Operating instructions for heat pump tumble dryer T 8861 WP Edition 111 To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions before it is installed and used for the first time. en - AU, NZ M.-Nr.
Caring for the environment Disposal of the packing material The packing material protects the tumble dryer from transport damage. The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Rather than just throwing these materials away, please ensure they are recycled.
Contents Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Operating the tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Notes on laundry care . . . . . . . . . . . . .
Contents Surfaces of the fluff filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Cleaning without water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Cleaning with water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Refitting the filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Fine filter . . . . . . . . . . . . . .
Contents Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Electronic system lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warning and Safety instructions ~ It is essential to read these instructions. This tumble dryer conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the tumble dryer, please read these instructions carefully before using it for the first time. They contain important information on its safety, installation, use and maintenance.
Warning and Safety instructions ~ The tumble dryer is not suitable for outdoor use. ~ This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they are supervised whilst using it or have been shown how to use it correctly by a person responsible for their safety. ~ This tumble dryer must not be installed and operated in mobile installations (e.g. on a ship).
Warning and Safety instructions Technical safety ~ Before setting up the tumble dryer, check it for any externally visible damage. Do not install or use a damaged tumble dryer. ~ Before connecting the appliance, make sure that the connection data on the data plate (voltage and rated load) match the mains electricity supply. If in doubt, consult a qualified electrician.
Warning and Safety instructions ~ Unauthorised repairs could result in unforeseen dangers for the user, for which Miele cannot accept liability. Repairs should only be undertaken by a Miele approved service technician. ~ Faulty components must only be replaced by genuine Miele spare parts. Only when these parts are fitted can the safety standards of the tumble dryer be guaranteed.
Warning and Safety instructions Correct use , Caution! Risk of fire. To avoid the possible danger of fire, please read these warnings carefully. , A clogged filter is a fire hazard! The fluff filter must be cleaned after every programme. ~ Remove all objects from pockets such as lighters and matches. ~ To prevent the risk of fire, the following textiles must not be dried in this tumble dryer: – Items which have not been washed.
Warning and Safety instructions When washing such heavily soiled items, ensure that you use sufficient detergent and select a high temperature. If in doubt, wash the items several times. ~ Oil-affected items can ignite spontaneously, especially when exposed to heat sources such as in a tumble dryer. The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot escape, the items can become hot enough to catch fire.
Warning and Safety instructions ~ In many programmes, the heating phase is followed by a cooling down phase to ensure that the items are not too hot to handle when you remove them (this also avoids the danger of the laundry self-igniting). The programme is not finished until the cooling down phase is complete. Ensure that you always wait until the end of the programme before removing the laundry. ~ Warning: Do not switch the tumble dryer off before the end of the drying programme.
Warning and Safety instructions ~ The tumble dryer must not be used – without the fluff filters in place or if the fluff filters are damaged. – without the fine filter in place or if the fine filters are damaged. This would cause an excessive build-up of fluff which in turn would cause a fault! ~ After every cycle, remove the fluff from the surfaces and the fluff filters (see "Cleaning and care"). ~ Fluff must not be allowed to accumulate around the tumble dryer.
Warning and Safety instructions ~ Always keep the area around the tumble dryer free of dust and fluff. Dust drawn into the tumble dryer can cause blockages in the condenser unit over time. ~ Do not lean on the door. This can cause the tumble dryer to tip over. ~ Always close the door after use. This way you will avoid the danger of – children climbing onto or into the dryer or hiding things in it. – pets or other small animals climbing into it. ~ The tumble dryer must not be hosed down.
Operating the tumble dryer Control panel a Gentle tumble button For drying items which are not suitable for drying with a great deal of mechanical action. When this option is selected, the drum will rotate less frequently. b Drying level button Indicator lights show the selected drying level. See "How to dry correctly". c Display See the next page. d Delay start button This button is used for: - Delaying the start of a programme. - Selecting Warm air duration.
Operating the tumble dryer The following information appears in the display: – Programme duration – Programme sequence Drying Cooling down Finish The Perfect Dry indicator light remains dark during the following time controlled programmes: Woollens, Warm air, Gentle smoothing. Estimated time remaining – Programmable functions The programmable functions are used to alter the machine's electronics to suit changing requirements. See "Programmable functions" later in this booklet for more details.
Notes on laundry care Care symbols Drying q/r Normal/lower temperature. This dryer is able to dry at lower temperatures in each programme. It is not necessary to divide fabrics q/r. s Do not tumble dry. Ironing I Very hot. H Hot. G Warm. J Do not iron. Tips on drying – See the "Programme chart" for maximum recommended loads for each programme. Overloading can cause unnecessary wear and tear to the laundry, give a disappointing drying result and cause more creasing.
How to dry correctly Brief instructions The headings numbered (A, B, C ...) show the operating sequence and can be used as a brief guide to using your machine. A Sort the laundry Separate the washed laundry and sort it according to . . . . . . the drying level required, . . . the type of fibre or weave, . . . size, . . . the moisture content after spinning. In this way an even drying result will be achieved. ,Make sure that objects, e.g. detergent dispensing balls, have been removed from the laundry.
How to dry correctly D Selecting a programme Tip: You can extend the range of drying levels for some of the programmes (see "Programmable functions"). Woollens, Gentle smoothing, Proofing programmes – These programmes cannot be changed. Selecting Warm air duration ^ Select the programme you want. The relevant indicator light will come on. Indicator lights for drying levels or Extra options and times may also be displayed.
How to dry correctly F Starting the programme The Start/Stop button light will flash when a programme is being selected. The flashing indicates that a programme can be started. ^ Press the Start/Stop button. The Start/Stop button will now light up constantly. Perfect Dry only flashes/illuminates during programmes with drying levels. It remains dark during time controlled programmes (see "Operating the tumble dryer"). Note: The duration shown in the display is only an estimate and can change.
Extra options/Delay start Extra options To begin Delay start The relevant indicator light will come on when selected. ^ Press the Start/Stop button. Gentle tumble For drying items which are not suitable for drying with a great deal of mechanical action. When this option is selected, the drum will rotate less frequently. The programme duration will be extended. If in doubt, reduce the size of the load. Buzzer A buzzer sounds (at intervals for a maximum of 1 hr) to let you know the programme has finished.
Programme chart Extra options Gentle tumble Able to be selected with the following programmes: Cottons, Minimum iron, Shirts, Denim, Warm air. Buzzer Able to be selected with all programmes. Programmes Cottons Max. load: 8 kg* Extra dry, Normal** Fabric type Single and multi-layered cotton fabrics such as towelling, jerseywear, T-shirts, underwear. Notes – Select Extra dry for multi-layered and very thick fabrics. – Do not use Extra dry for loopknit fabrics (e.g.
Programme chart Woollens Max. load: 2 kg* Fabric type Fabrics containing wool blends. Notes – Woollen garments are fluffed up. – Remove garments immediately at the end of the programme. Outerwear Max. load: 2.5 kg* Normal, Hand iron Fabric type Outerwear which is suitable for drying in a tumble dryer. Proofing Max.
Programme chart Hygiene Max. load: 3.5 kg* Fabric type Cottons and linen fabrics, which will be in direct contact with the skin, e.g. underwear, nappies, towelling, bed linen, pillow and mattress covers. Note The temperature is held constant for a longer period of time to deactivate micro-organisms, e.g. germs or house dustmites, and also to reduce the number of allergens in the laundry. This programme should not be interrupted as this would prevent the micro-organisms from being deactivated.
Changing the programme sequence You cannot change to another programme once a programme has started (this prevents unintentional alterations). You will need to cancel the current programme before you can select a new one. Once a programme has started - Cancelling the programme and then selecting a different programme ^ Press the Start/Stop button. The items will be cooled down, depending on the temperature reached and how long they have been dried for. Changing Delay start ^ See "Delay start".
Cleaning and care Emptying the condensed water container Condensate is collected in the condensed water container during drying. Empty the condensed water container after every drying programme, unless the dryer has been connected for external drainage (see "Installation"). If the condensed water container is full, – the programme will be cancelled. – the Empty the container indicator light comes on. The indicator light will go out when the door is opened and closed again.
Cleaning and care Adhering to cleaning intervals This tumble dryer has a multistage filter system, consisting of the fluff filters in the door and the door opening and an additional fine filter. This system requires maintenance. – This tumble dryer must not be used without the fluff filters and fine filter in place. The grille at the bottom right of the appliance must also always be in place. – Also ensure that the fluff filters and the fine filter are not damaged.
Cleaning and care Surfaces of the fluff filters Cleaning intervals Clean the surfaces of the fluff filters in the door and the door opening after each drying programme. Cleaning without water Tip: You can use a vacuum cleaner to remove the fluff. ^ Use your fingers or a vacuum cleaner to remove the fluff from the surface of the filter. 1 Fluff filter 2 Seal ^ Open the door and pull the fluff filter (1) out of the door as illustrated.
Cleaning and care Cleaning with water If there is a great deal of compacted fluff on any of the filters, they must be removed and cleaned under hot running water. ^ Open the door and pull the fluff filter out of the door as described previously. The two filters in the door opening can also be removed if you need to clean them with water. Refitting the filters ,The fluff filters must be dry before they are refitted. Damp or wet filters could cause operational faults.
Cleaning and care Fine filter Cleaning intervals Only clean the fine filter if the Clean the filters indicator light comes on. To switch off the Clean the filters indicator light: ^ Remove, clean and refit the fine filter while the dryer is switched on. ^ Pull the fine filter out by the handle. Removing the fine filter At the bottom left of the appliance: ^ Pull the handle out of the fine filter. ^ Press the cover panel for the fine filter. The panel will open.
Cleaning and care Cleaning the fine filter cover panel Cleaning the heat exchanger unit compartment ,Danger of injury! Do not touch the cooling fins as they are very sharp and may cut your fingers. ,Risk of damage! ^ Remove any fluff with a damp cloth (e.g. Original Miele all purpose microfibre cloth, available at www.miele-shop.com, depending on country). Be careful not to damage the rubber seal. Carefully run the dusting brush of the vacuum cleaner across the cooling fins.
Cleaning and care Replacing the fine filter Only when the filter is fitted correctly and the cover panel is closed can the condensed water system be sealed and the correct functioning of the tumble dryer be guaranteed. Cleaning the tumble dryer Disconnect the machine from the mains electricity supply. ^ Insert the handle into the fine filter.
Problem solving guide Problem solving guide With the help of the following notes, minor faults in the performance of the machine, some of which may result from incorrect operation, can be put right without contacting Miele. A call-out charge will be applied to unnecessary service visits where the problem could have been rectified as described in these Operating instructions.
Problem solving guide Problem Possible cause Remedy This is a reminder to – Clean the fine filter. clean the fine filter in front – See chapter "Cleaning and of the heat exchanger unit care". under running water. – The indicator light goes out once the fine filter has been removed and refitted while the dryer is switched on. The fine filter is not in ~F~ lights up and a – Correctly fit the fine filter: ~F~ will go out. programme cannot place or has been be started. incorrectly fitted.
Problem solving guide An unsatisfactory drying result Problem Possible cause Remedy The laundry is not sufficiently dry. The load consisted of different fabrics. – Final drying cycle with Warm air. – Select a different programme next time. Tip: You can alter the drying See "Programmable functions". levels for some programmes. Garments or downfilled pillows develop an unpleasant odour due to tumble drying. – Not enough laundry detergent was used during washing.
Problem solving guide Other problems Problem The drying process goes on too long or even switches off. Possible cause Remedy * Ventilation to and from the dryer may be insufficient (e.g. because it is installed in a small room). This has caused the temperature in the room to rise sharply. Open a door or window while the machine is in operation for increased air flow. – Detergent residue, hair and fine fluff may have blocked the fluff filters and fine filter. – The cooling fins may be blocked.
Problem solving guide Problem Possible cause There are humming noises. The compressor is operating. A programme cannot be started. Power cut. The interior drum lighting is not switched on. Remedy None. These noises are quite normal and do not indicate a fault. There is no immediate – Is the tumble dryer cause. switched on? – Is the mains plug plugged in? – Is the door closed properly? – Has the fuse or circuit breaker tripped? – If you cannot remedy the problem, there is a fault. Call Miele.
Problem solving guide Cleaning the cooling fins (Grille at bottom right) ,Generally, the cooling fins do not need to be cleaned. They should only be cleaned if excessive quantities of dust and lint are causing unusually long drying times. ,To avoid damaging the cooling fins, run the vacuum cleaner (using dusting brush or crevice nozzle) lightly across them without pressure. Use the yellow opener supplied to open the grille at the bottom right of the front of the tumble dryer.
Problem solving guide Changing the lamp Disconnect the machine from the mains electricity supply. The lamp specification and maximum wattage are stated on the data plate and on the lamp cover. ^ Open the door. ^ Replace the lamp. You will find the interior lamp cover at the top of the drum aperture. ^ To close the cover, push it upwards and press it on the left and right until you hear it click into position.
After Sales service In the event of any faults which you cannot remedy yourself, please contact – Miele (see back cover for address). When contacting Miele, please quote the model and serial numbers, both of which are located on the data plate situated on the right-hand side below the drum aperture.
Installation and connection Front view a Mains connection cable f Four height adjustable screw feet b Control panel g Cool air intake panel (do not block, e.g.
Installation and connection Rear view ,If transporting the dryer at an angle, only tip towards the left side. a Protruding lid for holding when moving the machine (see arrows) b Mains connection cable c Hose for external drainage of condensed water d Accessories for connection to a sink drain outlet Transporting the dryer When moving the dryer, hold it by the lid where it protrudes to the rear.
Installation and connection Installation site ,The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted. ,The cool air intake panel at the front of the dryer must not be blocked or covered, e.g. by a laundry basket, as this would cause a fault.
Installation and connection With niche heights of: – 830-840 mm, longer screw feet* are required. ^ The screw feet can be adjusted to compensate for any unevenness in the floor. – 870-885 mm / 915-930 mm, one or two raising kits* are required. ,The gap between the tumble * accessory available to order N.B. If you wish to push the tumble dryer under a worktop and there is space to do this without removing the lid, the building-under kit is not necessary. Otherwise the building-under kit is essential.
Installation and connection External condensed water outlet General notes When drying is in progress, condensed water is pumped into the condensed water container through the drain hose at the back of the dryer. The condensed water can also be drained off directly if the machine is installed near a sink, drain outlet etc. so that the condensed water container does not have to be emptied. Drain hose length . . . . . . . . . . . . 1.50 m Maximum delivery head . . . . . . . 1.50 m Maximum drain hose length . .
Installation and connection External drainage via a sink or gully ^ See "Front view" illustration. ,If you want to drain the water off into a sink, you will need to secure the hose carefully, e.g. by tying it to a tap to make sure it cannot slip during use. Otherwise there is a risk of overflowing water which could cause damage. Example: Connection to a sink drain outlet The drain hose with non-return valve fitted can be connected directly to a suitable sink drain outlet.
Installation and connection ^ Fit adapter 1 to the sink drain outlet using nut 2. If this nut has a flat disc in it, you should take the disc out first. ^ Attach the end of the hose 4 to adapter 1. ^ Use a screwdriver to tighten hose clip 3 up close to the nut. 1 Adapter 2 Nut 3 Hose clip 4 End of the hose 5 Non-return valve 6 Tumble dryer drain hose ,Non-return valve 5 has to be fitted with the arrow pointing in the direction of flow (i.e. towards the sink).
Installation and connection Electrical connection Important This tumble dryer is supplied ready for connection to an AC single phase supply. The machine is supplied with a mains cable with moulded plug. The wires in the mains lead are coloured in accordance with the following code: The accesibility of the plug must be always ensured in order to separate the dryer from the mains.
Consumption data Load1 Final spin speed in Residual a domestic washing moisture machine Energy Duration kg rpm % kWh min. Cottons Normal2 8.0 1000 60 2.10 137 Cottons Normal 8.0 8.0 8.0 8.0 1200 1400 1600 1800 53 50 44 43 1.90 1.80 1.60 1.55 124 118 105 103 Cottons Normal + Gentle tumble 8.0 1000 60 2.15 140 Cottons Hand ironrr2 8.0 1000 60 1.55 99 Cottons Hand ironrr 8.0 8.0 8.0 8.0 1200 1400 1600 1800 53 50 44 43 1.35 1.25 1.10 1.
Technical data Height 850 mm Width 595 mm Depth Depth with door open 596 mm 1071 mm Height for building under Width for building under 820 mm 600 mm Depth for building under Suitable for pushing under a worktop 600 mm Yes Suitable for stacking Weight Yes 61 kg Drum volume Maximum capacity 111 l 1-8 kg dry weight Capacity of condensed water container Drain hose length approx. 4.2 l Maximum delivery head Maximum drain hose length 1.5 m 4m Length of connection cable 2m 1.
Electronic system lock and Programmable functions for changing standard settings This tumble dryer is programmed at the factory so that is operates effectively for all requirements. However, you do have the ability to change the standard settings. You can adapt the electronics of the tumble dryer to suit your personal needs. The features "Electronic system lock" and "Programmable functions" are at your disposal, but do not have to be utilised.
Electronic system lock The system lock prevents your machine being used without your knowledge. You can switch on the system lock if required. The dryer's electronics are then locked. The dryer can still be switched on but a programme cannot be started. – If an attempt is made to start a programme, the indicator light for the Gentle tumble button will come on and the key symbol 0-§ will appear in the display.
Programmable functions Extending the range of the drying level for the "Cottons" programme The electronics of this dryer ensure a very effective and energy-efficient drying process. You can, however, extend the range of the drying level in this programme so that there is more or less moisture in the laundry at the end of the programme. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off. – The door is closed.
Programmable functions Extending the drying level for the "Minimum iron" programme The electronics of this dryer ensure a very effective and energy-efficient drying process. You can, however, extend the range of the drying level in this programme so that there is more or less moisture in the laundry at the end of the programme. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off. – The door is closed.
Programmable functions Altering the Anti-crease function Helps prevent creasing if laundry is not normally removed immediately after the end of a programme. Anti-crease – is set at the factory, can be shortened or switched off completely. – can be used for all programmes, except Woollens. – should always be switched on. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off. – The door is closed.
Programmable functions Altering the volume of the buzzer The buzzer has two volumes. The option selected will be displayed by a number which will alternate with P. Follow steps (A,B,C ...) to programme and store in memory. 0 Factory default setting; Normal buzzer Before you begin, first ensure that: I Loud buzzer (The Automatic plus indicator light will also flash) – The dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C.
Programmable functions Extending the drying level for the "Automatic plus" programme The electronics of this dryer ensure a very effective and energy-efficient drying process. You can, however, extend the range of the drying level in this programme so that there is more or less moisture in the laundry at the end of the programme. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off. – The door is closed.
Programmable functions Setting Standby To save energy, the display goes out after 10 minutes and the indicator light for the Start/Stop button will start flashing slowly. Factory default; Not in current programme As described under "On". But: The display and indicator lights will not switch off during a programme. Reactivating from Standby Off ^ Turning the programme selector or pressing one of the buttons switches the display back on again. This will not alter a running programme.
Programmable functions Before you begin, first ensure that: – The dryer is switched off. – The door is closed. A Press the Start/Stop button and keep it pressed in whilst carrying out steps B-C. B Switch the dryer on. Wait until the indicator light for the Start/Stop button lights up constantly. . . C . . . and then release the Start/Stop button. D Press the Gentle tumble button five times. – The Gentle tumble indicator light will briefly flash eight times.
Programmable functions Memory function The electronics will memorise any Extra options selected for a programme. The duration selected for the timed drying programmes will also be stored in memory. These settings will be selected automatically the next time the programme is chosen. You can either accept these or change them by pressing the appropriate button. Follow steps (A,B,C ...) to programme and store in memory. Before you begin, first ensure that: – The dryer is switched off. – The door is closed.
Programmable functions Keypad tone An audible tone sounds each time a button is pressed. The option selected will be displayed by a number which will alternate with P. Follow steps (A,B,C ...) to programme and store in memory. 0 Factory default setting; Keypad tone deactivated Before you begin, first ensure that: I Keypad tone activated (The Automatic plus indicator light will also flash) – The dryer is switched off. – The door is closed.
Programmable functions Adjusting the dryer's electronics for very soft water ,Extremely soft water can affect the sensitivity of the control electronics. Important If the dryer is installed in an area with very soft water, you should contact your local water supplier for information and advice regarding water hardness and water conductivity. If the water conductivity is less than 150 µS, the following programmable function will need to be activated.
Programmable functions Extending the drying level range You can extend the range of the drying levels for many of the programmes: Machine iron + (drier than Machine iron). Light dry (dryer than Hand iron). Normal+ (dryer than Normal). You can use this programming function only for programmes which allow you to select the drying levels. Follow steps (A,B,C ...) to programme and store in memory. The option selected will be displayed by a number which will alternate with P.
Alteration rights reserved/0313 M.-Nr.
