Operating and installation instructions Heat-pump dryer Always read the operating instructions before setting up, installing and commissioning the appliance. This prevents both personal injury and damage to the appliance. en-GB M.-Nr.
Contents Caring for the environment ................................................................................. 7 Warning and Safety instructions ......................................................................... 8 Operating the tumble dryer ................................................................................ Fascia panel .......................................................................................................... Sensors and touch display with sensors..................
Contents Programme overview .......................................................................................... Label...................................................................................................................... Programme packages ........................................................................................... Standard................................................................................................................ Sport................................
Contents Cleaning the bottom right grille/heat exchanger ................................................... Removing the grille........................................................................................... Cleaning the cooling fins .................................................................................. Replacing the grille........................................................................................... Cleaning the tumble dryer .............................................
Contents Supervisor level ................................................................................................... Accessing supervisor level .................................................................................... Access via code .................................................................................................... Change code ......................................................................................................... Closing the settings menu..............
Contents External applications ............................................................................................. 98 Peak load signal ............................................................................................... 98 Peak load prevention........................................................................................ 98 COM module selection..................................................................................... 98 WiFi...........................................
Caring for the environment Disposal of the packing material Disposing of your old appliance The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Electrical and electronic appliances often contain valuable materials. They also contain specific materials, compounds and components, which were essential for their correct function and safety.
Warning and Safety instructions It is essential to read these instructions. This tumble dryer complies with all current local and national safety requirements. However, inappropriate use can lead to personal injury and damage to property. Read the operating instructions carefully before using the tumble dryer. They contain important information on safety, installation, use and maintenance. This prevents both personal injury and damage to the tumble dryer.
Warning and Safety instructions This tumble dryer may also be operated in public areas. The tumble dryer is not intended for outdoor use. This appliance can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, if they are supervised whilst using it or have been shown how to use it in a safe way and understand and recognise the consequences of incorrect operation.
Warning and Safety instructions The appliance may only be operated when the following conditions are met: – The ship’s hull is longer than 24 metres. – The list of the vessel is not more than 2°. – Any external vibration is no more than 150 Hz at an amplitude of 0.35 mm. The safe operation and correct functioning of the appliance can only be guaranteed if the above conditions are met. The appliance may not be operated on an open deck.
Warning and Safety instructions Faulty components must only be replaced by genuine Miele original spare parts. The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used. To ensure the correct performance of the tumble dryer and to prevent the risk of faults and fire, it is important to carry out maintenance on a regular basis.
Warning and Safety instructions This tumble dryer is supplied with a special lamp to cope with particular conditions (e.g. relating to temperature, moisture, chemical resistance, abrasion resistance and vibration). This special lamp must only be used for the purpose for which it is intended. It is not suitable for room lighting. Replacement lamps may only be fitted by a Miele authorised person or by Miele Service.
Warning and Safety instructions – children climbing onto or into the dryer or hiding things in it. – pets or other small animals climbing into it. Do not use a pressure washer or hose to clean the tumble dryer. Always keep the area around the tumble dryer free of dust and fluff. Dust drawn into the dryer can, over time, cause blockages. Faults can then occur as well as the risk of fire. The tumble dryer must not be used – without the fluff filters in place or without the filter in the plinth.
Warning and Safety instructions To ensure problem-free operation: – After every cycle remove the fluff from the surfaces of the fluff filters. – Clean the airways (fluff filters, plinth filter, bottom right grille) as soon as the prompt to do so appears in the display. Do not install the tumble dryer in a room where there is a risk of frost occurring. At temperatures around freezing point the tumble dryer may not be able to operate properly.
Warning and Safety instructions To prevent the risk of fire, the following textiles must not be dried in this tumble dryer: – items which have not been washed. – Items, such as workwear, which have not been thoroughly cleaned and which are still soiled with grease, oil or other deposits (such as cosmetics, lotions etc). If items have not been thoroughly cleaned there is a danger that these might ignite when heated, even after they have been removed from the dryer at the end of the programme.
Warning and Safety instructions Fire hazard. This tumble dryer must not be connected to a controllable socket (e.g. a timer or a peak-load switch-off device). The tumble dryer may only be operated with a peak-load device if this is connected to the tumble dryer via the Miele XCI box and the relevant settings have been configured on the tumble dryer. There is a risk of the laundry igniting itself if the drying programme is cancelled before the cooling phase has finished.
Warning and Safety instructions Do not expose the dryer to air which is contaminated with vapour of chlorine, fluorine or other solvents. Danger of fire. For tumble dryers with stainless steel surfaces: The stainless steel surfaces must not come into contact with liquid cleaning and disinfecting agents which contain chlorine or sodium hypochlorite. These agents can have a corrosive effect on stainless steel. Aggressive vapours containing chlorine can also be corrosive.
Warning and Safety instructions There is the risk of fire or damage to the tumble dryer if the following instructions are not observed: – Never refill a flacon with fragrance. – Never use a faulty fragrance flacon. Dispose of an empty fragrance flacon with the household waste and never use it for any other purpose. Please also observe the information supplied with the fragrance flacon. Accessories Only use genuine Miele original spare parts and accessories with this appliance.
Operating the tumble dryer Fascia panel a Language sensor For selecting the current user language. The operating language is displayed again at the end of the programme. e Optical interface For service technicians. f Button For switching the tumble dryer on and off. The tumble dryer switches b Back sensor off automatically to save energy. This occurs 15 minutes after the end of For going back one level in the menu.
Operating the tumble dryer Sensors and touch display with sensors The sensors , and Start/Stop and the sensors in the display respond to finger tip contact. Every touch of a sensor is confirmed with an audible tone. You can adjust the volume of the keypad tone or switch it off (see information in “Supervisor level”). The control panel with sensors and the touch display can be scratched by pointed or sharp objects, e.g. pens. Only touch the display with your fingers.
Operating the tumble dryer Extras menu (multiple choice) Examples of how to operate the appliance Extras Option lists Gentle tumble Programme menu (single option list) Programmes Cottons 11:02 11:02 Express Shirts Anti-crease OK Minimum iron Delicates Denim Touch one or several Extras to select it/ them. Currently selected Extras are marked orange. Touch a programme name to select the drying programme. The display will change to the standard menu for that programme.
Operating the tumble dryer Status Tip: For some settings, depending on the value range and increments, the value can also be set using a numerical keypad. Briefly touching a number will bring up the numerical keypad. Once a valid number has been entered, the OK sensor will be highlighted green. Time left Cottons 11:02 2:27 h Drying Clock display 14 02 13 01 If an orange bar appears at the top of the screen in the middle of the display, you can open the pull-down menu.
Operating the tumble dryer Symbols on the display Operating a launderette machine Drying levels The entry menu will vary depending on the programming status (see “Controls” under “Supervisor level”). Shortcuts are the easiest way to operate the machine. Operating staff are unable to change pre-set programmes. Launderette ext.
Initial commissioning Switch on the tumble dryer Press the control. The welcome screen will light up. Risk of injury or damage to property due to improper installation. Incorrect installation of the tumble dryer can lead to personal injury or damage to property. Before commissioning the tumble dryer for the first time, make sure it has been installed and connected correctly. See “Installation”. Setting the language You will be asked to select the language you require for the display.
Initial commissioning Reference to external appliances Setting the date Date A reference to external hardware appears. 21 22 May June 2021 2020 Confirm with the OK sensor. 23 July 2019 24 25 August September 2018 Before initial commissioning, connect the XCI box or slide a communication module into the slot on the back of the tumble dryer. The tumble dryer must be disconnected from the mains before this is carried out. Then start the commissioning process.
Initial commissioning Confirm time request Selecting programme packages The following question appears in the display: You can select various programmes from the programme packages. Any programmes already active are marked in orange. Should the clock display not be shown? Touch the yes or no sensor. If you select yes, the system will skip the Clock display setting. Programme packages Label If you select no, the display will switch to the Clock display setting.
Initial commissioning Setting up a payment system If you wish to set up a payment system, read the “Payment system” section of the “Supervisor level” chapter. These settings can only be changed during the initial commissioning process. If you wish to change the settings after the commissioning process, please contact Miele Service. If you do not wish to set up a payment system, you can skip this stage.
1. Notes on correct laundry care Washing – Heavily soiled laundry must be washed particularly thoroughly. Use sufficient detergent and select a high temperature. If in doubt, wash the items several times. – New, coloured items must be washed thoroughly and separately. Do not dry these items with light coloured garments. There is the risk of colours running and discolouring other garments or even plastic components in the tumble dryer.
2. Load the tumble dryer Loading the laundry Preventing textile damage. Before loading, read chapter “1. Notes on correct laundry care.” Open the door. Load the laundry. Socket for the fragrance flacon The “Fragrance flacon” chapter describes how to use the fragrance flacon. If you are not using a fragrance flacon: push the tab down completely (see arrow) so that the socket is closed. Otherwise, fluff will accumulate here. Closing the door Preventing textile damage.
3. Selecting a programme Switch on the tumble dryer Alternatively, you can select a programme via: Favourites*. Press the control. * The preset programmes under vourites cannot be changed. The drum lighting will come on. The drum lighting will automatically go out after a few minutes and/or after the start of a programme to save energy. Selecting a programme 11:02 Programmes Favourites Supervisor Fa- Touch the Favourites sensor.
4. Selecting programme settings Selecting the duration (timed programmes) Main menu for a programme Select the drying level You can select the programme duration yourself.* With many programmes, you can change the preset drying level. Depending on the programme, you can select different drying levels. Overview * The time frame for the selected programme duration can be limited by Miele Service.
4. Selecting programme settings Anti-crease Selecting extra options The drying programmes can be augmented with various extra options. Overview 11:02 Weight Drying level 8,0 kg Normal The anti-crease function is switched off as the factory default setting. It can be switched on in the supervisor level with a variable duration of up to 12 hours. Cottons Extras 1:56h not selected OK Touch the Extras sensor.
5. Starting the programme Payment systems Tip: If your machine is connected to a payment system, the amount of payment required will appear in the display. Once the programme has started, do not open the door or cancel the programme. Depending on the settings, money may be lost in the payment system.
6. End of programme – unloading the drum End of programme Unloading the drum The laundry will be cooled down shortly before the end of the programme. The laundry can be unloaded. – Finish lights up If Anti-crease * was selected, the drum will rotate in intervals. This minimises creasing if the laundry cannot be removed from the machine immediately. * The anti-crease function is deactivated as standard. The tumble dryer will switch off automatically 15 minutes after the end of a programme.
Timer The Delay start must be activated in the Supervisor level so that the timer can be selected. Before the programme starts, the Timer can be used to select a programme start time or programme end time. Setting the timer Touch the Timer sensor. Select the option Finish at, Start in or Start at. The door will lock and the time until the programme starts will appear in the display. After the programme has started, the selected delay start period can only be changed by interrupting the programme.
Programme overview All weights marked with * are based on the weight of dry laundry. Label Cottons Eco maximum 8 kg* Items Cotton items such as those described under Cottons Normal with normal residual moisture. Note – Items are dried to a Normal level only in this programme. – The Cottons programme is the most energy-efficient for drying cotton items with normal residual moisture levels.
Programme overview Programme packages You can select various programmes from the programme packages. The programmes will appear in the programme list. Standard Cottons maximum 8 kg* Extra dry, Normal plus, Normal Items – Single and multi-layered cotton items. – Towelling, T-shirts, underwear, jersey bed linen, baby clothes. – Workwear, jackets, cotton blankets, aprons, tea towels, bed linen, towels, overalls, boil-proof table linen. Note – Select Extra dry for multi-layered and very thick fabrics.
Programme overview Express maximum 4 kg* Extra dry, Normal plus, Normal, Hand iron plus, Hand iron, Machine iron Items Garments suitable for the Cottons programme Note Shorter programme duration Delicates Max. load 4 kg* Normal plus, Normal, Hand iron plus Use for – Delicate synthetic, cotton or mixed fibre fabrics. – Lightweight pullovers, dresses, trousers, overalls, table cloths, shirts and blouses. – Lingerie and appliquéd fabrics. Note Less creasing occurs in this programme.
Programme overview Silks Max. load 1 kg* Use for Silk garments which are suitable for tumble drying, e.g. blouses and shirts Note – Programme for reduced creasing. – Items are not dried completely in this programme. – Remove the garments as soon as the programme has finished. Towelling Max. load 8 kg* Use for Large quantities of single-layered and multi-layered towelling items. These include, for example, towels, bath robes, face flannels, flannel bed linen.
Programme overview Timed drying – warm air Items maximum 8 kg* – Jackets, pillows, sleeping bags and other padded items. – Multi-layered textiles such as thick cotton tablecloths. – Individual items, e.g. bath towels, swimwear and tea-towels. Note – For finishing off multi-layered fabrics or padded garments that have dried unevenly. – For drying a few items or individual garments. – Do not select the longest drying time to start with. Check the items as you are drying them to find the optimum time.
Programme overview Sport Sportswear Max. load 3 kg* Use for Sportswear that is suitable for drying in a tumble dryer. Note Items are dried to a Normal level only in this programme. Outerwear Max. load 2.5 kg* Normal, Hand iron plus Use for Outerwear which is suitable for tumble drying. Proofing Max. load 2.5 kg* Textiles Microfibre fabrics, skiwear, outdoor wear, fine, close-weave cotton garments (poplin), and table linen which are suitable for drying in a tumble dryer.
Programme overview Soft furnishings Down bedding Max. load 2 kg* Use for Bedding suitable for tumble drying (duvets or pillows filled with down or feathers). Note Items are dried to a Normal level only in this programme. Tip Feathers have a tendency of developing a strong odour when they are warm. Allow bedding to air outside the tumble dryer after tumble drying. Synthetic bedding maximum 2 kg* Items Bedding suitable for drying in a tumble dryer (duvets or pillows with synthetic fillings).
Programme overview Hygiene In the hygiene programmes, items will be dried with a temperature that is constant over an extended period (longer temperature holding time). This kills off micro-organisms such as germs or dust mites and reduces allergens in the laundry. If a hygiene programme is cancelled early, micro-organisms will not be killed. Do not cancel this programme. Cottons hygiene Max. load 4 kg* Use for Cotton or linen items that come into direct contact with the skin.
Programme overview WetCare WetCare Sensitive Items Non-washable outerwear Note The garment is briefly dried and fluffed up WetCare Silks maximum 2.5 kg* maximum 2.5 kg* Normal, Hand iron plus, Hand iron Items Non-washable silk garments which crease easily WetCare Intensive maximum 2.
Programme overview Special programmes (3) You can put together five special programmes and assign your own programme names. Enter these into the tables. Load: maximum 8 kg (weight of dry items) – – – – – – Example – [Special programme 1] Dry+ (4) Res.
Changing the programme sequence Payment systems Opening the door or cancelling the programme after it has started may cause a loss of credit (depending on how the tumble dryer was set up*). * Either during the commissioning process or subsequently, a Miele service technician can reset the payment system so that programming changes can be made. Changing a programme once it has started You cannot change to another programme once a programme has started (this prevents unintentional alterations).
Fragrance flacon Inserting a fragrance flacon Fragrance flacons (optional accessories) can be used to give your laundry a pleasant scent. Risk of fire and damage to the health if fragrance flacons are used incorrectly. The leaked fragrance can damage your health if it comes into contact with your body. Leaked fragrance can cause fire.
Fragrance flacon Insert the fragrance flacon as far it will go into the socket. Turn the outer ring clockwise a little. The fragrance flacon may slip out. Turn the outer ring in such a way that the markers and line up. The markers and must line up with one another.
Fragrance flacon Opening the fragrance flacon Closing the fragrance flacon Before drying, you can select the intensity of the fragrance. After drying, the fragrance flacon should be closed to prevent the fragrance from escaping needlessly. Turn the outer ring clockwise: the further you open the fragrance flacon, the more intense the fragrance. Damp laundry and longer drying durations with sufficient heat transfer are needed for the fragrance to be released into the laundry effectively.
Fragrance flacon Removing/replacing the fragrance flacon Turn the outer ring anti-clockwise until the markers a and b line up. Replace the fragrance flacon with a new one. When not in use, you can store the fragrance flacon in its original packaging. Fragrance flacons are available to order from Miele or online. 50 The fragrance can leak out of the flacon. Do not lay the fragrance flacon down.
Cleaning and care Observe the cleaning intervals This tumble dryer is equipped with a multi-stage filter system, which consists of a fluff filter (1.) and a filter in the plinth (2.). This filter system collects all fluff generated during the drying process. 1. Cleaning intervals for fluff filters The fluff filters are located in the filling area of the dryer drum. Failure to clean the filter regularly could increase drying times. Fire hazard due to irregular maintenance.
Cleaning and care 2. Cleaning intervals for the plinth filter The filter (in the plinth) is located behind the fluff filter flap on the bottom left. With normal use Clean when Clean airways appears in the display. With continuous use Clean once daily and additionally when the prompt appears in the display. The surface of the filter in the filter insert is visible after removing the fluff filter. This filter surface must also be cleaned. To clear the message: Touch the OK sensor.
Cleaning and care 3. Cleaning interval for grille on bottom right/heat exchanger for dissipating heat Clean when Open bottom right grille, clean the heat exchanger appears in the display. The grille on the bottom right can be removed. The heat exchanger for dissipating heat is behind the grille. Keep the room where the tumble dryer is located free from dust and fluff. This will reduce the requirement to clean. See “Bottom right grille/heat exchanger”.
Cleaning and care Cleaning the fluff filters This tumble dryer has 2 fluff filters in the loading area. The upper and lower fluff filters trap fluff produced during the drying process. Removing the fragrance flacon The intensity of the fragrance will be diminished if the fluff filters and the plinth filter are not cleaned. Remove the fragrance flacon as described in “Removing/replacing the fragrance flacon” under “Fragrance flacons”. Remove the fluff (see arrows).
Cleaning and care Cleaning the fluff filters and air flow openings thoroughly If the drying duration has become longer or the surface of the filters is visibly compacted with fluff, you should carry out the following cleaning procedure. Cleaning the fluff filters while dry Pull the upper fluff filter forwards to remove it. Use a vacuum cleaner with a long crevice nozzle attached to remove any visible fluff from the upper air flow openings.
Cleaning and care Push the lower fluff filter in completely and lock it with the yellow dial. Push the upper fluff filter all the way in. Close the door.
Cleaning and care Filter in the plinth The fluff filter in the plinth collects finer fluff, hair and detergent residues that have got through the surfaces of the fluff filters. Removing the fluff filter Pull the fluff filter out at an angle. Reach behind the catch with your finger. Open the fluff filter flap. Pull the handle out of the fluff filter. Use the handle to pull out the fluff filter at an angle forwards and to the right.
Cleaning and care Cleaning the fluff filter with water Clean the filter thoroughly under running water. Squeeze the filter very carefully several times as you rinse it. Rinse the filter until all visible residues have been removed. Damage caused by a insufficiently cleaned or damaged fluff filter. If the filter has not been properly cleaned or is damaged, the heat exchanger will be clogged. There will be an insufficient flow of air and heat in the heat exchanger.
Cleaning and care Deformation Deformations indicate that the filter has become blocked and worn by continuous use. Cracks, tears, indentations White residues or residues of other colours Residues arise from laundry fibres and traces of detergent components which can clog the filter. They can be found on the front and side edges of the filter. In extreme cases, they can form stubborn crust.
Cleaning and care Cleaning the filter insert (in the plinth) The surface of the filter in the filter insert is visible after removing the fluff filter in the plinth. This filter surface must only be cleaned if there is a visible accumulation of fluff. Removing the filter insert If the filter insert is clogged up and soiled, it must be removed and cleaned under running water. Use the handle to pull out the filter insert at an angle forwards and to the right.
Cleaning and care Check the cooling fins on the heat exchanger Danger of injury if you touch the cooling fins. You could cut yourself. Do not touch the cooling fins with your hands. After removing the filter insert, visually check the cooling fins on the heat exchanger. Check for any accumulation of fluff. If you notice any visible soiling, carefully vacuum it up with a vacuum cleaner. Use a dusting brush or the narrow crevice nozzle. Risk of damage if cooling fins are cleaned incorrectly.
Cleaning and care Refitting the filter insert (in the plinth) Use the handle to slide the filter insert to the right at an angle behind the edge. Then press on the handle until the filter is secured in position on the left. 62 Press the frame of the filter insert in at the positions marked PUSH until it audibly engages. Refitting the fluff filter in the plinth Fit the fluff filter back on the handle. Make sure it is the correct way round.
Cleaning and care Cleaning and closing the fluff filter flap Use the handle to slide the fluff filter on the right at an angle behind the edge. Use a damp cloth to remove any fluff. Make sure that you do not damage the rubber seal when doing this. Then press on the handle until the fluff filter is secured in position. Close the fluff filter flap.
Cleaning and care Cleaning the bottom right grille/heat exchanger The heat exchanger's cooling fins behind the grille can become blocked with dust and dirt drawn in from the surrounding area. Removing the grille Open the fluff filter flap. Open the bottom right grille, e.g. using a spoon handle. Insert a spoon handle underneath the grille (under the recess ). Press and lever the grille gently until it opens on the left-hand side .
Cleaning and care Cleaning the cooling fins Replacing the grille Check whether the cooling fins are clogged. Danger of injury caused by touching the cooling fins. You could cut yourself. Do not touch the cooling fins with your hands. If there is visible soiling: Insert the grille on the right-hand side. Press the grille firmly on the left-hand side. Carefully vacuum up any visible fluff or soiling. Use a dusting brush or the narrow crevice nozzle.
Cleaning and care Cleaning the tumble dryer Disconnect the tumble dryer from the electrical supply. Damage caused by the use of unsuitable care products. Unsuitable care products could damage plastic surfaces and other parts. Do not use any solvents, abrasive cleaners, glass cleaners, or all-purpose cleaners. Danger of electric shock caused by water. There is a risk of electric shock if water runs over or into the tumble dryer. Never spray the tumble dryer with water.
Problem solving guide Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it. The display indicates the following messages or faults Message Cause and remedy This is not an error. In some programmes, if the drum has been underloaded or is empty, the programme will be cancelled.
Problem solving guide Message Cause and remedy lights The dryer is not operating in the most effective or efup at the end of a ficient way. Possible causes may be blockages caused by fluff or detergent residues. programme. Generally, cleaning the fluff filter will be enough to solve the problem. Also check the plinth filter and clean it if necessary. When you remove the plinth filter, also check the filter insert behind it. Clean if necessary.
Problem solving guide Message Cause and remedy The plinth filter looks clean after thorough cleaning. However, the programme terminates and the error message appears again. It is likely that there is still underlying residue that could not be removed. To delete the message: Touch the OK sensor control. Replace the plinth filter with a new one. You can reactivate the removed, “old” plinth filter in the washing machine.
Problem solving guide Unsatisfactory drying results Problem Cause and remedy The laundry is not suffi- The load consisted of different types of fabric. ciently dry. Finish drying using the Timed drying warm air programme. Large items of laundry have rolled up, causing a problem. The individual items of laundry are still damp. The laundry could not be disentangled in the programme you selected. Smaller items have rolled up into one. Disentangle the laundry. Select the Large items programme.
Problem solving guide The drying cycle duration is very long Problem Cause and remedy The drying process goes on too long or even switches off*. The room where the tumble dryer is located is too warm. Ventilate the room thoroughly. Detergent residues, hair and fine fluff can clog the filters. Clean the fluff filters and the filter in the plinth. See “Cleaning and care” for an in-depth description. If you have removed the plinth filter, also check the filter insert behind it. Clean it if necessary.
Problem solving guide General problems with the tumble dryer Problem Cause and remedy There are humming noises. The compressor is operating. These noises are quite normal and do not indicate a fault. The drum lighting does not come on. The drum lighting switches off automatically when the door is closed. To save energy, the drum lighting will switch off after a few minutes if the door is left open for an extended period.
Problem solving guide Reactivating the plinth filter You can reactivate one or more dirty plinth filters in the washing machine. You will then be able to use the plinth filter again for a reasonable period of time. Wash the plinth filter(s) separately, not with any laundry items. Do not add any detergent. Tip: Select a short wash programme with a maximum temperature of 40 °C and a maximum spin speed of 600 rpm. Select the Separate rinse programme, for example.
Service Contact in case of malfunction Optional accessories In the event of any faults which you cannot remedy yourself, please contact your Miele dealer or the Miele Customer Service Department. Optional accessories for this tumble dryer are available from your Miele Dealer or from the Miele Spare Parts Department. You can book a Miele Customer Service Department call-out online at www.miele.com/service.
*INSTALLATION* Installation Front view a Mains connection cable b Control panel c Door f Bottom right grille = Air cooling opening – Open only when a prompt appears in the display g Drain hose for condensation d Fluff filter flap for the filter in the plinth h Non-return valve, required – Open only when a prompt appears i Non-return valve, recommended in the display e 4 height-adjustable screw feet 75
*INSTALLATION* Installation Rear view a Interface for communicating with ex- d Module slot (for external communicaternal devices tion module) b Mains connection cable c Recesses under the protruding lid for transporting the appliance 76 e Drain hose for condensation
*INSTALLATION* Installation View from above Locations All measurements in mm Side view 777 737 850 1191 1100 Washer-dryer stack min. 300 Steel plinth 1702 Steel plinth* (open or closed bases) A stacking kit* is needed. This must be fitted by a Miele authorised service technician.
*INSTALLATION* Installation Transporting the tumble dryer to its installation site Damage caused by incorrect transportation of the tumble dryer. If the tumble dryer tips over, there is a danger of injury to people and damage to property. Ensure that the tumble dryer is stable during transportation. Transporting the tumble dryer If the tumble dryer is being transported on its side, it must be tipped onto its left or right side.
*INSTALLATION* Installation Installation Levelling the tumble dryer Ensure that no closeable door, sliding door, or an oppositely hinged door is installed that would hinder the door of the tumble dryer being opened in any way. Installing the tumble dryer on boats On other types of floor structures (in cases where the tumble dryer is installed on sea-going vessels, for example), the fixing materials must be provided on site.
*INSTALLATION* Installation Room ventilation External control equipment – Air drawn in for use in the drying process will be warm when it is expelled back into the room. It is therefore very important to ensure the room is adequately ventilated, particularly if the dryer is located in a small room. The XCI box accessory is needed to connect external control equipment, such as payment systems or peak load control units. – Make sure the room temperature is not too high.
*INSTALLATION* Installation Hose for external drainage of condensed water The condensed water is pumped away through the drain hose which is located at the back of the dryer. Laying the drain hose Damage to the drain hose due to incorrect handling. The drain hose can suffer damage and leak. Do not pull on the drain hose and do not stretch it or allow it to become kinked. Tip: Use the bow-shaped guide to prevent the drain hose from becoming kinked.
*INSTALLATION* Installation Example: Connected directly to a sink drain outlet Install adapter 1 to the sink drain outlet using nut 2. The nut is usually fitted with a washer which must be removed. Attach the end of the hose 4 to adapter 1. Use a screwdriver to tighten hose clip 3 up close to the nut. Insert the non-return valve 5 into the tumble dryer's drain hose 6. Install the non-return valve 5 so that the arrow points in the direction of flow (towards the sink). 1. Adapter 2. Nut 3.
*INSTALLATION* Installation Electrical connection This description applies to tumble dryers both with and without a mains plug. The following applies to tumble dryers with a mains plug: – This tumble dryer is supplied with a mains cable and plug ready for connection. – The electrical socket must be easily accessible so that the tumble dryer can be disconnected from the electricity supply. Damage caused by incorrect supply voltage.
Technical data Height 850 mm Width 596 mm Width (only for machines with a stainless steel lid) 605 mm Depth 777 mm Depth with door open 1191 mm Weight 75 kg Drum volume 130 l Load size 8 kg (weight of dry laundry) Hose length 1400 mm Length of connection cable 2000 mm Supply voltage See data plate on back of machine Rated load See data plate on back of machine Fuse rating See data plate on back of machine Test certifications awarded See data plate on back of machine LEDs Class 1
Technical data Conformity declaration Miele hereby declares that this heat-pump tumble dryer complies with Directive 2014/53/EU. The complete text of the EU declaration of conformity is available from one of the following internet addresses: – Products, Download from www.miele.co.uk – For service, information, operating instructions etc: go to www.miele.co.uk/domestic/customer-information-385.
Supervisor level Accessing supervisor level Closing the settings menu 11:02 Programmes Favourites Supervisor Touch the sensor. The display will then go back to the previous menu level. Touch the sensor. The display will change to the main menu. Help Touching the sensor takes you to the Supervisor level. Access via code Supervisor level is accessed using a code. Controls / Display Language The display can be set to appear in one of several different languages.
Supervisor level Language entry The display can be set to one of several different user languages. This setting allows you to determine how languages can be selected. The language can be changed as follows: International Six languages are available. The sensor is not active. Note the setting Set languages. Language setting The sensor can be used to select a language. All languages are available (factory default). You can change the order of the first four languages.
Supervisor level Clock display After selecting the clock format, you can set the time of day. Volume The volume for various sounds can be changed. Clock format The volume can be changed. – Factory default: 24-hour display – Finish tone – 12-hour display – Keypad tone – No clock – Welcome tone Set – Fault alarm The audible signal that indicates an error can be switched off. The volume cannot be changed here. – The time of day can be set. Date The date can be set after selecting the date format.
Supervisor level "Display" off status The display switches off to save energy; only the Start/Stop sensor flashes slowly. You can change this setting. Changing this setting leads to increased energy consumption. – Off No switching off "Machine" off status In order to save energy, the tumble dryer will switch off automatically after the end of the programme or if no further selection is made. You can change this setting. Changing this setting leads to increased energy consumption.
Supervisor level Memory The tumble dryer saves the settings that were last selected for a drying programme (drying stage and/or extra option, or the duration for some programmes). – Factory default: Off – On Temperature unit You can select the unit for the temperature display. – Factory default: °C – °F Weight unit You can decide whether load quantities are displayed in “kg” or “lbs”.
Supervisor level Programme selection Opening the Supervisor level (launderette version) Controls Switch the tumble dryer on and open the dryer door. You can select whether the tumble dryer is operated as a “launderette” machine. Shortcuts are the easiest way to operate the machine. Operating staff are unable to change pre-set programmes. Tip: Start by configuring all necessary settings and changes to the tumble dryer before adjusting any of the options below.
Supervisor level – Standard Factory default: All (selected) programmes are available. Four programmes are available. Four timed programmes* with different temperature levels are time-controlled via the tumble dryer electronics. The maximum laundry weight is 8 kg. Under Favourite programmes, you can set which four programmes to select/modify. The set value indicates the maximum running time and can be modified by the user. – Launderette, basic (4 prog) – Launderette ext.
Supervisor level Favourite programmes After switching on, you can also select a programme via: Favourites. 12 programmes can be stored as favourites based on your own priorities and requirements. These favourites will also be made available in the control options – Launderette ext. (12 prog) – Launderette, basic (4 prog) (the first four of the 12 favourites). The control options can be defined under Control. Tip: You can assign a different colour to each programme. In this case, the Prog.
Supervisor level Res. moisture programme – Final residual moisture: - 6 % (dry) – 40 % (damp) – Cooling down temp.
Supervisor level Sort programmes Programmes can be moved within the programme list and in the Favourites list. – Factory default: Off – On Moving programmes/favourites You can move/change the order of the programmes (programme menu – single option list). You can also move and change the order of the favourites that you edit in the Supervisor level under Favourite programmes. Touch the programme that you wish to move. Press and hold the sensor until the frame changes.
Supervisor level Process technology Anti-crease At the end of the programme, the drum will continue to rotate at intervals if the laundry is not removed immediately. Changing this setting leads to increased energy consumption. The setting can be switched off or a time between 1 and 12 hours can be selected. Factory default: Off Drying levels Changing this setting leads to increased energy consumption. You can alter the drying levels for the Cottons, Minimum iron and Automatic plus programmes.
Supervisor level Service Clean the airways The tumble dryer's electronics calculate the degree at which fluff or detergent residue in the fluff filters and air ducts are impairing performance. A message to check the contamination appears. You can decide at what level of fluff this reminder should be emitted. This prompt, which you can configure, is displayed: Clean airways Your message is displayed at the end of the programme and can be acknowledged with OK.
Supervisor level External applications Peak load signal External hardware is connected via the Miele XCI box. The peak-load negotiation function enables the tumble dryer to be connected to an energy management system. When a signal is registered, the tumble dryer's heater is switched off for a short period or the appliance is prevented from being switched on. The tumble dryer may only be operated with a peak-load system if this system is connected to the tumble dryer via the Miele XCI box.
Supervisor level – Reset (visible if already set up) Remote The network is no longer set up. A new connection has to be established in order to use the network again. Factory default: Off – The WiFi is switched off Remote Update – The WiFi connection will be reset to the factory default setting The RemoteUpdate function is used for updating the software in your tumble dryer. Network time The date and time can be synchronised over the network.
Supervisor level Running a RemoteUpdate If a RemoteUpdate is available for your washing machine, it will be displayed automatically when the Operator level is open. You can choose to start the RemoteUpdate immediately or wait until later. If you select “Start later”, the prompt to run the RemoteUpdate will be displayed again the next time you switch on your washing machine. The RemoteUpdate can take a few minutes.
Supervisor level Machine parameters Legal information Open source licences You can view information here. Copyrights and Licences Miele uses their own and third party software which is not subject to any socalled Open Source Licence for the operation and control of the appliance. This software/these software components are protected by copyright. The copyright powers of Miele and third parties have to be respected.
Supervisor level Time / impulse To be able to operate the tumble dryer with conventional payment systems where multiple coins can be inserted, you can adjust how much time is purchased each time a coin is inserted. A time of between 5 and 60 minutes can be set in increments. Factory default: 30 minutes F-back signal to pay system Setting the feedback signal for the coin box. – Factory default: Off – End of programme The feedback signal is sent at the end of the programme.
Supervisor level Debounce time In coin mode, the debounce time for the minimum payment signal that must be applied can be adjusted. – Factory setting: Short For coin boxes where the falling coin generates the paid pulse. – Long For central control units on a 230 V basis. Pay system override time Setting the transition signal for the coin box. Security time margin to prevent the coin box being tampered with.
International Service Contacts America: +1 866 694 5849 Australia, Asia, Oceania: +61 3 9764 7880 Europe, Africa, Middle East: +49 5241 89 66 877 E-mail: service@miele-marine.com www.miele.com/marine-service Manufacturer: Miele & Cie.
PDR 908 HP Marine en-GB M.-Nr.