Operating and Installation Instructions Ceramic Cooktop KM 5621 KM 5624 KM 5627 To prevent accidents and appliance damage, read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Description of the cooktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 KM 5621. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 KM 5624. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 KM 5627. . . . . . . . . . . . . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Children WARNING- When using your appliance follow basic precautions, including the following: Read all instructions before installation or use to prevent injury and appliance damage. This appliance conforms to all uniform safety codes and regulations. Keep these operating instructions in a safe place and pass them on to any future user. SAVE THESE INSTRUCTIONS for a future user.
IMPORTANT SAFETY INSTRUCTIONS Technical safety ~ Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Be sure your appliance is properly installed and grounded by a qualified technician. ~ Before installing the cooktop, check for externally visible damage. Do not operate a damaged appliance.
IMPORTANT SAFETY INSTRUCTIONS Safety ~ DO NOT TOUCH THE COOKING AREA OR THE VICINITY AROUND THE COOKING AREA - During operation, the cooking area and its surroundings will get hot and can cause burns. When the cooktop is shut off, the surface may remain hot enough to cause harm, even though the glow is not visible through the dark glass.
IMPORTANT SAFETY INSTRUCTIONS ~ Make certain that the power cords of small appliances do not come in contact with the appliance. The insulation of the cable could become damaged. Danger of electric shock! ~ To prevent damage to the cooktop ~ Areas around the cooktop (the cooktop frames or surrounding (in the case of beveled cooktops) may become hot due to the following factors: operating time, high output settings, large cook ware, and number of burners in operation.
IMPORTANT SAFETY INSTRUCTIONS ~ Any spills should be removed as quickly as possible to prevent them from burning on and becoming difficult to remove. ~ Aluminum cookware or cookware with aluminum base can cause shiny metallic spots. These spots can be removed with ceramic glass or stainless steel cleaner (see "Cleaning and Care"). ~ Never heat up an empty pot, unless the manufacturer explicitly allows this do be done! Failure to comply can result in a damaged cooktop.
Description of the cooktop KM 5621 ac Variable burner Control knobs for the burners: bd Standard burner f left rear g right rear h right front i left front e Residual heat indicator Burner data C Diameter Burner Left front a Left rear b inch cm Output in Watts at 208/240 V 4 3/4" / 8 1/4" 12 / 21 900 / 2400 14.5 1200 5 11 /16" Right rear c 4 3/4" / 7 1/16" 12 / 18 700 / 1800 Right front d 11 14.
Description of the cooktop KM 5624 ac Variable burner Control knobs for the burners: bd Standard burner f left rear g right rear h right front i left front e Residual heat indicator Burner data C Diameter Burner Left front a inch cm Output in Watts at 208/240V 7 1/16" / 9 1/16" 18 / 23 1600 / 2500 14.
Description of the cooktop KM 5627 acde Variable burners b Standard burner f Residual heat indicator Control knobs for the burners: g left rear h center rear i right rear j right front k left front Burner data C Diameter Burner Left front a inch cm 208 V 240 V 7 1/16" / 9 1/16" 18 / 23 1600 / 2500 1600 / 2500 14.
Before using for the first time Clean the cooktop ^ Before using for the first time, clean the appliance with a damp cloth and dry with a soft cloth. Do not use liquid dish soap to clean the cooktop, this may cause permanent blue discolorations. Heat the cooktop Only for facet cooktops: A small gap between the cooktop and the work surface may be visible in the first days of operation. It will become smaller during use. Despite this small gap, the electrical safety of your appliance is always ensured.
How the burners operate One-zone burners use one heating strip; two-zone burners and grill zones have two heating strips. Depending on the model, the heating strips may be separated by a ring. One-zone burner Each burner has overheating protection (internal temperature limiter) feature to prevent the ceramic glass from overheating (see "Overheat protection"). When a power level is set, the heat element turns on and the heating strip is visible through the ceramic glass.
Operation The burners are turned on when the corresponding control knob is pressed in and rotated to the desired output level. Turning on Control knobs for one-ring burners can be rotated 360°. Burners can be turned on and off by turning the knobs to right or to left. ^ Press in the control knob and rotate it: Control knobs for variable burners have a stop. Burners can be turned On by turning the knob to the right, and turned Off by turning it to the left.
Operation Residual heat indicator After turning on a burner, for example the left front, a specified temperature is reached, the associated residual heat indicator lights up. After turning off the burner, the residual heat indicator will go out. The residual heat indicator will turn off once the cooking zone is safe to the touch. Do not touch the burner or rest any objects on the cooktop when the residual heat indicator is on.
Selecting cookware – Use cookware with thick, flat, smooth bottoms. Slightly concave bottoms will also work adequately. Pans with convex bottoms will not cook well. cold Energy saving tips – For the most even and energy efficient cooking, the diameter of the pots/pans should match the diameter of the burners as closely as possible. hot – Cast iron, glass or stoneware should not be used because they have poor heat transfer and may scratch the cooktop surface.
Overheat protection Each cooking zone is equipped with a temperature limiter. This feature automatically turns off the heating element before the glass ceramic becomes too hot. Once the ceramic surface has cooled to a safe temperature the heating element will automatically turn back on. The overheat protection may be activated by: – turning on a burner without putting a pan on it. – heating an empty pan. – an uneven pan not sitting evenly on the burner. – the pan not conducting heat properly.
Cleaning and Care Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit. Pressurized steam could cause permanent damage to the surface. Do not use any sharp pointed objects which could damage the seal between the ceramic surface, the surrounding frame and the countertop. Never use abrasive cleaners, caustic (oven) cleaners, dishwasher detergent, scouring pads, steel wool or hard brushes. They will damage the surface.
Frequently asked questions ,Repairs should be carried out only by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. Problem Possible cause Solution Burners do not heat up when turned on The circuit breaker has tripped. Check whether a fuse is blown. If the problem persists contact Miele. The appliance turns off during use. The operating time for one burner was too long. See "Overheat protection".
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance. Adhere rating label sticker supplied with the appliance below.
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire. The cabinetry and venting hood should be installed first to prevent damage to the cooktop. ~ This appliance has not been designed for maritime (e.g.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Safety distance from divider Installation of a divider under the cooktop is not required. Safety distances above the appliance If a divider is fitted under the cooktop, the distance between the upper edge of the work surface and the upper edge of the divider must be at least 4 ½ " (110 mm). A gap of at least 1 3/8"" (35 mm) must be provided between the rear edge of the divider and the rear wall of the cabinet so that the power cord can be passed through.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown. Do not install the appliance between two tall cabinets, this is a fire hazard. not allowed a 1 5/8" (40 mm) minimum distance from the countertop cut-out to the rear edge of countertop or wall.
Installation Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials. If the covering is made of a combustible material (such as wood), the distance between the countertop cut-out and the wall covering must be a minimum of 2" (50 mm).
Installation Frame/Facet Cooktops Sealing Tiled surfaces The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. The grouting a and shaded area under the appliance frame must be flat and even so that the frame will lie evenly and the sealing strip under the edge of the upper part of the appliance can provide an adequate seal against the countertop.
Installation dimensions KM 5621 5/8" (54 (544 24 m) 6m 2 1/8" " 1/4 m) (7 m 21 7/16" mm) (62 16" c 15/ 2 m) m (75 mm ) c (05 6" 3/1 a a 6" 3/14 mm 2 0m" m) m) 1 30 m (0 0R 203/8" (51 8 +-1 6" 22 mm ) 5/1 m) + 1m 67 (5 20 (6 " 3/8m) 2 m 0 (6 " 3/8 ) m m b " 5/8 16" c6" 15/ ) m) /1 m 2 161/8" (75 mm 211 m) (67 m (409 (68 mm ) 3 15/16" (100 mm ) 2 6" 5/1 ) 19 1 mm 49 b ( (20 83 8 m /16" m) (50 201/16 " 9m m ) 8" 5/ ) m 9 4m 4 e (2 6" /1 m) 15 8 m 2
Installation dimensions KM 5624 a Spring clips b Front c Installation height d Power cord, L = 56 11/16" (1440 mm) e Rating label 28
Installation dimensions KM 5627 a Spring clips b Front c Installation height d Power cord, L = 56 11/16" (1440 mm) e Rating label 29
Installation Wood or solid surface countertop The exact positions of the spring clamps and the support bars (for beveled cooktops only) are shown in the "Installation dimensions" of each unit. Facet cooktops: A special sealing strip ensures the slip-proof seating of the cooktop in the cutout. The gap between the frame and the countertop will narrow after a little time has passed. ^ Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture. The materials used must be heat resistant.
Installation Granite countertop Strong double-sided adhesive tape and silicon are required for installation (not included). ^ Coat the lateral edges and the lower edge of the spring clips and securing strips with silicon. ^ Using adhesive tape c attach the spring clips and the securing strips (for facet cooktops only) The spring clips and the securing strips must be on or flush with the top edge of the cooktop.
Installation Insert the cooktop ^ Feed the power cord down through the cut-out. ^ Place the cooktop lightly on the spring clips. ^ With a hand on each side of the appliance press down evenly on the edges until it clicks into position. When doing so make sure that the appliance seal sits tightly on the countertop to ensure it is sealed correctly. This is important to ensure an effective seal. Do not permanently seal into the countertop.
Electrical connection ,CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held responsible.
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Alteration rights reserved / 1811 M.-Nr. 07 844 520 / 01 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
