Operating and Installation Instructions Heat-Pump Dryer Always read the operating instructions before setting up, installing, and commissioning the appliance. This prevents both personal injury and damage to the appliance. en-US M.-Nr.
Contents Caring for the environment ............................................................................. 7 IMPORTANT SAFETY INSTRUCTIONS ............................................................ 8 Operating the tumble dryer .............................................................................. Control panel ....................................................................................................... Sensor controls and touch display with sensor controls ....................
Contents Timer................................................................................................................... 33 Program chart.................................................................................................... Label.................................................................................................................... Program packages .............................................................................................. Standard.......................
Contents Cleaning the bottom-right grille/heat exchanger................................................. Removing the grille......................................................................................... Cleaning the cooling fins ................................................................................ Replacing the grille......................................................................................... Cleaning the tumble dryer ......................................................
Contents Demo program .................................................................................................... Closing the settings menu................................................................................... Controls / Display ................................................................................................ Language........................................................................................................ Language entry ....................................
Contents External applications ........................................................................................... Peak load signal ............................................................................................. Peak load prevention...................................................................................... Select KOM module ....................................................................................... Availability of Miele digital products ..........................
Caring for the environment Disposal of the packing material The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of your old appliance Electrical and electronic appliances contain valuable materials.
IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: It is essential to read all instructions before using the appliance. Do not allow children to play on or in the appliance. Close supervision is necessary when the appliance is used near children. Always close the door after use to prevent child hazards.
IMPORTANT SAFETY INSTRUCTIONS Important information regarding use of fabric softener sheets: We do not recommend use of fabric softener sheets. Use of fabric softener sheets can clog the surfaces of the lint filters, extending the drying time and increasing energy consumption. During subsequent cleaning, the plastic and surfaces of the lint filters can be damaged! The best results are obtained by using liquid fabric softener in the washing machine. Follow the manufacturer's instructions.
IMPORTANT SAFETY INSTRUCTIONS To prevent the risk of fire, the following textiles must not be dried in this dryer: - items which have not been washed. - items, such as work-wear, exposed to grease, oils, or other deposits (such as lotions or cosmetics) in your dryer. If these items have not been thoroughly cleaned there is a danger that they may contribute to a chemical reaction that could cause the laundry to ignite when heated even after being removed from the dryer.
IMPORTANT SAFETY INSTRUCTIONS Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire. To reduce the risk of fire due to contaminated loads, the final part of a tumble dryer cycle occurs without heat (cool down period). Avoid stopping a tumble dryer before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.
IMPORTANT SAFETY INSTRUCTIONS Do not modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician. Before installation, disconnect the tumble dryer from the electrical supply by shutting off the power main, unplugging the power cord or tripping the circuit breaker. Do not restore power until the installation is complete. Miele Tumble Dryers and Miele Washing Machines can be installed as a washer-dryer stack.
IMPORTANT SAFETY INSTRUCTIONS This tumble dryer is supplied with a special lamp to cope with particular conditions (e.g., temperature, moisture, chemical resistance, abrasion resistance, and vibration). This special lamp must only be used for the purpose for which it is intended. It is not suitable for room lighting. Replacement lamps should only be fitted by a Miele authorized person or by Miele Service.
IMPORTANT SAFETY INSTRUCTIONS Using a fragrance capsule (optional accessory) Only use genuine Miele original fragrance capsules. Store the fragrance capsule in its original packaging. Make sure that you always keep the fragrance flacon or the lint filter with the flacon inserted in it in a horizontal position when carrying, and do not tip or place it down on any surface. The fragrance can leak out of the flacon.
IMPORTANT SAFETY INSTRUCTIONS FCC Declaration of Conformity This appliance complies with Part 15 of the FCC regulations. This appliance has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and is subject to the following conditions: This appliance does not cause harmful interference. The appliances may be interconnected as desired.
Operating the tumble dryer Control panel a Language sensor control For selecting the current user language. The operating language is displayed again at the end of the program. b Back sensor control Takes you back one level in a menu. c Touch display d Sensor control Start/Stop For starting the selected drying program and canceling a program once it has started. The program selected can be started as soon as the sensor control starts flashing. 16 e Optical interface For Technical Service.
Operating the tumble dryer Sensor controls and touch display with sensor controls Programs The , , and Start/Stop sensor controls and the sensor controls in the display react to finger-tip contact. Every touch of a sensor control is confirmed with an audible keypad tone. You can adjust the volume of the keypad tone or switch it off (see “Supervisor level”). Favorites The control panel with sensor controls and the touch display can be scratched by pointed or sharp objects, e.g., pens.
Operating the tumble dryer Options menu (multiple selection) Examples of how to operate the appliance Extras Option lists Gentle tumble Program menu (single-option list) Programs Cottons 11:02 11:02 Express Shirts Anti-crease OK Minimum iron Delicates Denim Touch one or several Options to select it/them. Currently selected Options are highlighted in orange. Touch a program name to select the drying program. The display will change to the standard menu for that program.
Operating the tumble dryer Clock display 14 02 13 01 Pull-down menu The pull-down menu can be used to display information, e.g., about a drying program. Status Tip: For some settings, depending on the value range and increments, the value can also be set using a numerical keypad. Briefly touching the numbers will bring up the numerical keypad. Once a valid number has been entered, the OK sensor control will be highlighted in green.
Operating the tumble dryer Laundromat Logo Operating a laundromat machine The entry menu will vary depending on the programming status (see “Controls” under “Supervisor level”). Shortcuts are the easiest way to operate the machine. Operating staff are unable to change pre-set programs. Laundromat, basic 11:02 Cottons Cottons Delicates Cottons 11:02 Cottons Cottons Cottons Help The first 3 programs can be selected directly.
Operating the tumble dryer Laundromat Logo int. time / Laundromat Logo ext. time 11:02 Help 4 time programs with different temperature levels are available for selection. - Temperature level cold - Temperature level low - Temperature level medium - Temperature level high Laundromat Logo ext. time: the tumble dryer only functions correctly when it is provided with external time information by an external unit.
Initial commissioning Switching on the tumble dryer Press the button. The welcome screen will light up. Risk of injury or damage to property due to improper installation. Incorrect installation of the tumble dryer can lead to personal injury or damage to property. Before commissioning the tumble dryer for the first time, make sure it has been installed and connected correctly. See “Installation and connection”. Damage caused by switching the appliance on too soon.
Initial commissioning Reference to external appliances Setting the date Date A reference to external hardware appears. 21 22 May June 2023 2022 Confirm with the OK sensor control. 23 July 2021 24 25 August September 2020 2019 Connect the XCI box or XCI-AD accessory unit before using the appliance for the first time. Alternatively, slide a communication module into the slot on the back of the tumble dryer. The tumble dryer must be disconnected from the power supply for this process.
Initial commissioning Confirming the time request Selecting program packages The following question appears in the display: You can select various programs from the program packages. Any programs already active are highlighted in orange. Remove the clock display? Touch the Yes or No sensor control. Program packages If you select Yes, the system will skip the Clock display setting.
Initial commissioning Setting up a payment system Confirm with OK. If you wish to set up a payment system, read the “Payment system” section of the “Supervisor level” chapter. These settings can only be changed during the initial commissioning process. If you wish to change the settings after the commissioning process, please contact Miele Technical Service. In the main menu, touch the Programs sensor control. If you do not wish to set up a payment system, you can skip this stage.
1. Notes on correct laundry care Washing - Heavily soiled laundry must be washed particularly thoroughly. Use sufficient detergent and select a high temperature. If in doubt, wash the items several times. - New, colored items must be washed thoroughly and separately. Do not dry these items with light-colored garments. There is the risk of colors running and discoloring other garments or even plastic components in the tumble dryer. Dark-colored fibers can also settle on light-colored garments and vice versa.
2. Loading the tumble dryer Loading the laundry Textiles may be damaged. Before loading, read “1. Notes on correct laundry care”. Checking the socket for the fragrance flacon If you are not using a fragrance flacon, check that the socket is closed. The “Fragrance flacon” chapter describes how to use the fragrance flacon. Open the door. Load the laundry. Textiles may be damaged. When closing the door, make sure that laundry does not get trapped in the door opening.
3. Selecting a program Switching on the tumble dryer Press the button. * The pre-set programs under Favorites cannot be changed. The drum lighting will come on. The drum lighting will automatically go out after a few minutes and/or after the start of a program to save energy. Selecting a program 11:02 Programs Favorites Alternatively, you can select a program via: Favorites*. Touch the Favorites sensor control. The programs will appear in the display.
4. Selecting program settings Selecting the duration (timed programs) Main menu for a program Selecting the drying level The pre-set drying level for many programs can be changed if required. Different drying levels are available depending on the program. Overview 11:02 Weight Drying level 8,0 kg Normal You can select the program duration yourself.* * The time frame for the selected program duration can be limited by Technical Service.
4. Selecting program settings Gentle Selecting extra options The drying programs can be augmented with various extra options. Overview 11:02 Weight Drying level 8,0 kg Normal Extras not selected OK Touch the Extras sensor control. Extras 11:02 Gentle tumble Anti-crease OK Touch the sensor control for the option you want. Only press OK when the option appears on the display. The relevant symbol for the selected option or lights up.
5. Starting a program Payment system Tip: If your machine is connected to a payment system, the amount of payment required will appear in the display. Once the program has started, do not open the door or cancel the program. Depending on the settings, money may be lost in the payment system. Starting a program Program duration/Estimated time remaining The program duration depends on the quantity of laundry, the type of fabric, and the residual moisture in the laundry or also the water hardness.
6. End of program – removing the laundry End of program Removing the laundry The laundry will be cooled down shortly before the end of the program. The laundry can now be unloaded. - Finish lights up If Anti-crease * has been selected, the drum rotates in intervals. This reduces creasing if the laundry cannot be removed straight away. * The anti-crease function is switched off as the factory default setting. The tumble dryer will switch off automatically 15 minutes after the end of a program.
Timer The Delay start must be activated in the Supervisor level so that the timer can be selected. Before the program starts, the Timer can be used to select a program start time or program end time. Deleting the timer The selected delay-start period can be canceled before the program starts. Touch the , , or sensor control. Setting the timer The selected delay-start period will appear in the display. Touch the Timer sensor control. Touch the Delete sensor control.
Program chart All weights marked with * are based on the weight of dry laundry. Label Cottons Eco Maximum 17.6 lb (8 kg)* Items Cotton items such as those described under Cottons, Normal with normal residual moisture. Note - Items are dried to a Normal level only in this program. - The Cottons program is the most energy-efficient for drying cotton items with normal residual-moisture levels.
Program chart Program packages You can select various programs from the program packages. The programs will appear in the program list. Standard Cottons Maximum 17.6 lb (8 kg)* Extra Dry, Normal Plus, Normal Items - Single and multi-layered cotton items. - Towels, bathrobes, T-shirts, underwear, jersey bed linen, baby clothes. - Workwear, jackets, cotton blankets, overalls, dish towels, bed linen, towels, boil-proof table linens/drapes. Note - Select Extra Dry for multi-layered and very thick fabrics.
Program chart Express Maximum 8.8 lb (4 kg)* Extra Dry, Normal Plus, Normal, Hand iron plus, Hand iron, Machine iron Items Garments suitable for the Cottons program Note Shorter program duration Delicates Maximum 8.8 lb (4 kg)* Normal Plus, Normal, Hand iron plus Items - Delicate synthetic, cotton ,or mixed-fiber fabrics. - Lightweight pullovers, dresses, pants, overalls, table cloths, dress shirts, and blouses. - Lingerie and appliquéd fabrics. Note Less creasing occurs in this program.
Program chart Silks Maximum 2.2 lb (1 kg)* Items Silk garments which are suitable for tumble drying, e.g., blouses and shirts Note - Program for reduced creasing. - Items are not dried completely in this program. - Remove the garments as soon as the program has finished. Toweling Maximum 15.4 lb (7 kg)* Items Large quantities of single-layered and multi-layered toweling items. These include, for example, towels, bath towels, bath robes, face flannels, flannel bed linen.
Program chart Timed drying warm air Items Maximum 17.6 lb (8 kg)* - Voluminous items such as jackets, pillows, sleeping bags, and padded items. - Fabrics made up of multiple layers, e.g., heavy cotton table cloths. - Individual items of laundry, e.g., towels, swimwear, dish towels. Note - For airing multi-layered fabrics or large items that dry unevenly due to their make-up. - For drying a small number of individual garments. - Do not select the longest drying time to start with.
Program chart Sport Sportswear Maximum 6.6 lb (3 kg)* Items Sportswear that is suitable for drying in a tumble dryer. Note Items are dried to a Normal level only in this program. Outdoor Maximum 5.5 lb (2.5 kg)* Normal, Hand iron plus Items Outdoor clothing which is suitable for drying in a tumble dryer. Proofing Maximum 5.5 lb (2.
Program chart Soft furnishings Down Bedding Maximum 4.4 lb (2 kg)* Items Bedding suitable for tumble drying (duvets or pillows filled with down or feathers). Note Items are dried to a Normal level only in this program. Tip Feathers have a tendency of developing a strong odor when they are warm. Allow bedding to air outside the tumble dryer after drying. Synthetic Bedding Maximum 4.4 lb (2 kg)* Items Bedding suitable for tumble drying (duvets or pillows with a synthetic filling).
Program chart Hygiene In the hygiene programs, items will be dried with a temperature that is constant over an extended period (longer temperature-holding time). This kills off microorganisms such as germs or dust mites and reduces allergens in the laundry. If a hygiene program is canceled early, micro-organisms will not be killed. Do not cancel this program. Cottons hygiene Maximum 8.8 lb (4 kg)* Items Cotton or linen items that come into direct contact with the skin.
Program chart WetCare WetCare Sensitive Items Non-washable outerwear Note The garment is briefly dried and fluffed up WetCare Silks Maximum 5.5 lb (2.5 kg)* Maximum 5.5 lb (2.5 kg)* Normal, Hand iron plus, Hand iron Items Non-washable silk garments which crease easily WetCare Intensive Maximum 5.5 lb (2.5 kg)* Normal, Hand iron, Hand iron plus, Machine iron Items Washable outerwear Flatwork Cottons 40% residual moisture Maximum 17.6 lb (8 kg)* Cottons 25% residual moisture Maximum 17.
Program chart Special programs (3) You can put together 5 special programs and assign your own program names. Enter these into the tables. Load: Maximum 17.6 lb (8 kg) kg (weight of dry items) Example - [Special program 1] Dry+ - Res.
Changing the program sequence Payment system Opening the door or canceling the program after it has started may cause a loss of credit (depending on how the tumble dryer was set up*). * Either during the commissioning process or subsequently, Technical Service can reset the payment system so that programming changes can be made. Changing a program once it has started You cannot change to another program once a program has started (this prevents unintentional alterations).
Fragrance flacon Inserting a fragrance flacon Fragrance flacons (optional accessories) can be used to give your laundry a pleasant scent. Risk of fire and damage to the health if fragrance flacons are used incorrectly. The leaked fragrance can damage your health if it comes into contact with your body. Leaked fragrance can cause fire. Before using a fragrance flacon, please read “IMPORTANT SAFETY INSTRUCTIONS”, “Using the fragrance flacon (optional accessory)”.
Fragrance flacon Insert the fragrance flacon as far it will go into the socket. Turn the outer ring clockwise a little. The fragrance flacon may slip out. Turn the outer ring in such a way that the markers and line up. The markers and must line up with one another.
Fragrance flacon Opening the fragrance flacon Closing the fragrance flacon Before drying, you can select the intensity of the fragrance. After drying, the fragrance flacon should be closed to prevent the fragrance from escaping needlessly. Turn the outer ring clockwise: The further you open the fragrance flacon, the more intense the fragrance. Damp laundry and longer drying durations with sufficient heat transfer are needed for the fragrance to be released into the laundry effectively.
Fragrance flacon Removing/replacing the fragrance flacon Turn the outer ring counterclockwise until markers a and b line up. Replace the fragrance flacon with a new one. When not in use, you can store the fragrance flacon in its original packaging. Fragrance flacons are available to order from Miele dealers, Miele Service, or online. 48 The fragrance can leak out of the flacon. Do not lay the fragrance flacon down.
Cleaning and care When to clean This tumble dryer is equipped with a multi-stage filter system, which consists of lint filters (1.) and a filter in the toe-kick (2.). This filter system collects all lint generated during the drying process. 1. Cleaning the lint filters The lint filters are located in the drumloading area. Failure to clean the filter regularly could increase drying times. Fire hazard due to irregular maintenance.
Cleaning and care 2. Cleaning the toe-kick filter Damage caused by insufficient The filter in the toe-kick is behind the lint-filter flap on the bottom left. cleaning or by operation with a worn, damaged filter in the toe-kick. There is insufficient flow of air and heat in the heat exchanger due to clogging. This requires a visit from the Miele Service department. This can be avoided by following the advice in these operating instructions.
Cleaning and care 3. Cleaning the bottom-right grille/ heat exchanger for heat dissipation Clean only when Open bottom right grille, clean the heat exchanger appears in the display. The bottom-right grille can be removed. This covers the heat exchanger for heat dissipation. Keep the room where the tumble dryer is located free from dust and lint. Doing so will mean that you will rarely have to clean the grille. See “Bottom-right grille/heat exchanger”.
Cleaning and care Cleaning the lint filters This tumble dryer has 2 lint filters in the loading area. The upper and lower lint filters trap lint produced during the drying process. Removing the fragrance flacon The intensity of the fragrance will be diminished if the lint filters and the toekick filter are not cleaned. Remove the fragrance flacon as described in “Removing/replacing the fragrance flacon” under “Fragrance flacons”. Remove the lint (see arrows).
Cleaning and care Cleaning the lint filters and air-flow openings thoroughly If the drying duration has become longer or the surface of the filters is visibly compacted with lint, you should carry out the following cleaning procedure. Cleaning the lint filters while dry Pull the upper lint filter forward to remove it. Pull the lint filter forward to remove it. Turn the yellow knob until it clearly engages.
Cleaning and care Cleaning the lint filters with water Rinse the filter surfaces through under warm running water. Wipe the smooth plastic surfaces of both lint filters with a damp cloth to clean them. Wet lint filters could cause operational faults while drying. Shake the lint filters thoroughly and then dry them carefully. Push the upper lint filter in completely. Close the door. Push the lower lint filter in completely and lock it with the yellow knob.
Cleaning and care Cleaning the toe-kick filter The lint filter in the toe-kick collects finer lint, hair, and detergent residues that have got through the surfaces of the lint filters. Removing the lint filter Pull the lint filter out at an angle. Reach behind the catch with your finger. Open the lint-filter flap. Pull the handle out of the lint filter. Use the handle to pull out the lint filter at an angle forward and to the right.
Cleaning and care Cleaning the lint filter with water Clean the filter thoroughly under running water. Squeeze the filter very carefully several times as you rinse it. Rinse the filter until all visible residues have been removed. Damage caused by a insufficiently cleaned or damaged lint filter. If the filter has not been properly cleaned or is damaged, the heat exchanger will be clogged. There will be an insufficient flow of air and heat in the heat exchanger.
Cleaning and care Deformation Deformations indicate that the filter has become blocked and worn by continuous use. Cracks, tears, indentations White residues or residues of other colors Residues arise from laundry fibers and traces of detergent components which can clog the filter. They can be found on the front and side edges of the filter. In extreme cases, they can form stubborn crust.
Cleaning and care Cleaning the filter insert (in the toe-kick) The surface of the filter in the filter insert is visible after removing the lint filter in the toe-kick. This filter surface must only be cleaned if there is a visible accumulation of lint. Removing the filter insert If the filter insert is clogged up and soiled, it must be removed and cleaned under running water. Use the handle to pull out the filter insert at an angle forward and to the right.
Cleaning and care Checking the cooling fins on the heat exchanger Danger of injury caused by touching the cooling fins. You could cut yourself. Do not touch the cooling fins with your hands. After removing the filter insert, visually check the cooling fins on the heat exchanger. Check for any accumulation of lint. Risk of damage if cooling fins are cleaned incorrectly. The cooling fins can suffer damage or distortion. This could hinder the operational performance of the tumble dryer.
Cleaning and care Reinstalling the filter insert (in the toe-kick) Use the handle on the right to slide the filter insert at an angle behind the edge. Then press on the left handle until the filter insert is secured in position. 60 Press the frame of the filter insert in at the positions marked PUSH until it audibly engages. Reinstalling the lint filter (in the toe-kick) Place the lint filter back on the handle. Make sure it is the correct way round.
Cleaning and care Cleaning and closing the lintfilter flap Use the handle on the right to slide the lint filter at an angle behind the edge. Use a damp cloth to remove any lint. Make sure that you do not damage the rubber seal when doing this. Then press on the handle until the lint filter is secured in position. Close the lint-filter flap.
Cleaning and care Cleaning the bottom-right grille/heat exchanger Removing the grille The heat exchanger's cooling fins behind the grille can become blocked with dust and dirt drawn in from the surrounding area. Open the lint-filter flap. Open the bottom-right grille, e.g., using a spoon handle. Insert a spoon handle underneath the grille (under the recess ). Press and lever the grille gently until it opens on the left-hand side .
Cleaning and care Cleaning the cooling fins Replacing the grille Check whether the cooling fins are clogged. Danger of injury caused by touching the cooling fins. You could cut yourself. Do not touch the cooling fins with your hands. If there is visible soiling: Insert the grille on the right-hand side. Press the grille firmly on the left-hand side. Carefully vacuum up any visible lint or soiling. Use a dusting brush or the narrow crevice nozzle.
Cleaning and care Cleaning the tumble dryer Disconnect the tumble dryer from the electrical supply. Damage caused by the use of unsuitable care products. Unsuitable care products could damage plastic surfaces and other parts. Do not use any solvents, abrasive cleaners, glass cleaners, or allpurpose cleaners. Danger of electric shock caused by water. There is a risk of electric shock if water runs over or into the tumble dryer. Never spray the tumble dryer with water.
Frequently Asked Questions With the help of the following guide minor faults in the performance of the machine, some of which may result from incorrect operation, can be remedied without contacting the Service Department. This guide may help you to find the reason for the fault, and how to correct it. Program cancellation and fault message in the display Message Possible cause and solution In some programs, if the drum has been underloaded or is empty, the program will be canceled.
Frequently Asked Questions Message Possible cause and solution You have attempted to dry only a few items of varying size. A smaller item has been sucked into the loading area in the door. It is clogging the holes in the laundry deflector. To delete the message: touch the OK sensor control. Open the tumble-dryer door. Remove the item that is blocking the holes. Always dry small, individual items together with larger items. Rinse the lint filter and plinth filter. Check the airways.
Frequently Asked Questions Message Possible cause and solution The plinth filter looks clean after thorough cleaning. However, the program is canceled and the fault message appears again. The reason for this is that there is still underlying residue that cannot be removed. To delete the message: touch the OK sensor control. Replace the plinth filter with a new one. You can reactivate the removed, “old” plinth filter in the washing machine.
Frequently Asked Questions Messages in the display Message Possible cause and solution The heat exchanger’s cooling fins behind the grille can become blocked with dust and dirt drawn in from the surrounding area and the airways can become blocked with lint. Clean the heat exchanger. See “Bottom-right grille/heat exchanger” in “Cleaning and care”. Check and clean the filters in the loading area and in the toe-kick. To delete the message: touch the OK sensor control.
Frequently Asked Questions Unsatisfactory drying results Problem Possible cause and solution The laundry is not suffi- The load consisted of different types of fabric. ciently dry. Finish drying using the Timed drying warm air program. Large items of laundry have rolled up, causing a problem. The individual items of laundry are still damp. The laundry could not be untangled in the program you selected. Smaller items have rolled up into one. Untangle the laundry. Select the Large items program.
Frequently Asked Questions The drying-cycle duration is very long Problem Possible cause and solution The drying process goes on too long or even switches off*. The room where the tumble dryer is located is too warm. Ventilate the room thoroughly. Detergent residue, hair, and fine lint can clog the filters. Clean the lint filters and the filter in the toe-kick. See “Cleaning and care” for an in-depth description. If you have removed the plinth filter, also check the filter insert behind it.
Frequently Asked Questions General problems with the tumble dryer Problem Possible cause and solution You can hear buzzing or This is not a fault. The compressor (heat pump) is humming operating operating. noises. These noises are quite normal and can be heard when the compressor is operating. The drum lighting does not come on. The drum lighting switches off automatically when the door is closed.
Frequently Asked Questions Reactivating the plinth filter You can reactivate one or more dirty plinth filters in the washing machine. You will then be able to use the plinth filter again for a reasonable period of time. Wash the plinth filter(s) separately, not with any laundry items. Do not add any detergent. Tip: Select a short wash program with a maximum temperature of 104°F (40°C) and a maximum spin speed of 600 rpm. Select the Separate Rinse program, for example.
Customer Service Contact in the event of a fault Optional accessories In the event of a fault which you cannot remedy yourself, please contact your Miele dealer or Miele Customer Service. Optional accessories for this tumble dryer are available from your Miele dealer or Miele Technical Service. You can book a Miele Service Call online at www.miele.com/service. Contact information for Miele Customer Service can be found at the end of this document.
Installation instructions Alteration rights reserved. Visit our website for all the current product specifications, technical appliance information, and warranty information. To avoid accidents or damage to the appliance, please read these instructions before installing and/or using it.
IMPORTANT SAFETY INSTRUCTIONS , WARNING - Risk of Fire To reduce the risk of severe injury or death, follow all installation instructions. Clothes dryer installation must be performed by a qualified installer. Install the clothes dryer according to the manufacturer's instructions and local codes. Repair and maintenance work should be performed by a Miele authorized service technician. Work by unqualified persons could be dangerous and could void the warranty.
IMPORTANT SAFETY INSTRUCTIONS The installation of this unit in non stationary locations (e.g. ships) must be performed by a qualified installer or service agency, in strict accordance with national and local safety regulations and standards. Do not install the machine in rooms where temperatures below freezing may occur. This dryer is not intended for wall-insert. If there is any doubt concerning installation, contact Miele’s Technical Service Department. 1-800-999-1360 TechService@mieleusa.
*INSTALLATION* Installation and connection Front view a Drain hose for condensed water e Power cord b Control panel f Door c Lint-filter flap for the filter in the toe- g Bottom-right grille = Air-cooling kick opening – (open only when a prompt appears – (open only when a prompt appears in the display) in the display) d 4 height-adjustable screw feet 77
*INSTALLATION* Installation and connection Rear view a Interface for communicating with external appliances d Module slot (for external communication module) b Power cord e Drain hose for condensed water c Recesses under the protruding lid for transporting the appliance 78
*INSTALLATION* Installation and connection Installation locations View from above All measurements are in inch (mm). The distances between the machine and the wall are recommendations to help make it easier to carry out service work. If installation space is limited, the machine can also be pushed up against the wall. Side view Washer-dryer stack Steel toe-kick A stacking kit* is required. This must be installed by a service technician authorized by Miele.
*INSTALLATION* Installation and connection Transporting the tumble dryer to its installation site Damage caused by incorrect transportation of the tumble dryer. If the tumble dryer tips over, there is a danger of injury to people and damage to property. Ensure that the tumble dryer is stable during transportation. Transporting the tumble dryer If the tumble dryer is being transported on its side, it must be tipped onto its left or right side.
*INSTALLATION* Installation and connection Installation Ensure that no closeable door, sliding door, or an oppositely hinged door is installed that would hinder the door of the dryer being opened in any way. Downtime after installation Damage caused by switching the appliance on too soon. This can damage the heat pump. After setting up the tumble dryer, wait for at least one hour before switching it on. Leveling the tumble dryer The screw feet can be adjusted to compensate for unevenness in the floor.
*INSTALLATION* Installation and connection Room ventilation External control equipment - Air drawn in for use in the drying process will be warm when it is expelled back into the room. You must therefore ensure that the room is sufficiently ventilated, particularly if the dryer is located in a small room. An optional accessory unit has to be purchased to set up a connection with external systems: - Make sure that the room temperature is not too high.
*INSTALLATION* Installation and connection Drain hose for condensed water The condensed water is pumped away through the drain hose which is located at the back of the dryer. Laying the drain hose Damage to the drain hose due to incorrect handling. The drain hose can suffer damage and leak. Do not pull on the drain hose and do not stretch it or allow it to become kinked. Inserting the drain hose into a standpipe Insert the end of the drain hose into the standpipe.
*INSTALLATION* Installation and connection Electrical connection This description applies to tumble dryers both with and without an electrical plug. The following applies to tumble dryers with an electrical plug: - This tumble dryer is supplied with a power cord and plug ready for connection. - The electrical socket must be easily accessible so that the tumble dryer can be disconnected from the electricity supply. Damage caused by incorrect supply voltage.
Technical data Height 2' 9 7/16" (850 mm) Width 1' 11 7/16" (596 mm) Width (only for appliances with a stainless steel lid) 1' 11 13/16" (605 mm) Depth 2' 3 9/16" (777 mm) Depth with door open 3' 10 7/8" (1191 mm) Weight 165 lb (75 kg) Drum volume 34.3 gal (130 l) Load quantity 17.
Supervisor level Opening the supervisor level 11:02 Programs Favorites Supervisor Help Touching the sensor control takes you to the supervisor level. Access via code The supervisor level is accessed using a code. Factory default: The code is 000. Demo program In showrooms, a demo program can be started with a simulation. A program does not start. The operational sequence is simply a simulation.
Supervisor level Language entry The display can be set to one of several different user languages. This setting allows you to determine how languages can be selected. You can change the language as follows: International 6 languages are available. The sensor control is not active. Note the setting Set languages. Set languages The languages for the setting Language entry International can be changed. 6 languages can be selected. All languages are available.
Supervisor level Clock display After selecting the clock format, you can set the time of day. Clock format - Factory default: 24-hour display - 12-hour display - No clock Set - The time can be set. Date The date can be set after selecting the date format. - Date format The date can be shown starting with the day, month, or year. - Date The date is set. Volume The volume for various sounds can be changed. The volume can be changed.
Supervisor level Display off status The display switches off to save energy; only the Start/Stop sensor control flashes slowly. You can change this setting. Changing this setting leads to increased energy consumption. - Off No switching off Machine off status In order to save energy, the tumble dryer will switch off automatically after the end of the program or if no further selection is made. You can change this setting. Changing this setting leads to increased energy consumption.
Supervisor level Memory The tumble dryer saves the settings that were selected last for a drying program (drying level and/or extra option, or the duration for some programs). - Factory default: Off - On Temperature unit You can select the unit for the temperature display. - Factory default: °C / Celsius - °F / Fahrenheit Weight unit You can decide whether load quantities are displayed in “kg” or “lb”.
Supervisor level Program selection Controls - Standard Factory default: all (selected) programs are available. You can select whether the tumble dryer is operated as a “laundromat” machine. Shortcuts are the easiest way to operate the machine. Operating staff are unable to change pre-set programs. - Laundromat, basic Tip: Start by configuring all necessary settings and changes to the tumble dryer before adjusting any of the options below.
Supervisor level - Laundromat Logo int. time 4 time programs* with different temperature levels are timecontrolled via the tumble dryer’s electronic. The maximum laundry weight is 17.6 lb (8 kg) kg. The set value indicates the maximum program duration and can be modified by the user. * The maximum program duration is specified during initial commissioning. - External prog. selection A communication module can be used to select the program from an external terminal.
Supervisor level Favorite programs After switching on, you can also select a program via: Favorites. 12 programs can be stored as favorites based on your own priorities and requirements. These favorite programs will also be made available in the - Laundromat Logo - Laundromat, basic control options. You can specify the control option under Controls. Tip: You can assign a different color to each program. In this case, the Program color allocation setting must be set to On.
Supervisor level An orange border appears around the selected program. Touch the program with your finger and keep your finger pressed down. Drag the program to the required place.
Supervisor level Special programs You can put together 5 special residual-moisture or time-controlled programs and assign your own program names. First, enter the program name. Select the special program you want to change. Res. moisture program - Final residual moisture: - 6% (dry) – 40% (damp) - Extra drying time: 0–60 minutes - Temperature (Process air): cold – 158°F (70°C) The Save as menu opens.
Supervisor level Timed drying Sort programs - Running time: 1–120 minutes Programs can be moved within the program list and in the Favorites list. - Temperature (Process air): cold – 158°F (70°C) - Factory default: Off - Drum rotation main direction: 0–600 seconds Select the “On” option. - On - Drum reversal: 0–600 seconds Exit Supervisor level. - Cooling down temp. (Process air): 104-131°F (40–55°C) Touch the program that you wish to move.
Supervisor level Process technology Anti-crease At the end of the program, the drum will continue to rotate at intervals if the laundry is not removed immediately. Additional cooling Before the end of the program, the temperature of the dried laundry is monitored and the cooling phase at the end of the program is extended if necessary. Changing this setting leads to increased energy consumption. Changing this setting leads to increased energy consumption.
Supervisor level Service Clean out the airways The tumble dryer's electronic calculates the degree at which lint or detergent residue in the lint filters and air ducts are impairing performance. A message to check the contamination appears. You can decide at what level of lint this reminder should be emitted. This prompt, which you can configure, is displayed: Clean the lint filter and rinse the . plinth filter - Off The reminder does not appear.
Supervisor level External applications Peak load signal External hardware is connected via the Miele XCI Box. The peak-load negotiation function enables the tumble dryer to be connected to an energy-management system. When a signal is registered, the tumble dryer's heater is switched off for a short period or the appliance is prevented from being switched on. The tumble dryer may only be operated with a peak-load system if this system is connected to the tumble dryer via the Miele XCI Box.
Supervisor level WiFi / LAN For the use of WiFi / LAN additional Miele digital products are necessary. The ability of Miele digital products depends on the availability of the services in your country. The different services are not available in all countries. For information about availability, please visit www.miele.com. Control the networking of your tumble dryer. - Setup This message only appears if the tumble dryer has not yet been connected to a WiFi network.
Supervisor level WiFi setup Factory default: Off There are 2 possible connection methods. Via WPS Activate the WPS function on your router within 2 minutes. Tip: If the connection has not been set up when the timeout has finished counting down, repeat the process. via Soft AP Activate the function with the Miele app on your smart device within 10 minutes. Network time The date and time can be synchronized over the network. - Off The date and time are not synchronized over the network.
Supervisor level Remote Update Running a RemoteUpdate The RemoteUpdate function is used for updating the software in your tumble dryer. If a RemoteUpdate is available for your tumble dryer, it will be displayed automatically when the supervisor level is open. Factory default: On If you do not install a RemoteUpdate, you can continue to use your tumble dryer in the usual way. However, Miele recommends installing RemoteUpdates.
Supervisor level Machine parameters Legal Information Open Source Licenses You can view information here. Copyrights and licenses for operator and control software Miele uses their own and third party software which is not subject to any socalled open source license for the operation and control of the device/ appliance. This software/these software components are protected by copyright. The copyright powers of Miele and third parties have to be respected.
Supervisor level External program lock The control unit has an option to block programs. Programs are blocked by an external system via the COM interface. A program can be blocked based on the available time or the available account balance, or generally. - Factory default: Off - On Feedback sig. to pay system Setting the feedback signal for the coin box. - Factory default: Off - Program end The feedback signal is sent at the end of the program.
Supervisor level Debounce time In coin-box mode, the debounce time for the minimum payment signal that must be applied can be adjusted. - Factory default: Short For coin boxes where the falling coin generates the paid pulse. - Long For central control units on a 230 V basis. Pay system override time Setting the transition signal for the coin box. Security time margin to prevent the coin box being tampered with.
Please have the model and serial number of your machine available when contacting Technical Service. U.S.A. Miele, Inc. National Headquarters 9 Independence Way Princeton, NJ 08540 Phone: 800-991-9380 www.mieleusa.com/professional prosales@mieleusa.com Technical Service & Support Phone: 800-991-9380 proservice@mieleusa.com Miele & Cie.
PDR 908 HP en-US M.-Nr.