Installation Plan

Installationsplan PW 6321 EL
Stand: 15.04.2014 Seite 5
US
CA
Cold water
(Soft water)
Min. flow pressure
14.5 psi
14,5 psi
Max. pressure
145 psi
145 psi
Max. throughput (if hot water supply is not available)
9.25 (21.1) gal/min
35 (80) l/min
On-site connection thread
1" MPT
1" MPT
Length of connection hose (supplied)
59 1/16"
1.500 mm
Water requirements (average 140°F [60°C] program)
Standard connection (with hot water connection)
22.5 gal/h
85 l/h
Additional requirements if hot water supply is not
available.
Hot water
Max. temperature
158 °F
70 °C
Min. flow pressure
14.5 psi
14,5 psi
Max. pressure
145 psi
145 psi
Max. throughput
7.93 gal/min
30 l/min
On-site connection thread
1" MPT
1" MPT
Length of connection hose (supplied)
59 1/16"
1.500 mm
Water requirements (average for 140°F [60°C]
program)
18.5 gal/h
70 l/h
If no hot water supply, connect hose to cold water!
Main water
(Raw water)
(Optional)
Min. flow pressure
14.5 psi
14,5 psi
Max. pressure
145 psi
145 psi
Max. throughput
10.6 gal/min
40 l/min
On-site connection thread
1" MPT
1" MPT
Length of connection hose (supplied)
59 1/16"
1.500 mm
Water requirements (average for 140°F [60°C]
program)
79.3 gal/h
300 l/h
If no raw water supply, connect hose to cold water!
Drainage via
dump valve
Max. temperature
203 °F
95 °C
Machine drain connection (d
a
× s × l)
3" x 1/16" x 4"
75×1,9×100 mm
On-site drain connection (d
i
× s × l)
3" x 1/16" x 2"
75×1,9×50 mm
Max. throughput
52.8 gal/min
200 l/min
Vented drainage required. If ventilation is insufficient,
use with Miele kit, Mat. no. 05238090.
Drain manifolds serving several machines must be of
sufficient cross-section.
Foam vent
A drainage system for foam escaping from the drain
vent can be built using standard drain pipe sections.
A branch with an end cap should be provided for this
purpose.
Fittings
(supplied)
Without base
2 × screws (Diameter × length)
1/2" x 3 9/16"
12 × 90 mm
2 × wall anchors (Diameter × length)
5/8" x 3 9/16"
16 × 90 mm
Machine must be secured!
Fixing materials provided for securing to concrete
floor
Machine data
Width
42 11/16"
1.085 mm
Depth
50 1/16"
1.272 mm
Height
64 9/16"
1.640 mm
Secured dimensions (Width)
43" x 67"
1.090 x 1.700 mm
Recommended clearance to rear wall
(to machine front edge)
70 7/8"
1.800 mm
Net weight
1,430 lbs
648 kg
Dynamic floor load during operation, max.
8,975 N
8.975 N
Static load, max.
7,456 N
7.456 N
Dynamic load max.
1,520 N
1.520 N
Drum frequency, max.
16.7 Hz
16,7 Hz
Average heat dissipation
(depending on room temperature and selected
program)
1,690 W
1.690 W
Installation should only be carried out by authorized installers in accordance with all local and national regulations!
Observe installation instructions when installing machine! All rights reserved!