Operating instructions Cordless stick vacuum cleaner en-GB HS19 M.-Nr.
Contents Warning and Safety instructions...................................................................... 4 Caring for the environment .............................................................................. 11 Guide to the appliance ...................................................................................... Installation and connection .............................................................................. Assembling the vacuum cleaner .........................................
Contents Service................................................................................................................ Contact in case of malfunction ........................................................................... Warranty .............................................................................................................. Warranty in the UAE ............................................................................................ 34 34 34 34 Optional accessories ........
Warning and Safety instructions This vacuum cleaner conforms to current safety requirements. Inappropriate use can lead to personal injury and damage to property. Please read the operating instructions before using the vacuum cleaner and charging the battery for the first time. They contain important information on the safety, use and maintenance of the vacuum cleaner. This will prevent both personal injury and damage to the appliance.
Warning and Safety instructions The vacuum cleaner must only be used to vacuum dry floor surfaces. Do not vacuum people or animals. Any other types of use, modifications or alterations are not permitted. This vacuum cleaner can only be used by people with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, if they are supervised whilst using it or have been shown how to use it in a safe way and understand and recognise the consequences of incorrect operation.
Warning and Safety instructions Technical safety The vacuum cleaner operates at 25.2 V. It is classified as a class III appliance. This appliance is supplied by a safety extra-low voltage (SELV) power source where the voltage is low enough to protect users from the risk of electrical shock. A Class II charger is used for supplying power to charge the vacuum cleaner. Before using the vacuum cleaner and its accessories, check for any visible signs of damage. Do not use a damaged appliance.
Warning and Safety instructions Miele can only guarantee the safety of the appliance when genuine Miele replacement parts are used. Faulty components must only be replaced with genuine Miele replacement parts. Cleaning Do not immerse the vacuum cleaner or any accessories supplied with it in water. The Electrobrush/handheld brush (depending on the model), the PowerUnit, the suction tube, the body and the Comfort handle contain electrical wires.
Warning and Safety instructions Do not vacuum up any inflammable or combustible liquids or gases and do not vacuum in areas where such substances are stored. Never touch the Electrobrush/handheld brush (varies according to the model) while it is rotating. Do not use the Electrobrush/handheld brush (varies according to the model) at head height. Do not vacuum at head height and do not let the suction get anywhere near a person's head.
Warning and Safety instructions Technical safety The AP01 battery, the LG01 charger and the LS03 charger cradle are designed for use with the Miele HS19 vacuum cleaner. For safety reasons, the vacuum cleaner must not be used with a battery, charger or charger cradle produced by another manufacturer. Only the LG01/xx charger or the LS03/xx charger cradle supplied with the vacuum cleaner can be used to charge the AP01 battery.
Warning and Safety instructions Stop using the AP01 battery immediately if you notice an unusual smell from it, if liquid is leaking from it, if it is significantly overheating or if it is discoloured or deformed. Dispose of the AP01 battery immediately (see safety notice “Disposing of the AP01 battery” at the end of this chapter as well as “Caring for the environment” – “Disposing of old batteries”). Batteries will deplete over time. They can then leak corrosive fluids.
Caring for the environment Disposal of the packing material The packaging is designed to protect the appliance from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Recycling the packaging reduces the use of raw materials in the manufacturing process and also reduces the amount of waste in landfill sites.
Guide to the appliance 12
Guide to the appliance a Comfort handle b Release catch for Comfort handle (on the back) c Dust container handle d Dust container with pre-filter, fine dust filter and motor protection filter e PowerUnit with battery connection and connections for Comfort handle, suction tube, Electrobrush and dust container f Release catches for battery (on both sides of the battery) g Charging socket (at the bottom of the battery) h AP01 lithium-ion battery i Connector j Multi Floor XXL Electrobrush (some models feature B
Installation and connection Assembling the vacuum cleaner You can assemble the vacuum cleaner in 2 different ways.
Connecting the Comfort handle Depending on how your vacuum cleaner is configured, you can connect the Comfort handle to either the suction tube or the PowerUnit. Press the release catch and remove the Comfort handle by pulling upwards. Connecting the PowerUnit and the suction tube Push the Comfort handle down on to the suction tube connector from above until it audibly clicks into place (left image detail).
Push the PowerUnit connector down on to the suction tube from above until it audibly clicks into place (right image detail). Push the battery along the guide lines until it audibly clicks into place in the PowerUnit. Press the release catch to separate the individual sections from each other. Inserting the battery If you want to separate the sections again, press both release catches at the side of the battery to remove the battery. Remove the protective sticker from the battery.
Connecting the Electrobrush General battery information Depending on how your vacuum cleaner is configured, you can connect either the PowerUnit connector or the suction tube connector to the Electrobrush. The rechargeable battery is supplied not fully charged. Charge the battery completely before using it for the first time. Allow approximately 4 hours for this. It is essential to charge the battery for the first time in the PowerUnit in order to activate maximum power in the battery.
Charging the battery (without wall mounting) Charging the battery (with wall mounting) You can store the vacuum cleaner upright and charge the battery directly. There are 2 ways to store and charge the vacuum cleaner in the supplied wall bracket. You will need a suitable location near a free power socket for mounting the appliance on the wall. Connect the PowerUnit to the Electrobrush to provide a secure base for the vacuum cleaner.
Wall mounting The supplied wall bracket has a mounting plate with a bag of screws attached to the back. Attach the mounting plate to the point on the wall where you want the wall mounting to be. Remove the bag of screws. Press the release catch at the bottom of the wall bracket. Remove the mounting plate from the wall bracket by sliding it downwards.
Attaching the mounting plate 2 plugs and 2 T20 TORX screws are supplied for attaching the mounting plate to the wall. You will also need a battery-operated screwdriver or a drill (with a drilling diameter of 6 mm). Depending on how your vacuum cleaner is configured, select a distance of 45 cm or 98 cm between the bottom edge of the mounting plate and the floor. Attach the mounting plate to the wall.
Connecting the wall bracket The charging process will start. Battery charging state indicator (while charging) The battery charging state is displayed on the PowerUnit. Slide the wall bracket down into the mounting plate from above until it audibly clicks into place. Slide the PowerUnit of the fully assembled vacuum cleaner, with the battery inserted, down into the wall bracket from above. Plug the supplied charging cable into the charging socket on the bottom of the battery.
If the battery has not been used for a long time and has run down, it will go into a safe mode. As a result, the battery charging state indicator will only respond after approximately 30– 60 minutes when charging in the PowerUnit. Using the accessories supplied Battery charging state indicator (while in use) The battery charging state is displayed on the PowerUnit. Charging capacity Display Approx.
Electrobrush Multi Floor XXL (SEB 430 or SEB 435) Follow the flooring manufacturer’s cleaning and care instructions. The Electrobrush can be used for all normal cleaning of carpets, rugs and hard flooring which is not susceptible to scratching. Tip: The suction tube is not a convenient option for cleaning carpeted stairs. Miele offers a range of suitable accessories for many special applications (see “Optional accessories”).
Use Switching on and off Pull the plug out of the charging socket on the battery. If you have put the vacuum cleaner away in the the wall bracket for storage, take it out. After the battery has been fully charged once in the PowerUnit, the charger cradle can be used to charge it. Push the battery into the charger cradle until it audibly clicks into place. Insert the plug into a power socket. The charging process will start. The battery charging state indicator flashes on the left.
The floor covering detection function is activated in the medium and highest power levels. The Electrobrush power output is automatically set to the optimum level based on the type of flooring – this can lead to a change in the operating noise. Illuminating the work area (depending on model) The Electrobrush on your vacuum cleaner is equipped with BrilliantLight to illuminate the work area.
Lift the dust container upwards to remove it. The contents of the container can be disposed of with normal domestic waste, providing they consist of general household dust only. Hold the dust container close to the bin to prevent dust from billowing out. Turn the lid of the dust container in the direction of the arrow as far as the next stop. 26 The cover at the bottom of the dust container will open and the dust will fall out. Turn the lid of the dust container back to its original position.
Cleaning the fine dust filter The fine dust filter is located in the dust container. Clean the fine dust filter at least once a month. Remove the dust container. Once it is clean, replace the fine dust filter in its position in the dust container. Replace the dust container on the PowerUnit connector. Cleaning the pre-filter The pre-filter is located in the dust container. Clean the pre-filter when required. Remove the dust container. Remove the fine dust filter.
Unlock the motor protection filter by turning it anti-clockwise and lift it upwards to remove it. Replace the pre-filter in the dust container. Risk of damage caused by incorrect cleaning. The pre-filter can become damaged and be less effective as a result. Do not use pointed or sharp-edged objects to clean the filter. Carefully knock the dust out of the pre-filter over a bin. Tip: Use a tool like a fine cleaning brush to clean the inside of the pre-filter thoroughly.
Cleaning the dust container Removing threads and hairs Clean the dust container as required. Place the Electrobrush/handheld brush upside down on a level, clean surface. Remove the dust container. Empty the dust container over a bin and lift the pre-filter upwards to remove it. Clean the dust container using water and mild washing-up liquid. Dry the dust container thoroughly. Replace the pre-filter in the dust container. Replace the dust container on the PowerUnit connector.
Removing the roller brush Replacing the rechargeable battery (Not possible with the handheld brush) An original Miele AP01 lithium-ion rechargeable battery (HX LA) is required. You can take the roller brush out of the Electrobrush in order to remove stubborn soiling and clean the inside of the Electrobrush. Unlock the cover on the side of the Electrobrush so that the symbol becomes visible. Lift the cover up as far as it will go. Remove the roller brush.
Problem solving guide Many malfunctions and faults that can occur in daily operation can be easily remedied. Time and money will be saved because a service call will not be needed. The following guide may help you to find the reason for a malfunction or a fault, and to correct it. Risk of injury caused by rotating roller brush. You can injure yourself on the rotating roller brush. Switch the vacuum cleaner off before dealing with any problems. Use the On/ Off switch on the Comfort handle to do this.
Problem Cause and remedy The vacuum cleaner There is no battery inserted or the battery is inserted does not start when it is incorrectly. switched on. Insert the battery or check how the battery is positioned (see “Installation and connection” – “Inserting the battery”). The rechargeable battery is not sufficiently charged. Charge the battery exactly as described in these operating instructions (see “Installation and connection” – “Charging the battery”).
Error messages Risk of injury caused by rotating roller brush. You can injure yourself on the rotating roller brush. Switch the vacuum cleaner off before dealing with any problems. Use the On/ Off switch on the Comfort handle to do this. Error messages are displayed with a quick flashing light on the battery charging state indicator on the PowerUnit. Problem Cause and remedy Bottom light flashes quickly Internal system error Remove the battery, wait for 10 seconds, reinsert it and charge it.
Cleaning and care Service Risk of injury caused by rotating Contact in case of malfunction roller brush. You can injure yourself on the rotating roller brush. Switch the vacuum cleaner off before cleaning it. Use the On/Off switch on the Comfort handle to do this. In the event of any faults which you cannot remedy yourself, please contact your Miele Dealer or Miele Service. Vacuum cleaner and accessories Risk of electric shock from mains voltage.
Optional accessories Follow the flooring manufacturer’s cleaning and care instructions. We recommend using only genuine Miele accessories bearing the “ORIGINAL Miele” logo on the packaging. Only these will guarantee the optimum performance of your vacuum cleaner and the best possible cleaning results. Please note that faults and damage caused by use of accessories which do not bear the “ORIGINAL Miele” logo on the packaging are not covered by the vacuum cleaner warranty.
Electrical connection for the UK All electrical work should be carried out by a suitably qualified and competent person in strict accordance with current national and local safety regulations (BS 7671 in the UK). The voltage and frequency are given on the data plate located underneath the vacuum cleaner. Please ensure that these match the household mains supply. The fuse rating is quoted on the plug. The appliance is supplied with a cable and moulded plug ready for connection to a 230-240 V/50 Hz a.c.
United Kingdom Miele Co. Ltd., Fairacres, Marcham Road, Abingdon, Oxon, OX14 1TW Tel: 0330 160 6600, Internet: www.miele.co.uk/service, E-mail: info@miele.co.uk Australia Miele Australia Pty. Ltd. ACN 005 635 398 ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield, VIC 3180 Tel: 1300 464 353 Internet: www.miele.com.au China Mainland Miele Electrical Appliances Co., Ltd. 1-3 Floor, No. 82 Shi Men Yi Road Jing' an District 200040 Shanghai, PRC Tel: +86 21 6157 3500 Fax: +86 21 6157 3511 E-mail: info@miele.
