Operating instructions Washer-Extractor WS 5243 WS 5323 It is essential to read these operating instructions before installing, commissioning or using the machine, to avoid the risk of accident or damage to the machine. Q M.-Nr.
M.-Nr.
Contents Indice Page Warning and Safety instructions . . . . . . . Caring for the environment . . . . . . . . . . Guide to the machine . . . . . . . . . . . . . Control panel . . . . . . . . . . . . . . . . . . Guide to the controls . . . . . . . . . . . . . . Operation . . . . . . . . . . . . . . . . . . . . Setting the local language . . . . . . . . . . . Setting the current time of day and date . . . . Commissioning . . . . . . . . . . . . . . . . Open the drum . . . . . . . . . . . . . . . . .
Warning and Safety instructions Where there is any damage to the machine or to the cable insulation the machine must not be used until it has been repaired. Read the operating instructions through before using this machine for the first time. This way you will avoid the risk of accidents or damage to the machine. Appropriate use of the machine Any removable outer panels must be in place, and all moving or electrical parts shielded before the machine is operated.
Warning and Safety instructions Remember that the door porthole glass can become hot during the operation of the machine. Do not let children touch it . in the situation specified by the manufacturer in order to avoid the danger of adverse chemical reactions and material damage. If in doubt check the suitability of the product for use in this machine with the manufacturer before using it. Always make sure the drum is stationary before reaching in to remove washing.
Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags etc. are disposed of safely and kept out of the reach of babies and young children. Danger of suffocation! Rather than just throwing these materials away, please ensure they are offered for recycling.
Guide to the machine Overflow Emergency stop switch Control panel Detergent dispenser drawer Door "Unclean side" Service panel WS 5243/5323 "Unclean side" Emergency stop switch Control panel Overflow Door "Clean side" Service panel WS 5243/5323 "Clean side" 7 M.-Nr.
Guide to the machine Control panel "Clean side" (loading side) Key switch Mains on Y switch Mains off Z switch Door 5 button Display Block plus Tbutton Starch stop U button Spin stop V button Programme selector Cursor 1 2 buttons Plus 4 Minus 3 buttons Delay start W button Start X button End 7 button 9 Optical interface Control panel "Clean side" (Side for unloading disinfected laundry) Printer socket Display A printer can be connected to the machine for printing out programme reports. M.-Nr.
Guide to the machine 1 Mains on Y switch 2 3 Keys for the key switch Key 1 (2 supplied) for operating levels A and B. Mains off Z switch Door 5 button Key 2 for operating levels A, B, C. Key switch Position A – Free access At this operating level only those programmes can be started which have been allocated free access. See Programming Instructions for allocation of free access. Key 3 for operating levels A, B, C, D.
Guide to the machine Block+ T button with indicator light When the button is pressed the light above it comes on. The corresponding programme block (e.g. Pre-wash) is added to the programme. Pressing on the button a second time de-selects the function. Programme selector switch Programme numbers 1 - 24 can be selected directly. Programme numbers 25 99 can be selected using selector position 24 together with the "Plus 4 " button.
Guide to the machine Delay start W button If this button is pressed before the start of a programme, the display indicates that a start time should be selected. If the button is pressed again the Delay start option is cancelled. If this button is pressed after the start of a programme the current time of day and date are shown. Start X button Press to start the selected programme. End 7 button Pressing on this button halts a programme (Stop mode).
Operation Setting current time and date * Setting the local language* (if necessary) Switch the machine off with the Mains off Z switch. To set the local language the programming mode must be accessed by pressing simultaneously on the "Mains on” switch and the “Start” button. Normally German and one other language are available. Turn the key switch to position B.
Operation Open the drum: The washer-extractor must be commissioned by an approved Customer Service technician or authorised Service Dealer. COMMISSIONING Open the on-site water stopcocks, (and the supply valves for steam, if relevant for the version of the machine). Switch on the electricity supply at the mains (on site). Turn the key switch to position B (Operation). The functions described below refer only to Operating level B. Press the Mains on Y switch.
Operation If any fluff has built up around the drum door it must be removed. The locking mechanism must also be checked on a regular basis to ensure that it is working correctly. First bring down the half with the safety lock and then bring down the other half making sure the locking mechanism visibly engages and is secure. Pull the machine door downwards and with both hands use even pressure to lock the door. Do not slam the door down to shut it.
Operation Load weight (dry laundry) WS 5243 WS 5323 max. 24 kg max. 32 kg Load weights for individual programmes are quoted in the Programme Survey. Liquid detergent must not be filled higher than the level marker, as otherwise it will get through the siphon and into the detergent dispenser drawer before it is needed.
Selecting a disinfection programme Disinfection programmes are locked. The wash temperature cannot be changed. Disinfection programmes are locked 1 minute after a programme has started. They cannot then be interrupted, stopped or shortened. The programme sequence is shown in the display after the start of the programme. 60°C 95°C à The door on the “Clean side” cannot be opened until a programme has finished and disinfection has been sucessfully achieved.
Unloading the machine Open the door on the “Clean side” (unloading side) at the end of a programme If this was the last wash load of the day, or for a longer period: At the end of the Programme, with a stationary drum and no more water in the machine the following display is shown (for example): Close the drum. To ensure that the drum door is correctly closed the arrow on the safety lock must be completely visible.
Selecting an “unlocked” programme Turn the key switch to position B "Operation". Position the cursor on the input field for the spin speed and set the required spin speed with the Plus 4 or Minus 3 buttons. Press the Mains on Y switch. Press Start X in to start the programme. Turn the programme selector switch to the required programme. Once the programme has started the programme sequence will show in the display.
Selecting an “unlocked” programme Open the door on the “Unclean side” (loading side) at the end of a programme If this was the last wash load of the day, or for a longer period: At the end of the Programme the door on the “Unclean side” can be released. If there is no more water in the machine and the drum is stationary the following display is shown (for example): Leave the drum door open. Switch off the machine by pressing the Mains off Z switch.
Additional functions With Pre-wash Without spin A pre-wash can be selected for heavily soiled laundry. Without spin can be selected before starting a programme by pressing the Without spin V button. The indicator light above the button lights up. The pre-wash programme block can be selected before starting a programme by pressing the Block + T button. The indicator light above the button lights up. PROGRAMME 25 COTTONS Rinse 3 WITHOUT SPIN Press the without spin or end button.
Additional functions Programme interruption Here the Display shows the following: To stop a programme press the End 7 button. To continue the programme again press the Start X button. PROGRAMME 1 TH-Disinfection Start time >14< : 30 hrs After the start time has been set press the Start button. Programme cancellation The current time of day is always displayed first. The cursor points to the input field for "hours". Should you wish to cancel a programme, press the End 7 button twice in succession.
Notes Locked programmes (Disinfecting programmes) Rinsing with hot water Rinsing with hot water is a benefit for machines connected to a hot water supply. If a disinfection programme is interrupted or if there is a fault during the disinfecting phase (wash time 2), the whole programme must be repeated to ensure that disinfection is achieved. Standard programmes 1 Cottons 95°C and 2 Cottons 60°C are programmed to rinse with hot water.
Liquid dispensing Dispenser pump Suction pipe Amount to be dispensed Follow the detergent manufacturer’s guidelines. Always follow the instructions of the chemical manufacturer when using cleaning agents and special application chemicals. Only use such chemicals for the purpose and in the situation specified by the manufacturer in order to avoid the danger of adverse chemical reactions and material damage.
Liquid dispensing Commissioning the dispensing pumps SERVICE - OPERATION SERVICE PROGS SERVICE PROGRAMME 2 Dispenser valve >D1< Disp. time 20 Secs. Cancel with the End button. Before the liquid dispensing pumps can be used the liquid detergent must be drawn into the system and the amount to be dispensed set. The Service Programme is used for this. Cancel with the End 7 button. Repeat the whole process with D2 and D3.
Problem solving guide Power cut during a wash programme With an extended power cut: With a short power cut: The programme remains in the last position, and when power is restored the following message appears in the Display: Switch off the machine. Switch off the electricity supply at the mains switch (isolator). PROGRAMME 25 COTTONS PROGRAMME STOP THROUGH POWER CUT Please press the Start button. Turn off the stopcocks and valves on site for water or steam.
Problem solving guide Fault messages PROGRAMME 25 COTTONS PROGRAMME STOP HEATING SYSTEM FAULT Short circuit on heater sensor 1. Repairs to machines operating with electricity or steam should only be undertaken by a suitably qualified service engineer to ensure safety. Unauthorised repairs could be dangerous. Call the Service Department. PROGRAMME 25 COTTONS PROGRAMME STOP HEATING SYSTEM FAULT Cut-out of heating sensor 1.
Problem solving guide Possible reasons for increased levels of foaming: PROGRAMME 25 COTTONS PROGRAMME STOP IMBALANCE SWITCH Press the On-Off switch. – detergent type Press the Mains off Z and the Mains on Y switches. Only use detergent formulated for use in commercial washer extractors. Domestic laundry detergent is not suitable.
After sales service Should a fault occur please contact the Service Dept. When contacting the Service Dept, please quote the model type and machine number (Fabr.-Nr.), and part number (M.-Nr.). These can be found on the data plate : at the top of the door on the "Unclean side" or: on the side casing of the machine above the ventilation grille. Only use genuine Miele spare parts. When ordering spare parts the Spare Parts Dept will also need to know the model type and machine number (Fabr.-Nr.
Cleaning and Care The machine should be cleaned, wherever possible, immediately after use. Check the drum door regularly for a build up of fluff and clean as necessary. Check the door locking mechanism regularly to ensure it is working correctly. On no account use high pressure cleaners or hose down the machine. The drum is made of non-rusting stainless steel. However water with a high iron content or foreign bodies in the wash, (e.g.
Cleaning and Care Greasing After about 1000 running hours apply Arcanol L 100 to both grease nipples of the drum. When not in use for a longer period of time: If the machine is not going to be used for a longer period of time (4 weeks or more) the drum bearings should be lubricated and the drum rotated several times after the last use. See the "Cleaning and Care" section of the Operating Instruction manual supplied with the machine.
Explanation of the symbols on the data plate Noise level Registered on the “A” scale During wash During spin WS 5243 60.7 dB 81.6 dB WS 5323 63.5 dB 80.1 dB 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 Machine type Machine number / year of manufacture* Voltage / Frequency Measured in Germany in accordance with Control fusing DIN (IEC) 45 635 machine noise regulations Drive motor 3. GSGV § 1 1.
Installation This machine is for use only with articles which have not been treated with dangerous or inflammable substances. To avoid the possibility of frost damage on no account install the machine in a room which is exposed to frost. Transit fittings 2 at the rear are each secured with 3 hex screws (SW 17) and must only be removed once the machine has been installed in its final position. Ensure they are removed before commissioning. To remove them detach the lower sides from the machine.
Installation Plumbing Water connection Australia Connection to the water supply must be carried out by a suitably qualified and competent person in accordance with local and national water and safety regulations (DVGW in Germany) via a stopcock, (DIN 1988 approved in Germany). To prevent back-syphonage, the water connection must be via an approved Dual-CheckValve. After installing and connecting the machine to the services ensure that all outer panels have been put back in place.
Installation Electrical connection Steam connection All electrical work must be carried out by a suitably qualified and competent person in compliance with national and local regulations. Steam connection must only be undertaken by an authorised installer. Please take note of the Installation Diagram and instructions supplied. They are important for steam connection. Please take note of the Wiring diagram and the Installation Diagram and instructions supplied.
M.-Nr.
Miele Co. Ltd. Fairacres, Marcham Road, Abingdon OX14 1TW tel. (01235) 554455 fax (01235) 554477 Service Office, tel. (01235) 554466 Internet: www.miele.co.uk Telephone calls may be monitored and recorded to improve our service. Alteration rights reserved This paper consists of cellulose which has been bleached without the use of chlorine 09.
