Operating Instructions Heat-pump Dryer It is essential to read these operating instructions before installing, starting up, and using the appliance. This prevents both personal injury and damage to the appliance. en-US M.-Nr.
Contents Caring for the environment ................................................................................. 6 IMPORTANT SAFETY INSTRUCTIONS ................................................................ 7 Operating the tumble dryer ................................................................................ Control panel ......................................................................................................... Operating the sensor buttons.......................................
Contents Extra options........................................................................................................ Gentle .................................................................................................................... Freshen-up ............................................................................................................ Anti-Crease............................................................................................................ Buzzer...............
Contents Technical Service................................................................................................. Contact in case of fault ......................................................................................... Warranty ................................................................................................................ Optional accessories.............................................................................................
Contents Settings ................................................................................................................ Calling up settings................................................................................................. Language ......................................................................................................... Drying levels .......................................................................................................... Welcome tone ...........
Caring for the environment Disposal of packaging material Disposal of your old appliance The packaging material protects the dryer from transport damage. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances contain valuable materials. They also contain certain substances, compounds and components which were essential for the proper functioning and safe use of the equipment.
IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: WARNING This tumble dryer is intended for use in domestic households and similar working and residential environments. It is essential to read all instructions before using the appliance. Do not allow children to play on or in the appliance. Close supervision is necessary when the appliance is used near children.
IMPORTANT SAFETY INSTRUCTIONS Important information regarding use of fabric softener sheets: We do not recommend use of fabric softener sheets. Use of fabric softener sheets can clog the surfaces of the lint filters, extending the drying time and increasing energy consumption. During subsequent cleaning, the plastic and surfaces of the lint filters can be damaged! The best results are obtained by using liquid fabric softener in the washing machine. Follow the manufacturer's instructions.
IMPORTANT SAFETY INSTRUCTIONS To prevent the risk of fire, the following textiles must not be dried in this dryer: – items which have not been washed. – items, such as work-wear, exposed to grease, oils, or other deposits (such as lotions or cosmetics) in your dryer. If these items have not been thoroughly cleaned there is a danger that they may contribute to a chemical reaction that could cause the laundry to ignite when heated even after being removed from the dryer.
IMPORTANT SAFETY INSTRUCTIONS Allow the dryer to complete each stage of the program selected, including the cooling down phase. This will ensure that the items being removed are not too hot to handle. Clean the lint filter before or after each load. Keep the area around the air intake (toe kick) and adjacent surrounding areas free from lint, dust and dirt. The interior of the machine should be cleaned periodically by qualified personnel. GROUNDING INSTRUCTIONS This appliance must be grounded.
IMPORTANT SAFETY INSTRUCTIONS Do not modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Before installation, disconnect the tumble dryer from the electrical supply by shutting off the power main, unplugging the power cord or tripping the circuit breaker. Do not restore power until the installation is complete. Miele tumble dryers and Miele washing machines can be installed as a washer-dryer stack.
IMPORTANT SAFETY INSTRUCTIONS Heat pump technology and refrigerant: The heat pump in this tumble dryer uses a gaseous refrigerant which is condensed by the compressor. The refrigerant, which is brought to a higher temperature level and liquified by condensing, is led in a closed circuit through the heat exchanger unit where heat exchange with the circulating drying air takes place. After installation, downtime of 1 hour is required before connecting the tumble dryer to the electricity supply.
IMPORTANT SAFETY INSTRUCTIONS Using a fragrance capsule (optional accessory) Only use genuine Miele original fragrance capsules. Store the fragrance capsule in its original packaging. Caution: The fragrance can leak out of the capsule! Make sure that you always keep the capsule, or the lint filter with the capsule inserted in it, in a horizontal position when carrying and do not tip or place it down on any surface.
IMPORTANT SAFETY INSTRUCTIONS FCC Declaration of Conformity This appliance complies with Part 15 of the FCC regulations. This appliance has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and is subject to the following conditions: This appliance does not cause harmful interference. The appliances may be interconnected as desired.
Operating the tumble dryer Control panel a Control field The control field consists of a display and various sensor buttons. The individual sensor buttons are explained in the following sections. b Display The following values are displayed and/or selected on the display: 1. The program names, the drying level, and the duration of the selected program 2. The individual values of the selection lists for the settings c Sensor buttons The values in the display can be changed with the sensor buttons.
Operating the tumble dryer f Optical interface This is used by Miele service technicians as a transmission point. g Sensor buttons for extra options You can select extra options to augment the wash programs. If a drying program has been selected, the sensor buttons for the possible extra options light up dimly. h Sensor button You can use the sensor button to call up an energy consumption forecast for the selected drying program. i Sensor buttons The sensor button starts the delay start function.
Operating the tumble dryer Identifying the selected option Display The basic display shows the following for a drying level program: On Normal OK 0:55 OK – The selected drying level and the expected program duration Setting numerical values – The drying level reached after the start of the program and the remaining program duration The basic display shows only the program duration for a time-controlled program: 2:00 An option which has been activated will have a tick next to i
Energy saving tips This dryer is designed for energysaving drying cycles thanks to its heat pump technology. However, you can save a little more energy with the following measures as the drying time is not extended unnecessarily. – Make sure your laundry is spun at the maximum spin speed before drying. The higher the spin speed, the greater the savings that can be made in energy and time during drying, e.g., approx. 20 % energy can be saved if spun at 1600 rpm instead of 1000 rpm.
Functioning of the heat-pump dryer Two separate circuits ensure that the laundry is dried: Dry air circuit The drying air flows through a heat exchanger, the drum, and several filters. This is ensured by a blower in the dryer. – The drying air flows through the heat exchanger in the longitudinal direction and is heated in the rear area. – The drying air is then blown into the drum, where it absorbs the moisture of the laundry.
Initial set-up Downtime after installation After installation, downtime of 1 hour is required before connecting the tumble dryer to the electricity supply. Otherwise, the heat pump could be damaged. Removing the protective foil and stickers Remove: – The protective foil from the door – Any stickers from the front and the lid Please do not remove any labels (e.g., the data plate) which are visible when you open the door.
Initial set-up Miele@mobile App Setting up Miele@home Your tumble dryer is equipped with an integrated WiFi module. The dryer can be connected to the household WiFi network. The Miele@mobile App is available to download free of charge from the Apple ® App Store or from the Google Play Store™. You will then be able to operate the dryer via the Miele@mobile app. The following message appears in the display: Miele@home Touch the OK sensor button.
Initial set-up Connecting via the app The Miele@mobile app can be used to connect to your network. Install the Miele@mobile app on your mobile device. Follow the instructions in the app. To log in you will need: Completing the procedure for initial set-up outlined in these instructions Confirm with the OK sensor button. Please see “1. Notes on correct laundry care”. 2. The password for your tumble dryer You can then select a program and load the tumble dryer as described in “2.
1. Notes on correct laundry care Points to note regarding washed laundry – When washing very heavily soiled items, ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times. – Do not load the drum with items that are still soaking wet. Make sure your laundry is spun at the maximum spin speed before drying. The higher the spin speed, the greater the savings that can be made in energy and time during drying.
1. Notes on correct laundry care Garment care label symbols Drying Normal/higher temperature Reduced temperature: select Gentle (for delicate textiles) Do not tumble dry Ironing Very hot Hot Warm Do not iron Laundry care when drying in a tumble dryer See the “Program chart”. This describes the programs and gives their maximum load. – Always observe the maximum recommended load for each program. This will mean that the energy consumption for the amount of laundry is at its most economical.
2. Selecting a program Switching on the tumble dryer Selecting a program The tumble dryer is switched on when you select a program, and switched off by turning the program selector to the position. There are three possible ways to select a program. Turn the program selector to a program. 1.
2. Selecting a program 2. Selecting further programs via the “More programs/” position and the display: 3. Selecting the programs via the MobileControl and the Miele@mobile app Tip: In order to use MobileControl , the dryer must be logged on to the WiFi network and remote control must be switched on. Turn the program selector. The following appears in the display: Time Dry OK Touch the sensor buttons until the program you want appears in the display.
3. Loading the tumble dryer Please see “1. Notes on correct laundry care” first. This prevents damage to textiles or the dryer. Opening the door If you are not using a fragrance capsule: The tab must be pushed down completely (see arrow). Closing the door Pull the door open at the side with the orange marker. Unfold the laundry and load loosely into the drum. Do not overload the drum.
4. Selecting program settings Program settings Time-controlled and other programs Programs with drying levels Time Dry, Cold Air, Basket Normal, Wrinkle-free, Delicates, Smoothing, Dress Shirts, Express, Denims, Outdoor, Sportswear, Table Linens/Drapes, Bed Linens The pre-set drying level can be changed if required. You can change the duration in 10minute increments.
4. Selecting program settings Delay start/SmartStart Selecting an extra option Gentle Freshen up Anti-crease Buzzer Delay start With the delay start function, you can delay the start of the program. Touch a sensor button to select the desired extra option. The relevant sensor button will light up brightly. Freshen up and Gentle cannot be combined, see “Extra options” for additional notes. This function is active when the setting SmartGrid is switched off.
4. Selecting program settings If desired, change the specified time and confirm with the OK sensor button. Canceling delay start The selected delay start time can be canceled before the program start. Touch the sensor button. The selected delay start time will appear in the display. Set a time value of 00:00 h with the sensor buttons. Confirm with the OK sensor button. The selected delay start time has been canceled.
5. Starting a program Starting a program Touch the flashing Start/Stop sensor button. The Start/Stop sensor button will light up and Drying appears in the display. Notes If a delay start time has been selected, then this will count down in the time display. At the end of the delay start time or immediately after the program has started (if no delay start time has been selected), the program duration will appear in the time display.
6. Program end – removing the laundry Program end The program is finished when End/AntiCrease or End appears in the display. The Start/Stop button light goes out. Remove the lint from the 2 lint filters in the door opening: see the “Cleaning and care – Lint filters”. You must remove the fragrance capsule (if present) beforehand. See “Fragrance capsule”.
Program chart All weights marked with * are based on the weight of dry laundry. Normal Full load (17.6 lb/8 kg)* Extra dry, Normal plus, Normal, Slightly dry Items Single and multi-layered cotton items. For example, T-Shirts, underwear, baby clothes, workwear, jackets, covers, aprons, overalls, hand towels, bath towels, bathrobes, and flannelette/bed linen. Tip – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for jersey fabrics (e.g.
Program chart Smoothing Very small load (2.2 lb/1 kg)* Normal, Hand iron Items – Cotton and linen fabric. – For minimum iron items made of cotton, mixed, or synthetic fiber. For example, pants, jackets, and shirts. Tip – This program smoothes out creasing caused during the spin cycle in the washing machine. – This program is also suitable for dry fabrics. – Please remove the garments as soon as the program has finished. Woolens/Silks Items Small load (4.
Program chart Denims Small load (6.6 lb/3 kg)* Normal plus, Normal, Slightly dry, Hand iron, Hand iron Items All the denim garments, e.g., jackets, jeans, shirts, and skirts. Outdoor Small load (5.5 lb/2.5 kg)* Normal, Hand iron Items Outdoor which is suitable for drying in a tumble dryer. Time Dry Items Full load (17.6 lb/8 kg)* – For multi-layered fabric whose layers have different drying characteristics, e.g., jackets, pillows, sleeping bags, and other voluminous items.
Program chart Basket Note Load for basket (7.7 lb/3.5 kg) – This program may only be used with the Miele dryer basket (optional accessory). – You must follow the operating instructions for the dryer basket. Fabric – You must follow the operating instructions for the dryer basket. type/Items – Only use this program to dry or air items which are suitable for drying in a tumble dryer but should not be physically tumbled. – Do not place shoes inside the drum for drying.
Extra options The drying programs can be augmented with various extra options. However, Freshen up and Gentle cannot be combined. Gentle Freshen up Anti-crease Buzzer Anti-Crease After the program has finished, the drum will continue to rotate in a certain rhythm for 2 hours, depending on the selected program. This “Anti-crease rhythm” helps to prevent creasing, if the laundry is not removed immediately after the end of a program. Buzzer Gentle Delicate fabrics (with the symbol on the care label, e.
Extra options Selectable extra options These extra options can be selected in addition to the program.
Changing the program sequence You cannot change to another program once a program has started (this prevents unintentional alterations). If you try to change a program, Change not possible lights up until the original program is reset. Exception: The dryer is switched off by turning the program selector to the position. You will need to cancel the current program before you can select a new one. Canceling a program Touch the Start/Stop sensor button. Cancel Program lights up.
Condensed water container Emptying the condensed water container The condensed water is collected in the condensed water container. Empty the condensed water container after every drying program. The Empty container See indicator will light up if the maximum level of the condensed water container is reached. To turn the indicator light off: open and close the door while the dryer is switched on. Empty the condensed water container. Replace the condensed water container in the dryer.
Fragrance capsule Using a fragrance capsule (optional accessory) will add a pleasant fragrance to your laundry. If you are not using a fragrance capsule: the cover must always remain closed (push the cover down completely with the tab). Before using a fragrance capsule, please read “Important safety instructions – Using a fragrance capsule (optional accessory)”. Inserting a fragrance capsule Only hold the fragrance capsule as illustrated.
Fragrance capsule Markers and must line up with one another. – You will feel a slight resistance and hear a soft click. Marker must be in position : this is the position at which you can feel a resistance. Turn the outer ring clockwise a little.
Fragrance capsule Before drying After drying You can select the intensity of the fragrance. To avoid the fragrance escaping needlessly: Turn the outer ring clockwise a little. Turn the outer ring counterclockwise until marker b is in position _. The further you open the capsule, the more intense the fragrance. Damp laundry and longer drying durations with sufficient heat transfer are needed for the fragrance to be released into the laundry effectively.
Fragrance capsule Replacing the fragrance capsule When the fragrance is no longer sufficiently intense: Never lay the fragrance capsule down on any surface as the fragrance will run out. Turn the outer ring counterclockwise until markers a and b line up. Replace the fragrance capsule with a new one. Fragrance capsules are available to order from Miele dealers or online.
Fragrance capsule Only store the fragrance capsule in its original packaging To prevent any fragrance running out of the capsule: When not in use, the fragrance capsule must only be stored in its original packaging as illustrated. Clean the lint filters and the plinth filter: see “Cleaning and care”. – When storing the fragrance capsule in its original packaging while you are not using it, e.g.
Cleaning and care Lint filters This tumble dryer has 2 lint filters in the door opening: the upper and lower lint filters trap lint produced during the drying process. Clean the lint filters after each drying program. This prevents an extension of the program duration. Also clean the lint filters when lights up. To turn the indicator light off: Switch the dryer off and then on again / if necessary, confirm with OK. Clean plinth filter. See Pull the upper lint filter forward to remove it.
Cleaning and care Cleaning the lint filters and air flow openings thoroughly If the drying duration has become longer or the surface of the filters is visibly compacted with lint, you should carry out the following cleaning procedure. You must remove the fragrance capsule (if present) beforehand. See “Fragrance capsule”. Remove the lint (see arrows) from the filter surface of all the lint filters and the perforated laundry deflector. Pull the upper lint filter forward to remove it.
Cleaning and care Cleaning the lint filters with water Wipe the smooth plastic surfaces of the lint filters with a damp cloth to clean them. Flush the lint filters through with warm running water. Shake the lint filters thoroughly and then dry them carefully. Ensure the filters are dry before Hold the dial and pull the lint filter forward to remove it. replacing them. Wet filters could cause operational faults. Push the lower lint filter in completely and lock it with the yellow dial.
Cleaning and care Cleaning instructions when using fabric softener sheets If you are using fabric softener sheets, please follow these warnings and instructions. Option 3 Wet the surfaces of the lint filters with a liquid color detergent (e.g., Miele Ultra Color Liquid Laundry Detergent). Leave it on for approx. 2 hours. First, clean the filters as Risk of fire! described in “Cleaning the lint filters with water”.
Cleaning and care Plinth filter Removing the plinth filter Clean the plinth filter whenever the Clean plinth filter. See lights up or when the program duration is longer than usual. To turn the indicator light off: Switch the dryer off and then on again / if necessary, confirm with OK. Press the round, indented area on the heat exchanger access panel to open it. The panel will spring open. Pull the plinth filter out by the handle. This causes the right-hand guide pin in the dryer to come out.
Cleaning and care Cleaning Cleaning the plinth filter flap Pull the handle out of the plinth filter. You can brush off a heavy build-up of lint on the plinth filter or remove it with a vacuum cleaner. Use a damp cloth to remove any lint. Make sure that you do not damage the rubber seal when doing this. Clean the plinth filter thoroughly under clear, running water. Check whether the cooling fins are blocked with lint (as follows).
Cleaning and care Checking the heat exchanger unit Replacing the plinth filter Danger of injury! Do not touch the cooling fins with your hands. You could cut yourself. Look to see if lint has accumulated. If there is visible soiling: Use a vacuum cleaner with a dusting brush attached to clean the cooling fins. Only pass the vacuum cleaner brush over them lightly, without applying any pressure. Take care not to bend the cooling fins out of shape or to damage them.
Cleaning and care The dryer can only be operated with the plinth filter fitted correctly and the heat exchanger access panel closed. The access panel must be closed correctly to ensure that water cannot leak from the condenser system and to ensure that the dryer functions efficiently. Tumble dryer Disconnect the tumble dryer from the electrical supply. Do not use any solvents, abrasive cleaners, glass cleaners, or all-purpose cleaners. These could damage plastic surfaces and other parts.
Frequently Asked Questions With the help of the following guide minor faults in the performance of the machine, some of which may result from incorrect operation, can be remedied without contacting the Service Department. Time and money will be saved because a service call will not be needed. This guide may help you to find the reason for the fault, and how to correct it. Some of the messages in the display are more than one line long. Touch the or sensor button to read them in full.
Frequently Asked Questions Message Possible cause and solution The condensed water container is full or there is a lights up after kink in the drain hose. Empty out the condensed water container. a program has been interrupted. Check the drain hose. Empty container See To switch off the message: Open and close the door while the dryer is switched on or switch the dryer off and back on again. Blockage detected. lights up after a program has been interrupted.
Frequently Asked Questions Unsatisfactory drying results Problem Possible cause and solution The laundry is not sufficiently dry. The load consisted of different types of fabric. Finish drying using the Time Dry timed drying program. Select a more suitable program next time. Tip: You can alter the residual moisture level for some programs. See “Settings”. The laundry or featherfilled pillows develop a smell after drying. The laundry was washed with insufficient detergent.
Frequently Asked Questions The drying cycle duration is very long. Problem Possible cause and solution The drying process goes on too long or even switches off.* The room in which the tumble dryer is located is too warm. Ventilate the room thoroughly. Detergent residues, hair, and fine lint can clog the filters. Clean the lint filters and the plinth filter. Remove visible lint: . . . on the bottom left, behind the flap in the heat exchanger cavity (see “Cleaning and care”); . . .
Frequently Asked Questions General problems with the tumble dryer Problem Possible cause and solution You can hear operating noises (buzzing/ humming). This is not a fault. The compressor (heat pump) is operating. No action required. These noises are quite normal and can be heard when the compressor is operating. A program does not start. There is no obvious cause. Connect the power plug. Turn on the tumble dryer. Close the door. Check whether the fuse has tripped.
Frequently Asked Questions Bottom right grille In general, the cooling fins behind the grille on the bottom right do not need cleaning. They should only be cleaned if the drying process is taking an exceptionally long time due to a very high level of dust or lint in the room in which the dryer is located. First open the flap for the plinth filter (bottom left). Danger of injury! Do not touch the cooling fins with your hands. You could cut yourself.
Technical Service Contact in case of fault Warranty In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or Miele Technical Service. For further information, please refer to your warranty booklet. Contact information for Miele Technical Service can be found at the end of this document. Optional accessories Optional accessories for this tumble dryer are available from your Miele dealer or Miele Technical Service.
Installation instructions Alteration rights reserved. Visit our website for all the current product specifications, technical appliance information, and warranty information. To avoid accidents or damage to the appliance, please read these instructions before installing and/or using it.
IMPORTANT SAFETY INSTRUCTIONS , WARNING - Risk of Fire To reduce the risk of severe injury or death, follow all installation instructions. Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer's instructions and local codes. Repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and could void the warranty.
IMPORTANT SAFETY INSTRUCTIONS The installation of this unit in non stationary locations (e.g. ships) must be performed by a qualified installer or service agency, in strict accordance with national and local safety regulations and standards. Do not install the machine in rooms where temperatures below freezing may occur. If there is any doubt concerning installation, contact Miele’s Technical Service Department. USA 1-800-999-1360 techserv@mieleusa.com CDN 1-800-565-6435 service@miele.
Installation and connection Front view a Drain hose for condensed water b Power cord – Observe the section entitled “Electrical connection”.
Installation and connection Rear view a Protruding lid for holding when moving the tumble dryer (see arrows) b Drain hose for condensed water c Hook for winding the power cord during transport d Power cord Transporting the tumble dryer Only transport the tumble dryer as illustrated in order to avoid damaging it. If the tumble dryer is being transported on its side, it must be tipped onto its left or right side.
Installation and connection Installation Leveling the tumble dryer Ensure that no closeable door, sliding door, or an oppositely hinged door is installed that would hinder the door of the dryer being opened in any way. Downtime after installation After installation, downtime of 1 hour is required before connecting the tumble dryer to the electricity supply. Otherwise, the heat pump could be damaged. Ventilation The cool air intake at the front of the dryer must not be blocked or covered.
Installation and connection the condensed water container (which you will need to empty again) or out through the drain hose. Additional installation requirements All installations must be carried out in accordance with local regulations. Installing the dryer in a closet Minimum installation distance You must insert sufficiently large ventilation openings into the closet door. You can also open the closet door slightly while the dryer is operating.
Installation and connection Installing the dryer in a floor-to-ceiling closet You can also insert a ventilation opening at the top of the closet. In addition, you must also provide an opening on the bottom side of the closet door. Direct ventilation is also possible via an air conditioning outlet in the closet. The air must be able to circulate freely at the top of the closet. The air supply must not be hindered by a shelf.
Installation and connection Product dimensions Dimensions Washer-dryer stack – WTV502 or WTV512 5.2 ft (1.6 m) drain hose, detachable, top right on the rear 6.
Installation and connection Electrical connection GROUNDING INSTRUCTIONS The electrical safety of this dryer can only be guaranteed when continuity is complete between it and an effective grounding system. It is essential that this standard safety requirement is observed and regularly tested. If in any doubt, please have the electrical installation inspected by a qualified electrician. Miele cannot be held liable for the consequences of an inadequate grounding system.
Installation and connection External draining of condensed water Note When drying is in progress, condensed water is pumped into the condensed water container through the drain hose which is located at the back of the dryer. The condensed water can also be externally drained away via the drain hose on the back of the dryer. This means that the condensed water container no longer has to be emptied. Drain hose length: 5.2 ft (1.6 m) Maximum delivery head: 4.9 ft (1.
Installation and connection Changing the door hinging You can change the door hinging on this tumble dryer yourself. For safety reasons, the tumble dryer must be disconnected from the electricity supply before changing the door hinging. You will need: – a Torx T20 and T30 screwdriver – a flat head screwdriver or pointed pliers Hold the door securely and pull it forwards: to remove the door you will need to pull the base plate of the hinge with its 2 pins out of the dryer.
Installation and connection Turn the door lock by 180°. Press the door lock into the openings on the opposite side of the door opening. 3. Remove the lock catch from the door First take the rubber seal off the door and place this to one side. Adjust the position of the door lock so that the screw holes line up with those in the front panel of the dryer . Screw in both Torx screws in order to secure the door lock. Use a T20 Torx screwdriver to remove screw on the lock catch.
Installation and connection 4. Dismantle the door hinge from the door The door hinge cover must be unclipped from position and then removed. Remove the lock catch from the cover. This lock catch cover is no longer needed. Use a screwdriver to press down gently on position on the door hinge cover. Using a little force, pull out door hinge cover . This lock catch cover is no longer needed. Insert the lock catch into the new cover supplied with the dryer.
Installation and connection 5. Change the door hinge on the door The door hinge is secured to the door with 2 angled rods. These rods need to be removed with a screwdriver or pointed pliers. Tip: In some circumstances, the rods can be difficult to dislodge. Moving the screwdriver with a levering action while pulling at the same time may help to work the rods free. Remove the door hinge and turn it by 180°. Refit the door hinge on the opposite side of the door.
Installation and connection You now need the new door hinge cover supplied with the dryer. 6. Change the lock catch on the door You now need the new lock catch cover supplied with the dryer which you have already fitted with the lock catch. Fit new door hinge cover and clip it into position. Push the lock catch cover with its lock catch into position. Tighten the screw .
Installation and connection Refitting Now that you have changed the 7. Refit the door door hinging, the door will open from the opposite side. Press the rubber seal back into the groove on the door. Position the door in front of the dryer. Fit the base of the door hinge with its 2 pins into the openings on the dryer. The base of the door hinge must be flush with the front panel of the dryer. The door cannot fall off in this position.
Technical data Height 33 7/16" (850 mm) Width 23 7/16" (596 mm) Depth 25 5/16" (643 mm) Depth with door open 42 3/8" (1077 mm) Slot-in Yes Stackable Yes Weight Approx. 137 lbs (62 kg) Drum volume 31.7 gal (120 l) Load quantity 17.6 lb (8 kg) dry laundry Capacity of condensed water container 1.27 gal (4.8 l) Hose length 63" (1.60 m) Maximum head height 59" (1.
Settings Selecting settings Calling up settings Touch the or sensor button until the setting you want appears in the display. You can alter the tumble dryer's electronics to suit changing requirements with the settings. The settings can be altered at any time. – The sensor button scrolls down the list. Turn the program selector to More programs/. Time Dry OK The following appears in the display: OK Confirm with the OK sensor button.
Settings Language The display can be set to appear in one of several different languages. Keypad tone When this setting is activated, a signal tone will sound each time a sensor button is touched. The flag after the word Language acts as a guide to prevent a language which will not be understood from being set. Options The language selected is saved to memory.
Settings Airway indicator Lint should be removed after drying. In addition, this indicator will remind you to clean the filters when a certain amount of lint has collected in them: Clean plinth filter. See You can decide at what level of lint this reminder should be given. Options You will have an idea of how often this should be done after a few drying programs. – Off This reminder indicator does not appear.
Settings Code The PIN code prevents your dryer being used without your knowledge. Options – Activate The code is 250 and can be activated. When the PIN code has been activated, you have to enter a code after switching the dryer on. Otherwise the dryer cannot be operated. – Deactivate For using the dryer without entering the code. This only appears if the PIN code has been activated previously. – Change You can enter a code of your own. Important! Make a note of the new PIN code.
Settings Display switch-off To save energy the display and sensor buttons will go out after 10 minutes and the Start/Stop button will flash slowly. You can alter this setting. Options – On (default setting) The display will go out (after 10 minutes): The activation of the delay start, the buzzer, or the ECO feedback data are not saved. Anti-Crease After the drying cycle has finished, the drum will continue to rotate in a special Anti-crease rhythm.
Settings Miele@home Control the networking of your dryer with your WiFi network. The following points may appear in the submenu: Connection status (visible if Miele@home is activated) The following values are displayed: – The quality of WiFi reception – The network name Set up – The IP address This message only appears if the dryer has not yet been connected to a WiFi network. Set up again Please refer to “Initial commissioning” to set up the connection.
Settings Remote control SmartGrid The Remote control setting is only visible if the Miele@home setting is set up and activated. The Remote control setting is only visible if the Miele@home setting is set up and activated. Once the Miele@mobile app has been installed on your mobile device, you can check the status of your tumble dryer from anywhere and start it remotely. You can also control it remotely via the MobileControl program.
Please have the model and serial number of your appliance available when contacting Technical Service. U.S.A. Canada Miele, Inc. Importer Miele Limited National Headquarters 9 Independence Way Princeton, NJ 08540 Phone: 800-843-7231 609-419-4298 Fax: www.mieleusa.com Technical Service & Support Phone: 800-999-1360 888-586-8056 Fax: TechnicalService@mieleusa.com International Headquarters Miele & Cie.
TWF 160 WP en-US M.-Nr.