Operating instructions for Washing machine W 3744 To avoid the risk of accidents or damage to the machine it is essential to read these instructions before it is installed and used for the first time. en - GB M.-Nr.
Caring for our environment Disposal of the packing material Disposal of your old appliance or machine The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Electrical and electronic appliances / machines often contain materials which, if handled or disposed of incorrectly, could be potentially hazardous to human health and to the environment.
Contents Caring for our environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating the washing machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Before using for the first time. . . . . . . . . . . .
Contents Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 The correct detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Water softener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Washing with several components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Screwing out and adjusting the feet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Building under a continuous worktop/in a kitchen run . . . . . . . . . . . . . . . . . . . 48 Washer and Dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 The Miele water protection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Connection to the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning and Safety instructions This washing machine conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the washing machine, please read these instructions carefully before using it for the first time. They contain important information on its installation, safety, use and maintenance. Keep these instructions in a safe place and ensure that new users are familiar with the content.
Warning and Safety instructions Technical safety ~ Before setting up the washing machine, check it for any externally visible damage. Do not install or use a damaged washing machine. ~ Before connecting the washing machine, ensure that the connection data on the data plate (voltage and connected load) match the mains electricity supply. If in any doubt, consult a qualified electrician.
Warning and Safety instructions ~ This washing machine may only be used in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ Turn off the stopcock if the machine ~ Do not make any alterations to the If hooking the drain hose into a wash basin, check that the water can drain off quickly enough to prevent the sink from overflowing.
Warning and Safety instructions ~ Textiles which have been pre-treated in solvent based cleaning agents must be thoroughly rinsed in clean water before being washed in the machine. ~ Never use solvent based cleaning agents, e.g. those containing benzene, in this machine, as this may result in damage to component parts and create toxic fumes. Such agents also pose a fire and explosion hazard. ~ Never use solvent based cleaning agents, e.g.
Operating the washing machine Control panel a Extra option buttons Various extra options can be added to the washing programmes. b Display See the following page for more information. c Temperature button For selecting a temperature. d Spin speed button For selecting the final spin speed or e (Rinse hold) or deselecting the spin (No u). e PC / Optical interface This is used by service technicians to run diagnostic checks on your machine and can also be used to update programming data in the future.
Operating the washing machine Programme duration After the start of a programme, the estimated programme duration will appear in the display in hours and minutes. The following are selected via the display: – wash temperature – spin speed – programmable functions – cancellation of a programme During the first 8 minutes the washing machine measures how much water is being absorbed by the laundry and uses this to calculate the load.
Before using for the first time Setting the language Before using the machine for the first time ensure that it is correctly installed and connected. See "Installation and connection". Also check that the drain filter is securely tightened to prevent the risk of water leaks during use. This washing machine has undergone a thorough functional test in the factory and there will be some residual water in the drum from this process.
Washing environmentally and economically Energy and water consumption Detergent – Water consumption and energy usage are determined by the size of the load. To make the most out of your machine, load the maximum dry load for the programme you are using. – Do not exceed the amounts of detergent recommended by the manufacturer on the packaging. – Use the Automatic and Express programmes for small loads.
How to wash correctly Brief instructions The headings numbered A, B, C, . . . show the operating sequence and can be used as brief instructions. A Sort the laundry ,If you use a solvent-based clean- ing agent (e.g. one containing benzene) to pre-treat a stain, make sure that any plastic parts (e.g. buttons) are protected, and that the cleaning agent is rinsed off before washing the garment in the machine. ,Do not use solvent-based cleaning agents in this machine.
How to wash correctly B Switch on the washing machine D Select a programme C Load the drum ^ Press the Door button to open the drum door. ^ Unfold the laundry and load loosely in the drum. Mixing both large and small items gives better wash results and also helps distribute the load evenly during spinning. The most efficient use of energy and water is achieved when a full load is washed. However, do not overload as this causes creases and reduces cleaning efficiency.
How to wash correctly F Select an extra option(s) Water plus The water level in the main wash and the rinses will be increased if the Water plus option is selected. However, you can select other settings for Water plus. These are described in "Programmable functions". Pre-wash For laundry with large amounts of dirt e.g. dust, sand. ^ Select any extra options by pressing the appropriate button. The relevant indicator light will come on to show which extra option has been selected.
How to wash correctly G Add detergent It is important to dispense the correct amount, because . . . . . . too little detergent results in: – Laundry not getting properly clean and with time it may become grey and hard to the touch. – Greasy particles clinging to the laundry. – Limescale deposits on the heater elements. . . . too much detergent results in: – Excessive foam which causes a low level of agitation and poor wash, rinse and spin results.
How to wash correctly H Start the programme ^ Press the flashing Start/Stop button. The estimated programme duration will appear in the display once the programme has started. During the first 8 minutes the machine measures how much water is being absorbed by the laundry. The programme duration may be longer or shorter depending on this absorbency rate. Check that all items have been removed from the drum. Items left in the drum could discolour other items in the next wash or become discoloured themselves.
Spinning Final spin speed Programme To omit the final spin (Rinse hold) rpm Cottons 1600 Minimum iron 1200 Delicates 600 Woollens 1200 Silks 400 Express 1600 Automatic 1200 Shirts 600 Denim 900 Outerwear 800 Dark garments 1200 Spin 1600 You can reduce the final spin speed. However, you cannot select a final spin speed higher than that shown in the chart above. Rinse and interim spin There is a spin after the main wash and between the rinses.
Programme chart Cottons 9ö8E76* Fabric 30°C to 95°C Max. load 6.0 kg Cottons, linens or cotton mix fabrics, e.g. table linen, towelling, underwear, T-shirts etc. Extra options Short, Water plus, Pre-wash Note for test institutes: Short programme: 3.0 kg load and Short extra option Minimum iron 43218E76* 30°C to 60°C Max. load 3.0 kg Fabric Synthetics, mixed fibres and easy care cottons. If fabrics have a high proportion of man-made fibres it is advisable to programme the machine for "Gentle action".
Programme chart Silks /c* cold to 30°C Max. load 1.0 kg Fabric Silks and other handwashable fabrics with no wool content, e.g. satin, lace and silk. Note Place tights, bras etc. in a washing bag. Extra option Water plus Express 76* cold to 40°C Max. load 3.0 kg Fabric Small loads of items which require freshening up and which can be washed in a Cottons programme. Note This programme can be used for rinsing individual items. Select the cold setting, and do not add any detergent.
Programme chart Outerwear cold to 40°C Max. load 2.0 kg Garment Outerwear made from micro-fibres such as Gore-Tex®, SYMPATEX®, WINDSTOPPER® etc. Notes – Zip up jackets before washing. – Do not use fabric conditioner. Extra options Short, Water plus, Pre-wash Dark garments cold to 40°C Max. load 3.0 kg Item Black and dark garments made from cotton or mixed fibres. Note Wash inside out. Extra option Short Spin Notes – Drain only: Select No u. – Make sure you select the appropriate spin speed.
Programme sequence Main wash Rinses Spinning Water level Wash rhythm Water level Rinses Interim spin Final spin Cottons d a ( 2-41) L L Minimum iron ( c e 2-32) L L Delicates e d e 3 – L Woollens e e e 2 L L Silks e e e 2 Express d b Automatic ( Shirts – L d 2-3 2) L L abc e 2-32) L L e c e 2 – L Denim ( c e 3 – L Outerwear e d e 3 L L Dark garments ( b d 3 L L – – – – – L Spin d = Low water level ( = Medium water
Programme sequence This machine has fully electronic controls with automatic load recognition. It takes in the right amount of water required for the programme depending on the amount of laundry and its absorbency rate. This means that programme cycles and durations can vary. The programme sequences outlined in the chart are based on the basic programme with a full load. Extra options which can be selected have not been taken into account.
Garment care label symbols Washing The figure quoted in the bucket is the maximum temperature the garment can be washed at. The number of bars under the symbol indicates the level of agitation permitted.
Changing the programme sequence Cancelling a programme Changing a programme You can cancel a programme at any time after it has started. After the start of a programme it is no longer possible to select a different programme. ^ Press the Start/Stop button. Cancel programme Temperature ^ Press the flashing Start/Stop button again. It is possible to select a different temperature up to 5 minutes after the programme has started. The suds will be pumped away.
Changing the programme sequence Adding or removing laundry after a programme has started ^ Press the Door button to open the drum door. ^ Add or remove items. Safety lock The safety lock prevents the machine from being opened and programmes from being cancelled during a wash programme. ^ Close the drum door. To activate the safety lock The programme will continue automatically. ^ Press and hold in the Start/Stop button after the programme has started.
Detergent The correct detergent All modern detergents produced for automatic washing machines are suitable. Use dispensing aids, e.g. balls, if these are supplied with the detergent. Tablets are suitable for full loads, but note that it may be impractical to reduce tablets for smaller loads. Some tablets do not dissolve as rapidly as others, and may not be suitable for programmes with short durations. Do not use biological detergents on silk, as the enzymes may damage the silk.
Detergent The right amount to dispense will depend on the following: – The quantity of laundry – The soiling level of the laundry Lightly soiled No visible dirt or stains. Possibly slight body odour. Normally soiled Visibly dirty and/or just a few slight stains. Heavily soiled Visible dirt and stains and/or dried on soiling. – The water hardness level. Check with your local water supplier if you do not know the hardness level in your area.
Detergent Fabric conditioners and liquid starch Fabric conditioners make garments soft to handle and help prevent static cling when tumble drying. Starch stiffens and gives body to items of laundry, e.g. shirts, tablecloths and bed linen. Automatic dispensing of fabric conditioner or liquid starch to laundry at the end of a programme If starching frequently, thoroughly clean the dispenser compartment, especially the siphon tube and the fabric conditioner channel, regularly.
Cleaning and care ,Disconnect the machine from the mains electricity supply and withdraw the plug from the socket before cleaning the machine. ,The washing machine must not be hosed down. A range of Miele branded cleaning and conditioning agents are available to order from your Miele dealer, the Miele Spare Parts Department, or via the internet on www.miele-shop.com External casing and fascia panel Extra cleaning Carry out a hot wash (70°C or above) with powder detergent approx.
Cleaning and care Cleaning the detergent dispenser drawer housing ^ Clean the siphon. 1. Remove the siphon from compartment § and rinse under warm running water. Clean the siphon tube in the same way. 2. Replace the siphon. If starching frequently, thoroughly clean the siphon and siphon tube regularly. A build-up of starch will cause them to get clogged. 32 ^ Use a bottle brush to remove detergent residues and limescale from the jets inside the detergent dispenser drawer housing.
Cleaning and care Cleaning the water inlet filters The washing machine has two filters to protect the inlet valves. These filters should be checked every six months or so, or more often if there are frequent interruptions to the water supply. To clean the filter in the water inlet valve: ^ Using pliers, carefully loosen the ribbed plastic nut on the inlet valve and unscrew. To clean the filter in the union in the open end of the inlet hose: ^ First turn off the stopcock.
Problem solving guide With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting the Service Department. ,Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous.
Problem solving guide Fault messages in the display Problem ; lights up in the display and Drain fault flashes. ; lights up in the display and Water inlet fault Possible cause – The water outlet is – Clean the drain filter and blocked or the drain pump. restricted. – The maximum delivery head is 1 m. – The drain hose has been fixed too high. – The water inlet is blocked or restricted. Check whether – the stopcock is opened properly. – the inlet hose is kinked. – the water pressure is too low.
Problem solving guide General problems Problem The machine shakes during the spin cycle. Possible cause The machine feet are not level. Remedy Level the machine (see "Installation"). The laundry has not been The machine detected an spun properly and is still imbalance during the final wet. spin and reduced the spin speed automatically. Include both large and small items in the load as this will give better distribution. The laundry has not spun The spin speed selected satisfactorily. was too low.
Problem solving guide An unsatisfactory wash result Problem Possible cause Remedy Liquid detergent does not give the required result. Liquid detergents usually contain no bleaching agents. They do not remove fruit, coffee and tea stains. Grey, greasy particles cling to washed laundry. Insufficient amounts of – Use more detergent. detergent were used – Before washing the next load to break down the run a Cottons 95°C programme particles of grease in with powder detergent but heavily soiled laundry.
Problem solving guide The drum door does not open when you press the Door button Possible cause Remedy The machine is not Insert the plug in the socket and switch on and/or connected to the switch the machine on with the I-On/0-Off button. electricity supply and/or is not switched on. The safety lock has been activated. Deactivate the safety lock as described in "Changing the programme sequence - Safety lock". Access via a code has been activated.
Problem solving guide Opening the drum door in the event of a blocked drain outlet and/or power failure ^ Switch the washing machine off. There is a lever behind the detergent drawer fascia panel. Blocked drain outlet If the drain outlet is blocked, up to 25 litres of water will be retained in the machine. ,Caution: if laundry has been washed at a high temperature, water draining out of the machine will still be hot.
Problem solving guide Once the flow of water ceases: ,Make sure the drain filter is securely tightened. Otherwise there is a risk of water leakage during use. Opening the drum door ,Always make sure that the drum is stationary before reaching into the machine to remove laundry. Reaching into a moving drum is extremely dangerous. ^ Remove the drain filter completely. ^ Clean it thoroughly. ^ Pull the emergency release downwards (see illustration). The drum door will open.
After sales service In the event of any faults which you cannot remedy yourself, please contact: – your Miele Dealer or – the Miele Customer Contact Centre (see back cover for contact details). When contacting your Dealer or Miele, please quote the model and serial number of your machine, both of which are shown on the data plate visible above the porthole glass when the door is open.
Installation and connection Front view a Inlet hose (tested to withstand pressure of at least 7,000 kPa) b Electricity supply cable c - f Flexible drain hose (with detachable swivel elbow) g Control panel h Detergent dispenser drawer i Drum door j Access to drain filter, drain pump and emergency release k Handle recesses for moving the machine l Four height adjustable feet 42
Installation and connection Rear view a Protruding lid for holding when moving the machine e Transit bar covers b Electricity supply cable f Restraining clip for inlet hose and drain hose c Inlet hose (tested to withstand pressure of at least 7,000 kPa) g Restraining clips for transit bars when removed d Drain hose 43
Installation and connection Installation surface Installing the washing machine A concrete floor is the most suitable installation surface for a washing machine, being far less prone to vibration during the spin cycle than wooden floorboards or a carpeted surface. To manoeuvre the machine out of its packing case to its installation site hold it by the edge of the lid where it protrudes to the rear of the washing machine as well as by the handle recesses at the front.
Installation and connection ^ Using the spanner supplied turn the left-hand transit bar 90°, then ^ Turn the right-hand transit bar 90°, then ^ withdraw the transit bar. ^ withdraw the transit bar.
Installation and connection ,To avoid the risk of injury the holes for the transit bars must be covered after the transit bars have been removed. ^ Secure the transit bars to the back of the washing machine. Make sure that holes b are fitted over retainers a. ,The washing machine must not ^ Fit the covers on to the two holes. Then plug the holes as shown with the caps. be moved without the transit bars in place. Store the transit bars as shown or keep them in a safe place for future use.
Installation and connection Levelling the machine The machine must stand perfectly level on all four feet to ensure safe and proper operation. Incorrect installation may increase electricity and water consumption and may cause the machine to move about. Screwing out and adjusting the feet The four adjustable screw feet are used to level the machine. All four feet are screwed in when the machine is delivered. ^ Use a spirit level to check the machine is standing level.
Installation and connection Washer and Dryer stack The fitting of building under kits and stacking kits must only be undertaken by qualified and competent persons, in accordance with the instructions supplied with the kit. Building under a continuous worktop/in a kitchen run A Miele tumble dryer can be stacked with the washing machine. A "WTV" stacking kit* is necessary and can be purchased from the Miele Spare Parts Department or via the internet at www.miele-shop.com.
Installation and connection The Miele water protection system The Miele water protection system protects the washing machine from water damage. The system consists of three main components: 1) the inlet hose 2) the electronic unit and the washing machine housing 3) the drain hose – Overflow protection This prevents the washing machine taking in too much water. If the water level exceeds a certain level, the drain pump switches in and pumps the excess water away.
Installation and connection Connection to the water supply The machine should be connected to a mains water supply in accordance with local and national safety regulations. The German authorities do not require it to have a non-return valve as the washing machine has been designed to comply with DIN regulations. The machine is designed to operate with a flow pressure of between 100 kPa and 1,000 kPa. If it is higher than 1,000 kPa it is essential to fit a pressure reducing valve.
Installation and connection Connection to the drainage system Please note: The machine drains via a drain pump with a delivery head of 1 metre*. The drain hose must not be kinked as this restricts drainage. The swivel elbow at the end of the hose can be turned in either direction, or can be detached if required, with a sharp twist and pull. If required, the drain hose can be extended to a length of 5 m. The necessary parts can purchased from the Miele Spare Parts Department or your Miele dealer.
Installation and connection Electrical connection U.K. Non-rewireable plugs BS 1363 All electrical work should be carried out by a suitably qualified and competent person, in strict accordance with current national and local safety regulations (BS 7671 in the UK). The fuse cover must be refitted when changing the fuse, and if the fuse cover is lost, the plug must not be used until a suitable replacement is obtained.
Consumption data Load Cottons Energy Water in kWh in litres Duration Short Normal 95°C 6.0 kg 1.99 47 2 h 09 min 60°C1) 6.0 kg 1.02 47 1 h 49 min 60°C 3.0 kg 0.73 39 40°C1) 6.0 kg 0.65 59 2) 3.0 kg 0.36 39 59 min 40°C1) 3.0 kg 0.50 55 59 min 40°C Minimum iron Consumption data 1 h 02 min 2 h 04 min 49 min 1 h 19 min Delicates 30°C 2.0 kg 0.35 69 Woollens / 30°C 2.0 kg 0.23 39 – 39 min 59 min Silks / 30°C 1.0 kg 0.25 39 – 36 min Express 40°C 3.
Technical data Height 850 mm Width 595 mm Depth 580 mm Depth with door open 975 mm Height for building under 820 mm Width for building under 600 mm Depth for building under 600 mm Weight 93 kg Maximum floor load 1,600 Newton (approx. 160 kg) Capacity 6 kg dry laundry Voltage see data plate Connected load see data plate Fuse rating (UK) see data plate / plug Consumption data see "Consumption data" Water flow pressure min. 100 kPa (1 bar) Water flow pressure max.
Programmable functions for changing default settings The programmable functions are used to alter the machine's electronics to suit changing requirements. Programmable functions can be altered at any time.
Programmable functions To access programmable functions The programmable functions are accessed via the Start/Stop button and the programme selector. Before you begin, first ensure that: – The washing machine is switched off. – The machine is properly closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. B Press the I-On/0-Off button in. C As soon as . . . Language !... . . . appears in the display, release the Start/Stop button.
Programmable functions Water plus This programmable function is used to select the water intake setting for the Water plus extra option. There are three different options: Water + (the machine is delivered with this option selected) The water level is increased in the wash and rinse stages. Extra rinse An extra rinse is introduced. Water+ & Extra rinse The water intake is increased in the wash and rinse stages and an additional rinse is also introduced.
Programmable functions Code A code can be used to lock the electronics on the washing machine to prevent it being used without your knowledge. When the code has been activated, you have to enter a code after switching the washing machine on. Otherwise the washing machine cannot be operated. Code ... 1 2 5 ^ Press the Start/Stop button. The following will appear in the display: Code activated Once the machine is switched off, it can only be used again if the code is entered.
Programmable functions Temperature unit You can chose for the temperature to be displayed as °C/Celsius or °F/Fahrenheit. The machine is delivered with °C/Celsius as the default setting. Keypad tone An audible tone sounds each time a button is pressed. The machine is delivered with the keypad tone deactivated. Brightness Buzzer When the buzzer function has been activated, an audible tone sounds at the end of a programme or when Rinse hold is reached.
Programmable functions Standby display To save energy, the display goes out and the indicator light for the Start/Stop button will start flashing slowly. The display will always go out, – if a programme is not selected within 10 minutes of the machine being switched on. – 10 minutes after the end of a programme. Pressing one of the buttons switches the display back on again.
Optional accessories Miele washing machines offer perfect care for your laundry and feature a wide range of special programmes designed to suit the fabric being washed. And now Miele have developed a range of specialist CareCollection detergents and conditioning products to offer you a complete package for cleaning and caring for your laundry. The Miele CareCollection detergents and conditioning products are listed below.
Optional accessories "UltraWhite" detergent Liquid detergent "For Delicates" This multi-purpose powder detergent has excellent stain removal properties and is suitable for white and light coloured laundry as well as heavily soiled coloured items. This liquid detergent is ideal for the gentle treatment of delicate fabrics, such as wool and silk. Its special formulation cleans effectively at temperatures as low as 20°C, while protecting the colour of your delicate garments.
Alteration rights reserved/0309/W 3744 M.-Nr.
