Operating and installation instructions Ceramic hobs with induction KM 6357 / KM 6358 KM 6379 KM 6386 / KM 6387 To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
Contents Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 KM 6357 / KM 6358 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 KM 6379 . . . . . . . . . . . . . . . . . .
Contents Safety switch-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Problem solving guide . . . .
Warning and Safety instructions This appliance complies with all relevant safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before installation and before using it for the first time. They contain important notes on installation, safety, use and maintenance.
Warning and Safety instructions Correct application ~ This hob is not designed for commercial use. It is intended for use in domestic households and similar working and residential environments. ~ The appliance is not intended for outdoor use. ~ It is intended for domestic use only to cook food and keep it warm. Any other use is not supported by the manufacturer and could be dangerous.
Warning and Safety instructions Safety with children ~ Children under 8 years of age must be kept away from the appliance unless they are constantly supervised. ~ Children 8 years and older may only use the appliance unsupervised if they have been shown how to use it in a safe way and understand the hazards involved. ~ Children must not be allowed to clean the appliance unsupervised.
Warning and Safety instructions Technical safety ~ Installation, maintenance and repairs may only be carried out by a Miele authorised service technician. Installation, maintenance and repairs by unqualified persons could be dangerous. ~ A damaged appliance can be dangerous. Check the appliance for visible signs of damage. Do not use a damaged appliance. ~ The electrical safety of this appliance can only be guaranteed if correctly earthed.
Warning and Safety instructions ~ While the appliance is under guarantee, repairs should only be undertaken by a service technician authorised by Miele. Otherwise the guarantee is invalidated. ~ The manufacturer can only guarantee the safety of the appliance when original Miele replacement parts are used. Faulty components must only be replaced by genuine Miele original spare parts. ~ The hob is not intended for use with an external timer switch or a remote control system.
Warning and Safety instructions Correct use ~ Oil and fat can overheat and catch fire. Do not leave the appliance unattended when cooking with oil or fat. If oil or fat does catch fire, do not attempt to put out the flames with water. Disconnect the appliance from the mains and use a suitable fire blanket, saucepan lid, damp towel or similar to smother the flames. ~ Flames could set the grease filters of a cooker hood on fire. Do not flambé under a cooker hood.
Warning and Safety instructions ~ If the appliance is installed behind a kitchen furniture door, it may only be used with the furniture door open. Do not close the door whilst the hob in use or whilst there is any residual heat present. ~ The appliance gets hot when in use and remains hot for a while after being switched off. There is a danger of burning until the residual heat indicators go out. ~ You could burn yourself on the hot hob.
Warning and Safety instructions ~ Do not use pots or pans on the hob with bases with pronounced edges or ridges. These could scratch or scour the ceramic glass surface permanently. Only use pots and pans with smooth bases. ~ Grains of salt, sugar and sand (e.g. from cleaning vegetables) can cause scratches if they get under pan bases. Make sure that the ceramic surface is clean before placing pans on it. ~ Even a light object could cause damage in certain circumstances.
Warning and Safety instructions ~ Metal utensils stored in a drawer under the hob can become hot if the appliance is used intensively for a long time. Do not store any metal items or utensils in a drawer under the hob ~ This hob is fitted with a cooling fan. If a drawer is fitted directly underneath the hob, ensure that there is sufficient space between the drawer and its contents and the underside of the appliance in order to ensure sufficient ventilation of the hob.
Guide to the appliance Models KM 6357 / KM 6358 c b a d e a Cooking zone with TwinBooster b Cooking zone with Booster cd PowerFlex cooking zones with TwinBooster c + d can be combined to form a PowerFlex cooking area e Control panel 13
Guide to the appliance KM 6379 ad Cooking zones with Booster bc PowerFlex cooking zones with TwinBooster b + c can be combined to form a PowerFlex cooking area e Control panel 14
Guide to the appliance KM 6386 / KM 6387 b c a f d e ab Cooking zones with Booster c Cooking zone with TwinBooster de PowerFlex cooking zones with TwinBooster d + e can be combined to form a PowerFlex cooking area f Control panel 15
Guide to the appliance Control panel (Example) i h g j 0 1 2 3 4 5 6 7 8 9 k 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 88 0 1 2 3 4 5 6 7 8 9 h 0 1 2 3 4 5 6 7 8 9 m n pl c adb e 16 f o
Guide to the appliance Sensor controls a On/Off b Safety lock c Hours d - For selecting the timer - For switching between the timer functions - For selecting the switch-off time (see "Switching off a cooking zone automatically") e Stop and Go f For setting the power level g Booster/TwinBooster h For switching on the PowerFlex cooking area i - For setting the time - For setting the power level for the middle rear cooking zone, if present j For keeping food warm Indicator lights k Residual heat indicator l In
Guide to the appliance Cooking zones Cooking zone KM 6357 / KM 6358 Minimum to maximum C in cm* Rating in watts for 230 V** y 18–28 Normal TwinBooster level 1 TwinBooster level 2 2600 3000 3700 w 10–16 Normal Booster 1400 2200 b 15–23 Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 x 15–23 Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 b+x 22–23 / 15 x 23 – 23 x 39 Normal TwinBooster level 1 TwinBooster level 2 3400 4800 7400 Total: 7400 * Pans of any di
Guide to the appliance Cooking zone KM 6379 Minimum to maximum C in cm* Rating in watts for 230 V** y 14–20 Normal Booster 1850 3000 w 15–23 Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 x 15–23 Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 z 10–16 Normal Booster 1400 2200 w+x 22–23 / 15 x 23 – 23 x 39 Normal TwinBooster level 1 TwinBooster level 2 3400 4800 7400 Total: 7400 * Pans of any base diameter within the given range may be used.
Guide to the appliance Cooking zone KM 6386 / KM 6387 Minimum to maximum C in cm* Rating in watts for 230 V** y 14–20 Normal Booster 1850 3000 w 10–16 Normal Booster 1400 2200 b 18–28 Normal TwinBooster level 1 TwinBooster level 2 2600 3000 3700 x 15–23 Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 z 15–23 Normal TwinBooster level 1 TwinBooster level 2 2100 3000 3700 x+z 22–23 / 15 x 23 – 23 x 39 Normal TwinBooster level 1 TwinBooster level 2 3400 4800 7400 Total:
Caring for the environment Disposal of the packing material Disposing of your old appliance The transport and protective packing has been selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment. They are, however, essential for the correct functioning of your appliance.
Before using for the first time Please stick the extra data plate for the appliance supplied with this documentation in the space provided in the "After sales service, data plate, guarantee" section of this booklet. Cleaning for the first time ^ Remove any protective wrapping and adhesive labels. ^ Before using for the first time, clean the appliance with a damp cloth only and then wipe dry.
Induction The induction principle An induction coil is located under each cooking zone. When a cooking zone is switched on, this coil creates a magnetic field which impacts directly on the base of the pan and heats it up. The cooking zone itself is heated up indirectly by the heat given off by the pan. An induction cooking zone only works when a ferromagnetic pan is placed on it (see "Pans").
Induction Noises When using an induction cooking zone, the following noises can occur in the pan, depending on what it is made of and how it has been constructed. – On the higher power levels, it might buzz. This will decrease or cease altogether when the power level is reduced. – If the pan base is made of layers of different materials (e.g. in a sandwiched base), it might emit a cracking sound.
Induction Pans Suitable pans include: – stainless steel pans with a magnetic base – enamelled steel pans – cast iron pans Unsuitable pans: – stainless steel pans without a magnetic base – aluminium and copper pans – glass, ceramic or earthenware pots and pans To test whether a pot or pan is suitable for use on an induction hob, hold a magnet to the base of the pan. If the magnet sticks, the pan is suitable.
Power level range The appliance is delivered with 9 power levels programmed as standard. If you wish to fine-tune a setting, you can extend the power level range (see "Programming").
Operation How the hob is operated The hob is equipped with electronic sensor controls which react to finger contact. When the hob is switched off only the symbols for the sensors for switching the hob on and off and the safety lock are visible. When the hob is switched on all the other sensors light up as well. On each of the numerical keypads, "0" lights up at brightness level 2, and numbers 1-9 at brightness level 1.
Operation Do not leave the appliance unattended whilst it is being used. To switch the hob on ^ Touch the s sensor. All the sensors will light up. If no further entry is made, the hob will switch itself off after a few seconds for safety reasons. Activating the cooking zones A cooking zone is not active if only the "0" is lit up in the numerical keypad. ^ Touch the "0" to activate the zone. All the power levels will light up.
Operation PowerFlex cooking area The PowerFlex cooking zones can be combined to form a PowerFlex cooking area. The settings for the cooking area are controlled by the rear or left Powerflex cooking zone and the other numerical keypad goes out, except for the symbol y which remains lit. Activating/deactivating ^ Touch the y sensor.
Operation Auto heat-up When Auto heat-up has been activated, the cooking zone switches on automatically at the highest power setting and then switches to the continued cooking setting selected. The heat-up time depends on which continued cooking setting has been chosen (see chart). Activating ^ Touch the number of the continued cooking setting you require until a tone sounds and the continued cooking setting selected starts flashing. The continued cooking setting selected will flash during the heat-up time.
Operation Continued cooking setting* Heat-up time in minutes and seconds (approx.) 1 0 : 15 1+ 0 : 15 2 0 : 15 2+ 0 : 15 3 0 : 25 3+ 0 : 25 4 0 : 50 4+ 0 : 50 5 2 : 00 5+ 5 : 50 6 5 : 50 6+ 2 : 50 7 2 : 50 7+ 2 : 50 8 2 : 50 8+ 2 : 50 9 - * The continued cooking settings with + after the number are only available if the power level range has been extended (see "Programming").
Operation Booster function The cooking zones are equipped with a Booster or TwinBooster (see "Guide to the appliance"). When activated, the power is boosted for a maximum of 15 minutes so that large quantities can be heated up quickly, e.g. when boiling water for cooking pasta. The booster function can only be used on two cooking zones at the same time.
Operation Whilst the booster is switched on, the B sensor and all of the numbers in the relevant numerical keypad are lit up at brightness level 2. To switch on the Booster ^ Touch the "0" on the numerical keypad of the cooking zone you wish to use. ^ Select a power level if you wish. ^ Touch the B sensor. To switch on the TwinBooster Level 1 ^ Touch the "0" on the numerical keypad of the cooking zone you wish to use. ^ Select a power level if you wish. ^ Touch the B sensor.
Operation Keeping warm function Some cooking zones have a keeping warm function. This function is for keeping food that has just been cooked warm, i.e. food that is still hot. It is not for reheating food that has gone cold. If the keeping warm function has been activated, the cooking zone will switch off automatically after a maximum of 2 hours. To switch the keeping warm function on/off ^ Touch the 2 sensor for selecting the cooking zone you want. Useful tips – Only use pans for keeping food warm.
Operation Switching off and residual heat indicators Switching off a cooking zone ^ Touch the "0" on the numerical keypad of the cooking zone you wish to use. The numbers 1 to 9 will go out after a few seconds. If the cooking zone is still hot, residual heat will then be indicated in the display. Switching off the hob ^ Touch the s sensor. This switches off all cooking zones. All the sensors will go out.
Tips on saving energy – Use a pan lid whenever possible to minimise heat loss. uncovered covered – Select a smaller pan when cooking small quantities. A smaller pan uses less energy than a larger pan with very little in it. – Cook with as little water as possible. – Once food has come to the boil or the oil in the pan is hot enough for frying, reduce the heat to a lower setting. – Cooking times are greatly reduced when using a pressure cooker.
Timer The hob must be switched on to use the timer. The timer can be used for two different functions: – to set the minute minder – to set a cooking zone to switch off automatically. You can select a time from 1 minute (01) to 9 hours (9^). A time of up to 99 minutes is set and displayed in minutes. Example: To set a time of more than 99 minutes, the timer must be set to hours (h). The time is then set in half hour stages. The half hour is indicated by a dot after the number.
Timer Minute minder To set the minute minder time Minutes Example: You want to set 15 minutes. ^ Switch the hob on. ^ Touch the m sensor. The m indicator light will flash. 00 will appear in the timer display. The 0 on the right will flash. h Enter the tens first and then the units. ^ Touch the number on the numerical keypad which corresponds to the tens position (1 in this case). The timer display will change and 1 will start flashing.
Timer Hours Whole hours are set by touching the relevant number on the numerical keypad. Half hours are set by touching the area between the relevant two numbers. Example: You want to set 2 hours 30 minutes. ^ Switch the hob on. ^ Touch the m sensor. The m indicator light will flash. 00 will appear in the timer display. The 0 on the right will flash. h ^ Touch the h sensor, to change the display to show the hours. h ^ Touch the area between the numbers 2 and 3 on the numerical keypad.
Timer To change the minute minder time ^ Touch the m sensor. ^ Set the time you want, as described above. To delete the minute minder time ^ Touch the m sensor. ^ Touch 0 on the numerical keypad.
Timer To switch a cooking zone off automatically You can set a time at the end of which a cooking zone will switch off automatically. All the cooking zones can be programmed at the same time. If the time programmed is longer than the maximum operational time allowed, the cooking zone will switch off after the maximum time allowed (see "Safety switch-off"). ^ Select a power level for the cooking zone you require. ^ Touch the m sensor repeatedly until the indicator light for this cooking zone flashes.
Timer To use both timer functions at the same time The minute minder and automatic switch-off functions can be used at the same time. If you have programmed in one or more switch-off times, and would like to use the minute minder as well: Touch the m sensor repeatedly until the indicator lights for the cooking zones you have programmed light up constantly and 00 appears in the timer display.
Safety features Safety lock / System lock Keep children away from the hob for their own safety. Your appliance is equipped with a safety lock to prevent the hob and the cooking zones being switched on or any settings being altered. The safety lock is set with the hob switched on. When activated: – The cooking zone power levels and the timer settings cannot be changed. – The cooking zones, the hob and the timer can be switched off, but once switched off cannot be switched on again.
Safety features Activating Three-finger operation (standard default setting) ^ Touch the $ sensor and the "0" setting of both right-hand cooking zones at the same time until the safety lock indicator lights up and LC appears in the timer display. The safety lock indicator and LC will go out after a short while. One-finger operation ^ Touch the $ sensor until the safety lock indicator lights up and LC appears in the timer display. The safety lock indicator and LC will go out after a short while.
Safety features Stop and Go Your appliance has a Stop and Go feature which, when activated, reduces the power of all cooking zones in use to power level 1. When Stop and Go is activated, the cooking zone power levels and the setting of the timer cannot be altered and the hob can only be switched off. When Stop and Go is deactivated, the cooking zones resume at the power level which was last set. If Stop and Go is not deactivated, the hob switches off after 1 hour.
Safety features Safety switch-off Safety switch-off with an over-long cooking time If one of the cooking zones is heated for an unusually long period of time (see chart) and the power level is not altered, the hob will switch itself off automatically and the relevant residual heat indicator will light up. To use the cooking zone again, switch it back on in the usual way.
Safety features Overheating protection All the induction coils and the cooling elements for the electronics are fitted with an overheating protection mechanism. Before the induction coils or cooling elements get too hot, the overheating protection mechanism cuts in in one of the following ways: Induction coils – If the booster function is being used, this will be switched off. – The power level will be reduced. – The cooking zone will switch off automatically.
Cleaning and care Danger of injury. Do not use a steam cleaning appliance to clean this appliance. The steam could reach electrical components and cause a short circuit. The appliance should be cleaned after each use. Let it cool down to room temperature before cleaning. To avoid water marks and limescale deposits, use a soft cloth to dry the appliance after cleaning.
Cleaning and care Do not use washing-up liquid to clean the ceramic surface. Washing-up liquid will not remove all soiling and deposits. It will form an invisible coating which will cause permanent discolouration of the ceramic surface. Clean the hob regularly with a suitable ceramic hob cleaning agent. Wipe off all coarse soiling using a damp cloth. Stubborn soiling may need to be removed with a shielded scraper blade.
Programming You can change the default settings of the programme options (see chart). Several settings can be altered in succession. After selecting programming mode, P (Programme) and S (Status) will appear in the timer display. On hobs with 3 cooking zones, an additional indicator will appear at the rear left. The programme is shown in the numerical keypad displays at the front left and rear left.
Programming Programme* P P P P P P P * 0 1 2 3 4 5 6 Demonstration mode and factory default settings Stop and Go Power level range Induction warning tone when there is no pan or the pan is unsuitable Keypad tone when a sensor is touched Timer audible tone Safety lock Status** Setting S 0 Demonstration mode on S 1 Demonstration mode off S 9 Factory default settings reinstated S 0 Off S 1 On S 0 9 power levels (1, 2, 3 ...
Programming Programme* P P P P P 7 8 10 15 16 System lock Status** Setting S 0 Manual activation of the system lock only S 1 Manual and automatic activation of the System lock S 0 Off S 1 On Miele|home - only on communication-enabled appliances fitted with a communication module.
Problem solving guide With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. Installation work and repairs to electrical appliances must only be carried out by a suitably qualified and competent person in strict accordance with current local and national safety regulations. Do not attempt to open the casing of the appliance.
Problem solving guide Problem Possible cause Remedy The smell and vapours will be less noticeable with each subsequent use before dissipating completely. A smell and vapours are given off when a new appliance is being used. The power levels 1 to 9 flash. There is no pan on the Use a suitable pan (see cooking zone, or the pan is "Pans"). unsuitable. After the hob is switched on "LC" appears in the timer display for a few seconds. The system lock is activated.
Problem solving guide Problem Possible cause Remedy Power level 9 is automatically reduced if you select power level 9 on two linked cooking zones or extended zones at the same time. Operating both zones at power level 9 would exceed the permitted maximum power level for the two zones. The hob switches off while it is in use and an F flashes in the timer display. Clean the control panel or One or more of the remove the obstruction (see sensors have been covered, e.g. by finger "Safety switch-off").
Problem solving guide Problem Possible cause Remedy The sensors are over-sensitive or do not react at all. The sensitivity level of the Make sure that there is no sensors has changed. direct light (from the sun or from an artificial source) falling onto the hob and that the surrounding area is not too dark. Make sure that there is nothing covering the sensors or the hob. Take any pans off the hob and wipe away any food deposits. Interrupt the power supply to the hob for approx. 1 minute.
Optional accessories Miele offer a comprehensive range of useful accessories as well as cleaning and conditioning products for your Miele appliances. These can be ordered online at: or from Miele (see back cover for contact details) Pans Miele offer a wide range of pans which are perfect for Miele hobs. Please refer to the Miele website for more details on individual products.
Optional accessories Miele|home system The Miele{home system allows communication-enabled appliances to send operating and status information to a display appliance via the household electrical supply system (Powerline Technology). SuperVision appliances can display status information from other domestic appliances.
Optional accessories Miele|home a Communication enabled appliances (examples) b Communication module c SuperVision appliance d Electrical supply (Powerline) e Miele|home Gateway f WLAN) Router Possible connections (optional) g PC, Notebook h iPod* or iPhone* i Connection with a domestic bus system display j Possible internet connection * * iPod und iPhone are registered trade marks of Apple Inc.
Optional accessories Con|ctivity a Communication module XKM 2000 DA b Communication module XKM 2100 KM c Electrical supply (Powerline) 60
Con|ctivity and Miele|home Signing on the hob If you want to sign the hob – on to the Miele{home system, first prepare the signing on procedure on the master appliance (see the "Miele|home" fitting and installation instructions) – on to the Con|ctivity system, first sign on the cooker hood (see the "Con|ctivity" fitting and installation instructions). ^ With the hob switched off, touch the s and $ sensors at the same time until the safety lock indicator light flashes.
Con|ctivity and Miele|home Signing off the hob If you want to sign off from the Miele{home system, first prepare the signing off procedure on the master appliance (see the "Miele|home" fitting and installation instructions). ^ With the hob switched off, touch the s and $ sensors at the same time until the safety lock indicator light flashes. After selecting programming mode, P (Programme) and S (Status) will appear in the timer display.
Safety instructions for installation The appliance must only be installed and connected to the electricity supply by a suitably qualified and competent person in strict accordance with current national and local safety regulations. Fit the wall units and extractor hood before fitting the hob to avoid damaging the appliance. ~ After installation, ensure that the connection cable is without hindrance and that there is no mechanical obstruction which could damage it.
Safety distances Safety distance above the appliance When two or more appliances which have different safety distances are installed together below a cooker hood, you should observe the greater safety distance of the two. A minimum safety distance must be maintained between the appliance and the cooker hood above it. See the cooker hood manufacturer's operating and installation instructions for details.
Safety distances Safety distances to the sides and back of the hob Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear or a tall unit or wall on one side (right or left) (see illustrations). a Minimum distance of 50 mm between the back of the worktop cut-out and the rear edge of the worktop. Not allowed b Minimum distance of 50 mm between the worktop cutout and a wall or tall unit to the right of it.
Safety distances Safety distances underneath the hob Interim shelf To ensure sufficient ventilation to the hob, a certain gap must be left between the underside of the hob and any oven, interim shelf or drawer. It is not necessary to fit an interim shelf underneath the hob, but one may be fitted if you wish. The minimum gap between the underside of the hob and – the top of an oven is 15 mm. – the top of an interim shelf is 15 mm. – the base of a drawer is 75 mm.
Safety distances Safety distance when installing the appliance near a wall with additional niche cladding A minimum safety distance must be maintained between the worktop cut-out and any niche cladding to protect it from heat damage. If the niche cladding is made from a combustible material (e. g. wood) a minimum safety distance e of 50 mm must be maintained between the cut-out and the cladding. If the niche cladding is made from a non-combustible material (e. g.
Hob with frame or bevelled edge Installation notes Tiled worktop Seal between the hob and the worktop Do not use sealant between the hob and the worktop. This could result in damage to the hob or the worktop if the hob ever needs to be removed for servicing. The sealing strip under the edge of the top part of the appliance provides a sufficient seal for the worktop. 68 Grout lines a and the hatched area underneath the hob frame must be smooth and even.
Hob with frame or bevelled edge Building-in dimensions KM 6357 a Front b Casing depth c Connection for Miele|home d Mains connection box The mains connection cable (1440 mm long) is supplied separately.
Hob with frame or bevelled edge KM 6379 a Front b Casing depth c Connection for Miele|home d Mains connection box The mains connection cable (1440 mm long) is supplied separately.
Hob with frame or bevelled edge KM 6386 a Front b Casing depth c Connection for Miele|home d Mains connection box The mains connection cable (1440 mm long) is supplied separately.
Hob with frame or bevelled edge Installing the hob Installing the hob Preparing the worktop ^ Feed the mains connection cable down through the cut-out. ^ Make the worktop cut-out according to the dimensions given in the building-in diagram. Remember to maintain the minimum safety distances (see "Safety instructions for installation"). ^ Seal the cut surfaces with a suitable heat-resistant sealant to avoid swelling caused by moisture.
Flush-fitted hobs Building-in dimensions KM 6358 a Front b Casing depth c Connection for Miele|home d Stepped cut-out for granite or marble worktops e Mains connection box Please take careful note of the detailed diagrams for the cut-out dimensions in granite and marble worktops. The mains connection cable (1440 mm long) is supplied separately.
Flush-fitted hobs KM 6387 a Front b Casing depth c Connection for Miele|home d Stepped cut-out for granite or marble worktops e Mains connection box The mains connection cable (1440 mm long) is supplied separately. 74 Please take careful note of the detailed diagrams for the cut-out dimensions in granite and marble worktops.
Flush-fitted hobs Installing the hob Flush fit hobs are only suitable for installation in granite, marble, tiled or solid wood worktops. When using a worktop made from any other material, please check first with the worktop manufacturer that it is suitable for installing a flush fit hob. Certain models are suitable for building into glass worktops - please see advice under "Building-in dimensions". The hob can be installed – in a suitable cut-out in a granite or marble worktop.
Flush-fitted hobs Granite and marble worktops Connecting the mains cable to the appliance Preparing the worktop The mains cable must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations (BS 7671 in the UK). ^ Follow the instructions in the wiring diagram (see "Electrical connection Wiring diagram").
Flush-fitted hobs Solid wood, tiled and glass worktops Preparing the worktop a Worktop Connecting the mains cable to the appliance The mains cable must only be connected to the appliance by a qualified and competent electrician in strict accordance with current local and national safety regulations (BS 7671 in the UK). ^ Follow the instructions in the wiring diagram (see "Electrical connection Wiring diagram").
Electrical connection All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current local and national safety regulations (BS 7671 in the UK). Installation, repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. A damaged cable must be replaced by a suitably qualified electrician with a special connection cable of type H 05 VV-F, available from Miele.
Electrical connection The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system, which complies with current local and national safety regulations. It is most important that this basic safety requirement is present and regularly tested and where there is any doubt, the electrical wiring in the home should be inspected by a qualified electrician.
After sales service, data plate In the event of any faults which you cannot remedy yourself, please contact: – your Miele dealer, or – Miele (see back cover for contact details). Please note that telephone calls may be monitored and recorded for training purposes (UK only). When contacting your Dealer or Miele, please quote the model and serial number of your appliance. These are given on the data plate. Space in which to stick the extra data plate supplied with the appliance.
Alteration rights reserved / 1113 M.-Nr.