Operating Instructions Commercial Dishwasher PG 8083 SCVi To prevent accidents and machine damage read these instructions before installation or use. en - US M.-Nr.
Contents Guide to the manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Guide to the commercial dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Control panel . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Adding detergent. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Turning the dishwasher on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contents Factory default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Select last program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Temp. display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 To close the Settings menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Cleaning and care . . . .
Guide to the manual Warnings and notes Warnings ,Warnings marked like this contain safety information concerning potential injury and damage. !Read the warnings carefully and follow the instructions and directions. Notes Notes contain information that is particularly important to follow. Additional information and comments Additional information and comments are contained in a simple frame. They are not imperative.
IMPORTANT SAFETY INSTRUCTIONS WARNING When using your dishwasher follow basic precautions, including the following: This dishwasher is intended for household and commercial applications. Only use the machine for its intended purpose. Any other use, conversion or modification is dangerous. This dishwasher complies with current safety requirements. Improper use of the machine can lead to personal injury and material damage. Read all instructions before installing or using this machine.
IMPORTANT SAFETY INSTRUCTIONS Proper installation ~ Do not use the machine until properly installed. ~ Do not install the machine in an area where a danger of explosion or of freezing temperatures may be present. ~ To ensure the stability of undercounter dishwashers, they must only be installed beneath a continuous countertop that is bolted to the adjacent cabinetry.
IMPORTANT SAFETY INSTRUCTIONS ~ Be sure to follow the installation instructions in this manual and in the installation diagram. ~ Before connecting the appliance, ensure that the connection data on the data plate (voltage, frequency and fuse rating) match the building's electrical supply. ~ WARNING - Fire hazard! Do not cover or crush the plug of the appliance. Ensure that the cabinet opening for the dishwasher provides ample space for the plug and cord.
IMPORTANT SAFETY INSTRUCTIONS Proper use ~ The dishwasher is designed only for operation with water and the appropriate cleaning agents. Organic solvents must not be used in the machine. An explosion or machine corrosion could occur with the use of organic solvents. Follow the instructions and relevant safety procedures carefully. ~ Only use standard household mechanical dishwasher detergents in this unit. Keep all cleaning agents out of the reach of children.
IMPORTANT SAFETY INSTRUCTIONS ~ Avoid inhaling detergent. If swallowed, it can cause burning in the mouth and throat or inhibit breathing. ~ Observe the detergent manufacturer's directions for storage, use and dosage of cleaning agents. ~ Never clean the machine or near its vicinity with a water or high pressure hose. ~ Accessories ~ Only specific additional equipment, made by Miele or approved by Miele, should be used with this machine. Consult Miele on the type and application of such equipment.
Guide to the commercial dishwasher Overview a Upper spray arm (not visible) g Filter combination b Cutlery tray h Data plate c Upper basket i Optical interface d Middle spray arm j Rinse aid reservoir e Air inlet for drying k Dual-compartment detergent dispenser f Lower spray arm l Reservoir for regenerating salt 11
Guide to the commercial dishwasher Control panel a Display e Program selection b 4 ü button, (other programs) with indicator light f Program button for program selection c Delay start button with indicator light g - button (On/Off) with indicator light d Extra drying button with indicator light 12 h Optical interface
Help to protect the environment Disposal of the packing material The cardboard box and packaging protect the appliance during shipping. These materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old machine Old appliances may contain materials that can be recycled.
Help to protect the environment Energy saving washing This dishwasher is exceptionally economical in the use of water and electricity. For best results follow these tips: ^ You may connect the commercial dishwasher to a hot water line. This is particularly suitable with energy-saving water heating sources such as solar energy systems. If the hot water system is electrically heated and if loads comprise primarily glassware we recommend connecting the appliance to the cold water line.
Before using for the first time Opening the door Closing the door ^ Push the baskets in. ^ Push the door until it clicks shut. ,Keep your fingers off the door frame. Risk of injury! At the end of programs with a drying cycle (see Program guide) the door will automatically open a little in order to improve the drying. You can cancel this function (see Settings menu - AutoOpen drying). ^ Pull the handle to open the door. If the door is opened during operation the dishwasher will automatically stop running.
Before using for the first time Display General Settings menu The following functions can be selected or set with the display: The Settings menu allows you to set the dishwasher to suit your requirements. See "Settings" for more information.
Before using for the first time Basic settings ^ Press the - button to turn the dishwasher on. If the dishwasher is being turned on for the first time, the welcome screen will appear. It is useful to know your water hardness so that you can provide the service technician with this information in the event of any service calls. Please note your water hardness below: °d (gr/gal) Language The display automatically switches to the language setting. See "Display" for details.
Before using for the first time Every dishwasher is tested before leaving the factory. Any water remaining in the machine is from the final factory test and does not indicate that the machine has been used. Filling the salt container To achieve good cleaning results, the dishwasher needs soft water (water that is low in minerals). Hard water results in calcium deposits on dishware and in the dishwasher. Therefore, tap water with a hardness of 4 °d (4 gr/gal) or more must be softened.
Before using for the first time ^ Only open the door half way when adding salt to avoid spilling it. ^ Press the button on the top of the salt reservoir in the direction of the arrow. The cover will pop open. Do not fill water into the salt reservoir! ^ Only add just enough salt to fill the reservoir. Depending on the type of salt, the reservoir will hold up to approx. 2.2 lbs (1 kg). Never fill with more than 2.2 lbs (1 kg) of salt. Displaced water may run out as the reservoir is being filled.
Before using for the first time Refill salt indicator ^ Refill the salt reservoir as soon as the F Refill salt message is displayed. ^ Press the center button to confirm. The Refill salt indicator goes out. If a sufficiently high concentration of salt has not yet formed, Refill salt may continue to be displayed after adding the salt. In this case, confirm again with the center button. The Refill salt message is turned off if you have programmed the dishwasher to a water hardness below 4 °d (4 gr/gal).
Before using for the first time Rinse aid Rinse aid helps to prevent spotting on dishes and glassware and speeds up the drying process. The rinse aid is filled into the reservoir and the set amount will be automatically dispensed. ,Use rinse aid only. Never fill the rinse aid reservoir with regular dishwashing detergent or cleaning agent. This will damage the rinse aid reservoir. Adding rinse aid ^ Pour rinse aid into the reservoir until it is visible in the opening.
Loading the dishwasher Tips: Remove coarse food residues from the dishware. There is no need to rinse items before loading into the dishwasher. ,Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher. These materials damage the dishwasher. All items can be placed anywhere in the baskets. However, note the following: – Do not place dishes or cutlery inside other pieces. They will cover each other. – Load dishes so that water can reach all the surfaces.
Loading the dishwasher Items not recommended for dishwashing: – Wooden cutlery and dishes or items with wooden parts: they discolor and fade. In addition, the glue used in these items is not dishwasher-proof. Result: wooden handles may come loose. – Hand-crafted items, antiques, valuable vases and decorative glassware: these items are not dishwasher-proof. – Plastic items which are not heat resistant: these items may become deformed.
Loading the dishwasher Typical load for 10 place settings with cutlery tray Upper basket Cutlery tray 24 Lower basket
Loading the dishwasher Typical load for 16 place settings with cutlery tray Upper basket Lower basket Cutlery tray 25
Loading the dishwasher Upper basket ,Always use the dishwasher with the upper and lower basket inserted. ^ Load the upper basket with small, lightweight, or delicate items such as cups, saucers, glasses, dessert bowls, etc. Shallow pans can also be placed in the upper basket. ^ Long items such as soup ladles, mixing spoons and long knives should be placed lying down across the front of the upper basket.
Loading the dishwasher Jumbo cup rack The cup rack can be set to two different widths so that it can also accommodate large cups. ^ If necessary, move one of the side inserts in the cutlery tray to make room for tall glasses. Adjusting the height: You can set the support bar to two different heights. ^ Pull the cup rack upwards and click it back into position at the required width. Universal support bar The support bar will hold tall glasses and stemware securely.
Loading the dishwasher Adjusting the upper basket In order to gain more space for taller items in the lower or upper basket, the upper basket can be adjusted to three levels of about 2 cm height difference between each level. The upper basket can also be set at an angle with one side high and the other side low to improve water drainage. However, make sure that the basket can slide smoothly in and out of the cabinet. ^ Pull the upper basket out.
Loading the dishwasher Lower basket ^ Place larger and heavier items such as plates, serving platters, saucepans, bowls, etc. in the lower basket. It can also be used for glasses, cups, small plates and saucers. Heavily soiled items Commercial dishwasher with cutlery tray ^ Place very large plates in the center of the lower basket. When tilted, plates up to 13 3/4" (35 cm) in diameter can be accommodated.
Loading the dishwasher Removable MultiComfort insert Glass rack The rear section of the lower basket is used for cups, glasses, plates, pots and pans. ^ The glass rack can be folded up to make more room for tall items. You can remove the MultiComfort insert to make more space for larger items such as pots and pans. ^ Stemware, e.g. wine, champagne and beer glasses, can be leaned against the glass rack or suspended from it. The height of the glass rack is adjustable.
Loading the dishwasher Glass rack The glass rack can hold tall glasses and stemware securely. ^ Press the yellow lever down a and fold the spikes down b. ^ Fold the support bar down and lean the glasses against it. Foldable spikes Bottle holder The bottle holder is for washing narrow items e.g. for milk bottles or baby bottles. The spikes at the front are used for plates, soup bowls, platters, desert bowls, and saucers. Both rows of spikes can be folded down to create more room for larger dishware, e.g.
Loading the dishwasher Cutlery Split cutlery tray If spoon handles do not fit between the holders, put them the other way round. ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery can be grouped in zones, one for knives, one for forks, one for spoons, etc. Spoon heads should be placed in contact with at least one of the serrated retainers on the base of the cutlery tray to ensure that the water runs off them. Make sure that large items (e.g. cake servers, etc.
Optional accessories Optional dishwasher accessories are available from your Miele dealer, Miele or Mieleusa.com (depending on your model some may already be supplied with your machine as standard). If you would like to... the following accessory will need to be ordered... ...wash a Miele Cappuccinatore ... a Cappuccinatore insert for the upper basket. ...wash additional items of cutlery ... a cutlery basket for the lower basket. ...wash long-stemmed glassware ...
Use Detergent ,Avoid inhaling powder detergents. Avoid swallowing dishwasher detergent! Detergents can cause chemical burns to nose, mouth and throat. Consult a doctor immediately if detergent has been swallowed or inhaled. Powder detergents Use only powder detergent in the dispenser in the door. ^ Pour powder detergent into the compartments of the detergent dispenser. Detergent dosage ,Always keep detergent out of the reach of children. Keep children away from the dishwasher when the door is open.
Use Adding detergent Detergent dosing aid Compartment I holds a maximum of 2 teaspoons (10 ml), compartment II holds a maximum of 3.5 tablespoons (50 ml) of detergent. The horizontal marks in compartment II indicate the levels of approximately 1 ¼ and 2 tablespoons (20 and 30 ml) respectively. The marks indicate the approximate fill level in ml when the door is open in a horizontal position. ^ Press the button on top of the detergent dispenser. The cover will pop open.
Use Turning the dishwasher on Starting a program ^ Open the water supply if it is closed. ^ Close the door to start the program. ^ Open the door. The optical interface lights up to confirm the start of a program sequence. If additional functions are selected, the corresponding indicator lights will also come on. ^ Make sure the spray arms can rotate freely. ^ Press the - button to turn the dishwasher on.
Use Time display Standby Before the program starts, the time display shows the runtime of the selected program in hours and minutes. The remaining time is displayed during the program. A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The display and the indicator lights are turned off and only the indicator light flashes slowly.
Use End of program Turning the dishwasher off At the end of a program, the optical interface flashes with the door closed. At the end of a program: The program has finished when O End or AutoOpen is displayed and the door is slightly ajar. ^ Press the - button to turn the dishwasher off. If Extra drying was selected and AutoOpen is active, the drying fan will run for a few minutes after the program has ended. ^ Open the door all the way to reset the door latch. ^ Unload the dishwasher.
Use Interrupting a program A program will be interrupted as soon as the door is opened. When the door is closed again, the program will continue from where it was interrupted. ,Water in the dishwasher is hot. Danger of scalding. Only open the door if absolutely necessary and exercise extreme caution when doing so. Before closing the door again, leave it ajar for approx. 20 seconds. This will enable the temperature in the wash cabinet to settle. Close the door firmly until it clicks into place.
Program guide Program Application Detergent Follow the detergent manufacturer's instructions Compartment I 1) ProSpeed Compartment II 1) For fresh, non-sticky food residues 1 oz Universal For normal, slightly dried food residues 1 oz Pots & Pans For burned-on, very adherent, very dry, starchy or albuminous 1) food residues. 1/3 oz China & Crystal Special glassware program Sanitize Special hygiene program for dishware requiring a high degree of hygiene.
Program guide Program sequence Prerinse Main wash Interim rinse I Interim rinse II2) Final rinse X 149°F (65°C) 1 min X (X) X 149°F (65°C) 10 min X 8 min X 167°F (75°C) 10 min X 122°F (50°C) 1 min X 8 min X X 167°F (75°C) 10 min X 122°F 10 min (50°C) 1 min Extra drying Auto Open Water plus X 149°F (65°C) 3) 30 s (X) 4) (X) (X) X 149°F (65°C) 3) 1.5 min (X) (X) (X) (X) X 149°F (65°C) 3) 1.
Program guide Program When to use Detergent Follow the detergent manufacturer's instructions Compartment I 1) Compartment II 1) Glass no rinse aid (beer glasses) Special program without rinse aid, recommended for beer glasses. (The glasses do not dry through their own heat after the program has ended and might have to be dried by hand). Normal *) Program for completely washing a full load of normally soiled dishware. Standard program for washing normally soiled dishes.
Program guide Program sequence Prerinse Main wash Interim rinse I X 122°F (50°C) 1 min X X 103°F (41.5°C) 47 min 3 min X 3 min Interim rinse II2) Final rinse Drying Extra drying Auto Open Water plus X —5) 1 min X X 106°F (49.5°C) 45 min 5 min (X) X Cold 8 min X = part of the program (X) = additional, optional program steps 2) Interim rinse II, must be programmed by a Miele service technician. 3) Optional temperature increase to 167°F (75°C).
Program guide Consumption 6) Program Electrical energy Water cold 15°C Water hot 55°C 1.7 kWh 0.9 kWh 1.7 kWh Time 6) Water Water cold 15°C Water hot 55°C 17 l 35 min 7) 25 min 7) 1.0 kWh 17 l 48 min 7) 38 min 7) 2.0 kWh 1.0 kWh 23 l 64 min 7) 52 min 7) 1.1 kWh 0.4 kWh 17 l 29 min 7) 20 min 7) 2.3 kWh 1.3 kWh 23 l 101 min 89 min 1.4 kWh 0.5 kWh 23 l 94 min 81 min 0.7 kWh 0.4 kWh 17 l 24 min 19 min 1.2 kWh 0.5 kWh 17 l 124 min 115 min 0.03 kWh 0.
Additional options Extra drying For better drying results and to reduce the amount of steam that escapes when the door is opened, the Extra drying function extends the fan runtime at the end of the program. This function is not available for all programs. When Extra drying is selected, the total program runtime will increase by approx. 20-30 minutes, depending on the program. ^ Open the door. ^ Press the - button to turn the dishwasher on. The - indicator light comes on. ^ Select the desired program.
Additional options Delay start The start time of a program can be delayed from 30 minutes to 24 hours. The delay is set in 30 minute increments. When using the Delay start function, make sure that the detergent compartment is dry before adding detergent. Wipe dry if necessary. Otherwise the detergent could clump and not rinse out completely. ^ Open the door. ^ Press the - button to turn the dishwasher on. The - indicator light comes on. ^ Use the Program button to select the desired program.
Additional options BrilliantLight The commercial dishwasher is equipped with interior lighting. The lighting switches off automatically when the door is open for longer than 15 minutes. You can permanently switch off the interior lighting. ^ Swing the door of the dishwasher halfway open and closed quickly three times. Move the door far enough that the interior lighting goes on and off. This permanently switches off the interior lighting. ^ Do the same again to reactivate the lighting.
Settings Settings menu for changing standard settings Opening the Settings menu ^ If the dishwasher is on, press the button to turn it off. ^ Press and hold the X button. ^ Press the - button to turn the dishwasher on, and hold the X button down for at least 4 more seconds. The first option of the Settings menu appears in the display and all the indicator lights comes on. See the "Display functions" section for details. ^ Select the menu setting you wish to change.
Settings Water hardness Your dishwasher comes with with a water softener. You must set the system to the water hardness level of your water supply. – The dishwasher must be programmed to exactly match the hardness of your water. – Your local waterworks can tell you the water hardness level in your area. – Where the water hardness fluctuates always program the dishwasher to the higher value. The set water hardness is marked with a check (.
Settings Rinse aid Buzzer For best results the rinse aid dosage can be adjusted. The dosage can be set between 0-6 ml. The factory setting is 3 ml of rinse aid. If activated, the buzzer sounds at the end of a program and when a fault occurs. – Use a higher setting if spots appear on dry glassware. – Use a lower setting if streaking appears on dishes or glasses. ^ Select the desired amount of rinse aid and press the center button to confirm.
Settings AutoOpen Optimize Standby To improve drying, the door automatically opens a little at the end of a program, except for Pre-rinse, Short and Beer glasses (see Program guide). A few minutes after the last button is pressed or a few minutes after the end of the program the dishwasher will switch to Standby mode to save energy. The display and the indicator lights are turned off and only - flashes slowly.
Settings Filter check The refill messages can be turned off without first refilling to let the dishwasher go into Standby mode. But the fault messages cannot be turned off. Refill messages You can set the length of the interval between filter checks as a reminder. You can set an interval between 30 and 60 wash cycles. The factory setting is an interval of 50 wash cycles. If you want the dishwasher to switch to Standby mode in spite of a refill message, you can switch both indicator lights off together.
Settings Detergent dosage This function becomes visible when External DOS is activated. Venting the DOS system The DOS system will not dispense reliably if there is air in the system. The DOS system must be vented You can set the detergent dosage in milliliters or percent according to the manufacturer's instructions if you have installed the DOS module G 60 Semi for liquid detergent. – Unit of measurement in ml The factory setting is 30 ml. The dosage can be set from 10 - 100 ml in 2 ml increments.
Settings High temp rinse For better drying, the rinse temperature can be increased. This function is not available for all programs (see "Program guide"). ^ Select the desired setting and press the center button to confirm. Water plus When selected, more water will be used for the wash cycle. This function is not available for all programs (see "Program guide"). ^ Select the desired setting and press the center button to confirm.
Settings Factory default Temp. display You can reset all settings back to the factory default settings. An activated External Dos and its respective amount of detergent or dosage concentration will not be reset. During a program the current temperature is displayed as factory default setting. If the temperature display is turned off the remaining run time is being displayed during a program. ^ Select Reset and press the center button to confirm.
Cleaning and care Check the overall condition of your dishwasher regularly (approx. every 4 - 6 months). This will help to prevent problems. ,The outer surfaces of the dishwasher are susceptible to scratching. Contact with unsuitable cleaning agents can alter or discolor the outer surfaces. Cleaning the wash cabinet The wash cabinet is largely self-cleaning, provided that the correct amount of detergent is used.
Cleaning and care Cleaning the control panel and exterior ,Remove any soiling immediately. Otherwise it might become impossible to remove and could cause an alteration or discoloration of the surfaces. ^ Clean the control panel with a moist cloth only. ^ Clean the front of the appliance with a clean sponge, liquid dish soap and warm water. Then wipe dry with a soft cloth. To clean, you can also use a clean, damp microfiber cloth without detergent. Glass cleaners may be used to clean the exterior.
Cleaning and care Triple filter system Cleaning the filters The triple filter system in the base of the wash cabinet retains coarse dirt from the suds solution, preventing it from reaching the circulation system and re-entering the cabinet through the spray arms. ^ Turn the dishwasher off. ,The dishwasher must not be used without all the filters in place. Collection of coarse dirt may cause the filters to clog.
Cleaning and care The cover must be opened to clean the inside of the filter: ^ Replace the triple filter so it lies flat in the base of the wash cabinet. ^ Push the clips together in the direction of the arrows as shown a, and open the cover b. ^ Lock the filter by turning the handle clockwise, until the arrows point to each other. ^ Clean all parts under running water. ,The triple filter system must be ^ Close the cover so that the lock engages. inserted correctly and locked.
Cleaning and care Cleaning the spray arms ^ Remove the lower basket. Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be checked regularly (approx. every 4 - 6 months). ^ Turn the dishwasher off. Remove the spray arms as follows: ^ Pull out the cutlery tray (if present). ^ Pull the lower spray arm firmly upwards to remove. ^ Push the upper spray arm up to engage the inner ratchet and unscrew the spray arm.
Frequently asked questions ,Repairs should only be carried out by a qualified and trained person in accordance with local and national safety regulations. Unauthorized repairs could cause personal injury or machine damage. Technical faults Problem The dishwasher does not start. Possible fault The door is not properly closed. The dishwasher is not plugged in. The circuit breaker has tripped. The dishwasher is not turned on. The dishwasher stops The circuit breaker has during a program. tripped.
Frequently asked questions Problem Possible fault Before fixing the fault: – Press the - button to turn the dishwasher off. The optical interface flashes fast. The buzzer sounds. One of the following fault messages is displayed: ; Fault FXX There may be a technical fault. L Waterproof The waterproof system has activated. 62 Solution After a few seconds: – Turn the dishwasher on. – Select the desired program. – Close the door. If the error message is displayed again, there is a technical fault.
Frequently asked questions Faults in the water intake or water drain Problem The optical interface flashes fast. The buzzer sounds. One of the following fault messages is displayed: Possible fault Solution 2 Open the water supply The water supply is closed. Open the water supply all the way. 2 Water intake Before fixing the fault: – Press the - button to turn the dishwasher off. There is a problem with – Open the water supply all the water intake. the way.
Frequently asked questions Problem The optical interface flashes fast. The buzzer sounds. One of the following fault messages is displayed: 2 Water drain 64 Possible fault Solution Before fixing the fault: – Press the - button to turn the dishwasher off. Fault in the water – Clean the triple filter system drainage. (see "Cleaning and care"). There might be water in – Clean the drain pump (see the wash cabinet. "User maintenance instructions").
Frequently asked questions General problems with the dishwasher Problem The indicator lights and the display are dark. Only the indicator light flashes slowly. Possible fault Solution The indicators and the display turn off automatically to save energy (Standby). Press the - button to come out of Standby mode. The interior lighting does not come on when the door is opened. The following fault message is displayed: The interior lighting was Turn the interior lighting back permanently turned off.
Frequently asked questions Problem Possible fault Solution There are detergent residues in the dispenser at the end of a program. The detergent dispenser cover will not close. The inside of the door and/or the interior walls are wet after a program has finished. The dispenser was wet when detergent was added. Make sure the dispenser is dry before adding detergent. Detergent residue is blocking the latch. This is normal! Remove the detergent residue. None. The moisture evaporates after some time.
Frequently asked questions Noises Problem There is a knocking noise in the wash cabinet. There is a rattling noise in the wash cabinet. There is a knocking noise from the water pipe Possible fault A spray arm is hitting the dishware. Dishware is moving around in the wash cabinet. A foreign object has become lodged in the drain pump. Solution Interrupt the program and rearrange items blocking the spray arms. Interrupt the program and rearrange loose pieces.
Frequently asked questions Poor cleaning results Problem Possible fault The dishes are not The dishes were not loaded clean. correctly. The program was not suitable for the requirements. Solution See "Loading the dishwasher". Select a more suitable program (see "Program guide"). Not enough detergent was Use more detergent, or dispensed. switch to another detergent. The spray arms are blocked Check by turning the spray by dishware. arms and rearrange the dishes if necessary.
Frequently asked questions Problem Possible fault Dishes are not dry, The rinse aid dosage is set or glasses and too low or the rinse aid cutlery are spotty. reservoir is empty. White residue is visible on the dishware. Clouding occurs on glassware and cutlery; the deposit can be wiped off. The dishes were taken out too soon. The rinse aid dosage is too low. The salt reservoir is empty. The water softener setting is too low.
Frequently asked questions Problem Possible fault Solution Glasses have a brownish-blue discoloration; the deposit cannot be wiped off. Detergent deposits. Switch to another detergent right away. Glasses are dull and discolored; the deposit cannot be wiped off. Tea or lipstick stains have not been completely removed. The glasses are not dishwasher-safe. Surface changes occur. There is no remedy. Use only dishwasher-safe glasses. The wash temperature of the selected program was too low.
User maintenance instructions Cleaning the water supply screen There is a screen in the screw connection of the water inlet hose to protect the water inlet valve. The screen must be cleaned when dirty, otherwise insufficient water will flow into the wash cabinet. ,The plastic housing of the water connection contains an electric valve. The housing must not be immersed in water.
User maintenance instructions Cleaning the drain pump and non-return valve The drain pump is located beneath the non-return valve (arrow). If there is still some water in the wash cabinet at the end of a program, the water was not pumped out properly. The drain pump or the non-return valve might be clogged. However, they are easy to clean. ^ Disconnect the dishwasher from the electrical power supply. Always turn the appliance off before unplugging it.
After sales service Repairs In the event of a fault which you cannot correct yourself please contact the Miele Service Department at the phone number on the back of this booklet. ^ Please quote the model type and number of your appliance. These can be found on the data plate along the right edge of the door. PC Update The Program Correction (PC) allows a technician to update the dishwasher to make use of new technology.
Electrical connection ,All electrical work must be performed by a qualified service technician in accordance with local and national safety regulations. – The electrical connection is made through a plug and outlet according to national requirements. The outlet has to be easily accessible after installation. This facilitates access for electrical safety checks, for example when the appliance is being repaired or serviced.
Electrical connection The PG 8083 SCVi comes equipped with a 14/3 AWG cord for connection to a standard AC 120 V, 60 Hz power outlet with a NEMA 5-15P plug or with a 10/4 AWG cord for connection to a 2N AC 208/240 V, 60 Hz power supply with a NEMA Type 14-30P plug. 120V 208-240V Rated Load (kW) 1.3 5.
Plumbing The Miele waterproof system Providing the dishwasher was installed correctly by a qualified technician, the waterproof system will protect you from water damage throughout the lifetime of the machine. Connection to the water inlet This machine must be connected to the water supply in accordance with all national and local plumbing codes. ,Water in the machine is not suitable for drinking. – Valves with 3/4" male thread are to be provided on site.
Plumbing Water drainage Venting the drainage system – The drain is equipped with a non-return valve which prevents waste water from flowing back into the dishwasher through the drain hose. The drain must be vented if the connection to the building' s drainage system is lower than the roller guides for the lower basket in the door. Otherwise the water inside the dishwasher may siphon out during the wash program. – The dishwasher drain hose should be connected to a separate drain for the dishwasher only.
Technical data Model Commercial dishwasher PG 8083 SCVi Height 33 1/4" (84.5 cm) [adjustable +2 9/16" (6.5 cm] Installation height min. 33 1/4" (84.5 cm) [+2 9/16" (6.5 cm)] Width 23 3/16" (59.8 cm) Installation width 23 5/8" (60 cm) Depth 22 7/16" (57 cm) Weight 127 lbs (57.5 kg) Voltage Connected load see data plate Fuse rating Power consumption when off 0.30 W Power consumption when not off 2.00 W Water pressure (flow pressure) 4.35 - 145 psi Cold or hot water supply max.
Noise measurement General requirements for measuring noise The dishwasher must be loaded with 16 place settings and the Normal program must be used. Installation requirements for measuring noise The dishwasher must be installed as follows:. ^ Install the dishwasher into an appropriate housing unit. ^ Secure the front panel.
Noise measurement ^ Push the insulation mat supplied (depending on model) under the plinth until it is up against the appliance feet a. ^ Attach the toe-kick so that it is flush with the door front b.
Alteration rights reserved / 3/21/2013 M.-Nr. 09 501 400 / 00 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
