevelled edge KM 6366 a Front b Casing depth c Mains connection box The mains connection cable (1440 mm long) is supplied separately.
Hob with frame or bevelled edge Installing the hob Installing the hob Preparing the worktop ^ Feed the mains connection cable down through the cut-out. ^ Make the worktop cut-out according to the dimensions given in the building-in diagram. Remember to maintain the minimum safety distances (see "Safety instructions for installation"). ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture.
Flush-fitted hobs Building-in dimensions KM 6367 a Front b Casing depth c Mains connection box d Stepped cut-out for granite or marble worktops The mains connection cable (1440 mm long) is supplied separately. 54 Please take careful note of the detailed diagrams for the cut-out dimensions in granite and marble worktops.
Flush-fitted hobs Installing the hob Flush fit hobs are only suitable for installation in granite, marble, tiled or solid wood worktops. When using a worktop made from any other material, please check first with the worktop manufacturer that it is suitable for installing a flush fit hob. Certain models are suitable for building into glass worktops - please see advice under "Building-in dimensions". The hob can be installed – in a suitable cut-out in a granite or marble worktop.
Flush-fitted hobs Granite and marble worktops Connecting the mains cable to the appliance Preparing the worktop The mains cable must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations (BS 7671 in the UK). ^ Follow the instructions in the wiring diagram (see "Electrical connection Wiring diagram").
Flush-fitted hobs Solid wood, tiled and glass worktops Preparing the worktop a Worktop Connecting the mains cable to the appliance The mains cable must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations (BS 7671 in the UK). ^ Follow the instructions in the wiring diagram (see "Electrical connection Wiring diagram").
Electrical connection All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current local and national safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. A damaged cable must be replaced by a suitably qualified electrician with a special connection cable of type H 05 VV-F, available from Miele.
Electrical connection The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested and where there is any doubt, the electrical wiring in the home should be inspected by a qualified electrician.
After sales service, data plate, guarantee In the event of any faults which you cannot remedy yourself, please contact: – your Miele dealer, or – Miele (see back of manual for contact details). Please note that telephone calls may be monitored and recorded for training purposes (UK only). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. These are given on the data plate. Space in which to stick the extra data plate supplied with the appliance.
KM 6328 / KM 6366 / KM 6367 en - GB M.-Nr.