Operating and Installation Instructions Ceramic Cooktop KM 5820 To prevent accidents and appliance damage, read these instructions before installation or use. en - US, CA M.-Nr.
Contents IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Cooktop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Before using for the first time. . . . . . .
IMPORTANT SAFETY INSTRUCTIONS Children WARNING- When using your appliance follow basic precautions, including the following: ~ Use the safety lock to ensure that Read all instructions before installation or use to prevent injury and appliance damage. unattended in an area where the appliance is in use. Never allow children to sit or stand on any part of the appliance. Caution: Do not store items of interest to children in cabinets above the appliance.
IMPORTANT SAFETY INSTRUCTIONS Technical safety ~ Installation, repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and may void the warranty. ~ Be sure your appliance is properly installed and grounded by a qualified technician. ~ Before installing the cooktop, check for externally visible damage. Do not operate a damaged appliance.
IMPORTANT SAFETY INSTRUCTIONS Safety ~ DO NOT TOUCH THE COOKING AREA OR THE VICINITY AROUND THE COOKING AREA - During operation, the cooking area and its surroundings will get hot and can cause burns. When the cooktop is shut off, the surface may remain hot enough to cause harm, even though the glow is not visible through the dark glass.
IMPORTANT SAFETY INSTRUCTIONS ~ Make certain that the power cords of small appliances do not come in contact with the appliance. The insulation of the cable could become damaged. Danger of electric shock! ~ To prevent damage to the cooktop ~ The control panel and/or the areas around the cooktop (the cooktop frames or surrounding (in the case of facet cooktops) may become hot due to the following factors: operating time, high output settings, large cook ware, and number of burners in operation.
IMPORTANT SAFETY INSTRUCTIONS ~ Any spills should be removed as quickly as possible to prevent them from burning on and becoming difficult to remove. ~ Aluminum cookware or cookware with aluminum base can cause shiny metallic spots. These spots can be removed with ceramic glass or stainless steel cleaner (see "Cleaning and Care"). ~ Never heat up an empty pot, unless the manufacturer explicitly allows this can be done! Failure to comply can result in a damaged cooktop.
Description of the appliance Cooktop a Three-zone variable burner b Two-zone variable burner c One-zone burner d Control panel Burner C Diameter inches cm Output in watts at 208 / 240 V 5 11/16" 8 1/4" 10 5/8" 14.5 21 27 1100 2150 3100 Right rear b 4 3/4" 7 1/16" 12 18 700 1800 Right front c 5 11/16" 14.
Description of the appliance Control panel 10
Description of the appliance Touch controls a Cooktop On/Off b Settings bar - Setting the power level - Setting the time c Child safety lock d Variable burner On/Off e Burner On/Off f Stop and Go g - Timer activation - Switching between timer functions - Selecting the shut-off time (see "Automatic burner shut-off") h Hour function Indicator lights i Power-ON indicator j Child safety lock k Variable burner-On Burner display l0 1 to 9 # A = = = = = Burner is ready for use Burner is turned on Power level Res
Before using for the first time Clean the cooktop ^ Before using for the first time, clean the appliance with a damp cloth and dry with a soft cloth. Do not use liquid dish soap to clean the cooktop, this may cause permanent blue discolorations. Heat the cooktop Only for facet cooktops: A small gap between the cooktop and the work surface may be visible in the first days of operation. It will become smaller during use. Despite this small gap, the electrical safety of your appliance is always ensured.
How the burners operate One-zone burners use one heating strip; two-zone burners and grill zones have two heating strips. Depending on the model, the heating strips may be separated by a ring. One-zone burner Each burner has overheating protection (internal temperature limiter) feature to prevent the ceramic glass from overheating (see "Overheat protection"). When a power level is set, the heat element turns on and the heating strip is visible through the ceramic glass.
Use Turning ON The cooktop must be turned on before any of the burners can be used. Do not leave the appliance unattended during operation! To turn a burner on and select a power level ^ Touch the On/Off touch control for the desired burner. 0 appears in the burner display. To turn the cooktop On: ^ Touch the s On/Off touch control . The power-ON indicator will turn on and - will appear in all the burner displays.
Use Power settings The cooktop is factory-programmed with 9 power levels. If you would like finer setting control, you can extend the power levels (see "Programming"). The intermediate levels will appear with a lighted dot next to the number. Cooking process Power level* Standard factory settings (9 power levels) Extended settings (17 power levels) Melting butter, chocolate, etc. Dissolving gelatin Preparing yogurt 1-2 1 - 2.
Use Cooking with Auto-heat To deactivate Auto heat-up When Auto heat-up has been activated, the burner automatically turns on at the highest setting (heat-up boost) and then switches to the previously selected continued power level. The heat-up time depends on which continued power level has been chosen (see chart). You can turn off the heat-up boost before the heat-up time has elapsed. With higher continued power levels, only a relatively short heat-up time is required.
Use Variable burner Two-zone burner With some cooktop models (see "Description of the appliance"), you can turn on a second or third burner zone when using larger pots. ^ Touch the On/Off touch control for the desired burner. If you add another burner zone, the indicator light will be on as long as the power level is flashing in the burner display. When the power level stops flashing and stays steady, the indicator light goes out.
Use Turning off and residual heat indicators To turn a burner off ^ Touch the On/Off touch control for the desired burner. ^ Touch "0" on the settings bar. A 0 flashes for a few seconds in the burner display. If the burner is still hot, the residual heat will be displayed. To turn the cooktop off ^ Touch the s touch control. This turns off all the burners. The power-ON indicator light goes out. The residual heat indicator will appear for each burner which is still hot.
Selecting cookware – Use cookware with thick, flat, smooth bottoms. Slightly concave bottoms will also work adequately. Pans with convex bottoms will not cook well. cold Energy saving tips – For the most even and energy efficient cooking, the diameter of the pots/pans should match the diameter of the burners as closely as possible. hot – Cast iron, glass or stoneware should not be used because they have poor heat transfer and may scratch the cooktop surface.
Timer The cooktop must be turned on to use the timer. The timer can be used for two different functions: – To time kitchen activities. – To set a burner to turn off automatically. You can select a time from 1 minute (01) to 9 hours (9^). A time up to 99 minutes is set and displayed in minutes. Example: With a time of more than 99 minutes, the timer must be turned to hours. The time is set in half-hour increments. The half hour is indicated by a dot after the number.
Timer Setting the timer Minutes Hours Example: You want to set a time of 15 minutes. To set full hours, touch the respective number on the settings bar. To set the half hours, touch the space between 2 numbers on the settings bar. Example: 2 hours and 30 minutes ^ Turn the cooktop on. ^ Touch the m control. 00 appears in the timer display, and the right 0 will flash. ^ Turn the cooktop on. ^ Touch the m control. 00 appears in the timer display, and the right 0 will flash.
Timer To change the set time ^ Touch the m control. ^ Set the desired time as described in "Setting the timer". To clear the set time ^ Touch and hold the m control until 00 appears in the timer display.
Timer Turning a burner off automatically You are able to set a time in which a burner turns off automatically. If desired, all of the burners can be programmed at the same time. If the programmed time is longer than the maximum time allowed, the burner will turn off automatically after the maximum time allowed (see "Safety cut-out feature"). ^ Select a power level for the desired burner. ^ Tap the m touch control until the indicator light for the burner starts flashing. The time counts down in minutes.
Timer Using both timer functions at the same time The kitchen timer and automatic shut-off functions can be used at the same time. If you have programmed one or more shut-off times and would also like to set the kitchen timer: Tap the m touch control until the indicator lights for the programmed burners come on steady and 00 appears in the timer display.
Safety features Child safety lock / System lock To activate the locks Your appliance is equipped with a safety lock to prevent the cooktop and the burners from accidentally being turned on or any settings changed. ^ Touch the $ control until the respective indicator light comes on. The Child safety lock can be activated when the cooktop is turned on. When the safety lock is activated, the cooktop has only limited functions: – The burner power levels and the timer settings cannot be changed.
Safety features Stop and Go To activate Stop and Go Your appliance has a Stop and Go feature which, when activated, reduces the power of all the activated burners to level 1. The burner power-levels and the timer setting cannot be changed, the cooktop can only be turned off. ^ Touch the control. When Stop and Go is deactivated, the cooking zones resume at the power level which was last set. If Stop and Go is not deactivated, the cooktop turns off after 1 hour.
Safety features Safety shut-off Safety shut-off if the touch controls are covered Safety shut-off for cooking times that are too long If a burner is heated for an unusually long period of time (see chart) at the same power level, the cooktop will turn itself off automatically and the residual heat indicator will appear.
Safety features Overheat protection Each burner is equipped with a temperature limiter. This feature automatically turns off the heating element before the glass ceramic surface becomes too hot. When the overheat protection is triggered, the heating element turns on and off even at the highest power level. Once the glass ceramic surface has cooled to a safe temperature the heating element will automatically turn back on.
Cleaning and Care Do not use a steam cleaner to clean this appliance. Steam could penetrate electrical components and cause a short circuit. Pressurized steam could cause permanent damage to the surface. Do not use any sharp pointed objects which could damage the seal between the ceramic surface, the surrounding frame and the countertop. Never use abrasive cleaners, caustic (oven) cleaners, dishwasher detergent, scouring pads, steel wool or hard brushes. They will damage the surface.
Programming The programming of your cooktop can be modified (see chart). After starting the programming function P (Program) and an S (Status) will appear in the timer display. With cooktops that have 3 burners, an additional display appears at the back left. The program is displayed in the front left and back left burner displays. Example: Program 03 = front left 0, back left 3 Program 14 = front left 1, back left 4 The status is displayed in the front right burner display.
Programming Program* P 00 P 02 P 04 P 05 P 06 * Status** Setting Demo mode and factory S default settings 0 Demo mode ON (after turning the burner on "dE" appears in the timer display for several seconds) S 1 Demo mode OFF S 9 Factory default settings restored S 0 9 power levels (1, 2, 3 ... to 9) S 1 17 power levels (1, 1., 2, 2., 3 ... to 9) If Auto-heat boost is selected, A will flash alternately with the continued power level.
Programming Program* P P P P P P P P 07 08 11 12 13 14 15 16 System lock Status** Setting S 0 Manual activation of the system lock S 1 Automatic activation of the system lock S 0 Off S 1 On Second burner zone of S the left front burner S 0 Does not turn on with the first zone 1 Always turns on with the first zone Second burner zone of S the right front burner S 0 Does not turn on with the first zone 1 Always turns on with the first zone Second burner zone of S the right back bur
Frequently asked questions ,Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. Cooktop or burners cannot be turned on Possible fault Solution The circuit breaker has tripped. Reset the circuit breaker (see the data plate for minimum breaker ratings). There may be a technical problem. – Disconnect the appliance from the main power supply for approx. 1 minute.
Frequently asked questions The cooktop turns off while in use, and a flashing F appears in the timer display. Possible fault Solution One or several of the touch controls are covered, for example by fingers, food boiling over or by an object. Clean the control panel or remove the object (see "Safety shut-off".) Auto-heat is turned on, but the food does not start cooking. Large amounts of food are being heated. Start cooking at the highest power level, then reduce the power level manually.
Frequently asked questions The sensor switches are hypersensitive or not sensitive enough. Possible fault Solution The sensitivity of the touch controls has changed. First, ensure that the cooktop is not in direct sunlight or strong artificial light and that the area around the cooktop is not too dark. Make sure that neither the cooktop or the touch controls are covered. Remove any cookware and clean the cooktop, removing any food residues. Disconnect the cooktop from the main power supply for approx.
Technical Service In the event of a fault which you cannot easily fix yourself, please contact the Miele Technical Service Department at the address on the back of this booklet. When contacting Technical Service please quote the serial number and model of the appliance. Adhere rating label sticker supplied with the appliance below.
Installation Instructions IMPORTANT: SAVE FOR THE LOCAL ELECTRICAL INSPECTOR'S USE Information is subject to change. Please refer to our website to obtain the most current product specification, technical & warranty information. To prevent accidents and appliance damage read these instructions before installation or use.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Note to the installer: Please leave this instruction book with the consumer for the local electrical inspector’s use. The minimum distances given in these Installation Instructions must be observed in order to ensure safe operation. Failure to do so increases the risk of fire. The cabinetry and venting hood should be installed first to prevent damage to the cooktop. ~ This appliance has not been designed for maritime (e.g.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Safety distance from divider Installation of a divider under the cooktop is not required. Safety distances above the appliance If a divider is fitted under the cooktop, the distance between the upper edge of the work surface and the upper edge of the divider must be at least 4 ½ " (110 mm). A gap of at least 1 3/8"" (35 mm) must be provided between the rear edge of the divider and the rear wall of the cabinet so that the power cord can be passed through.
IMPORTANT INSTALLATION SAFETY INSTRUCTIONS Safety distances to the sides of the appliance The appliance should only be installed as shown in the illustrations, while maintaining the required safety distances shown. Do not install the appliance between two tall cabinets, this is a fire hazard. not allowed a 1 5/8"" (40 mm) minimum distance from the countertop cut-out to the rear edge of countertop or wall.
Installation Safety distance from the wall covering If a wall covering is installed, a minimum safety distance must be maintained between the countertop cut-out and the covering, since high temperatures can damage these materials. If the covering is made of a combustible material (such as wood), the distance between the countertop cut-out and the wall covering must be a minimum of 2" (50 mm).
Installation Frame/Facet Cooktops Sealing The appliance must not be permanently sealed into the countertop when installed. The sealing strip under the edge of the appliance provides a sufficient seal for the countertop. If the appliance is sealed into position, the countertop or appliance could be damaged if it needs to be removed for maintenance or service.
Installation dimensions a Spring clips b Front c Installation height d Connecting cable, Length = 56 11/16" (1440 mm) e Rating label 43
Installation Wood or solid surface countertop The exact positions of the spring clamps and the support bars (for beveled cooktops only) are shown in the "Installation dimensions" of each unit. Facet cooktops: A special sealing strip ensures the slip-proof seating of the cooktop in the cutout. The gap between the frame and the countertop will narrow after a little time has passed. ^ Seal the cut surfaces with a suitable sealant to avoid swelling caused by moisture. The materials used must be heat resistant.
Installation Granite countertop Strong double-sided adhesive tape and silicon are required for installation (not included). ^ Coat the lateral edges and the lower edge of the spring clips and securing strips with silicon. ^ Using adhesive tape c attach the spring clips and the securing strips (for facet cooktops only) The spring clips and the securing strips must be on or flush with the top edge of the cooktop.
Installation Insert the cooktop ^ Feed the power cord down through the cut-out. ^ Place the cooktop lightly on the spring clips. ^ With a hand on each side of the appliance press down evenly on the edges until it clicks into position. When doing so make sure that the appliance seal sits tightly on the countertop to ensure it is sealed correctly. This is important to ensure an effective seal. Do not permanently seal into the countertop.
Electrical connection ,CAUTION: Before installation or servicing, disconnect the power supply by either removing the fuse, shutting off the main power or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held responsible.
Help protect our environment Disposal of packing materials Disposal of an old appliance The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Old appliances contain materials that can be recycled. Please contact your local recycling authority about the possibility of recycling these materials. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
Alteration rights reserved / 4210 M.-Nr. 07 844 700 / 01 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
