User manual
Table Of Contents
- Contents
- Caring for the environment
- Warning and Safety instructions
- Operating the washing machine
- Before using for the first time
- Washing environmentally and economically
- 1. Prepare the laundry
- 2. Select a programme
- 3. Select programme settings
- 4. Load the washing machine
- 5. Add detergent
- 6. Starting the programme
- 7. End of programme
- Spinning
- Programme chart
- Extra options
- Wash programme chart - Extras
- Programme sequence
- Changing the programme sequence
- Garment care label symbols
- Favourite programmes
- Washing assistant
- Timer
- Detergent
- The correct detergent
- The right amount to dispense will depend on the following:
- Water softeners
- Dispensing aids
- Refill packs of detergent
- Fabric conditioner and liquid starch
- Adding fabric conditioner or liquid starch separately
- Colour run and dye removers/dyes
- Recommended Miele detergents
- Recommended detergents in accordance with Directive (EU) Nr. 1015/2010
- Cleaning and care
- Problem solving guide
- The programme does not start
- Fault message after a programme has been interrupted.
- Fault message at the end of a programme
- Fault message at the end of a programme
- Messages or faults with the TwinDos system
- Messages or faults with the TwinDos system
- General problems with the washing machine
- General problems with the washing machine
- General problems with the washing machine
- An unsatisfactory wash result
- The door will not open
- Opening the door in the event of a blocked drain outlet and/or power cut
- Service
- Installation
- Front view
- Rear view
- Installation surface
- Transporting the washing machine to its installation site
- Removing the transit bars
- Fitting the transit bars
- Levelling the machine
- The water protection system
- Connection to the water supply
- Operation with cold water and alternative water supply
- Water drainage
- Electrical connection
- Consumption data
- Technical data
- Settings
- Detergents and care products
Installation
*INSTALLATION*
102
Electrical connection
The washing machine is supplied with
an electrical connection cable with
moulded plug ready for connection to a
switched socket.
The socket must be easily accessible
after the washing machine has been in-
stalled. If that is not possible, ensure
that a suitable means of disconnection
is provided on the installation side for
each pole.
Risk of fire from overheating.
Connecting the washing machine to
a multi-socket plug adapter or to an
extension lead can overload the
cable.
Do not use an extension lead or
multi-socket plug adapter.
The electrical system must comply with
local and national safety regulations
(BS7671 in the UK). We recommend
the use of a suitable RCD .
If the connection cable is damaged, it
must only be replaced with a specific
connection cable of the same type
(available from the Miele Customer Ser-
vice Department). For safety reasons,
such replacement may only be carried
out by a qualified technician or the
Miele Customer Service Department.
The data plate indicates the nominal
power consumption and the appropri-
ate fuse rating. Compare the specifica-
tions on the data plate with those of the
electricity supply and make sure that
they match.
If in any doubt, consult a qualified elec-
trician.
Temporary or permanent operation on
an autonomous power supply system or
a power supply system that is not syn-
chronised with the mains power supply
(e.g. island networks, back-up systems)
is possible. A prerequisite for operation
is that the power supply system com-
plies with the specifications of
EN50160 or an equivalent standard.
The function and operation of the pro-
tective measures provided in the do-
mestic electrical installation and in this
Miele product must also be maintained
in isolated operation or in operation that
is not synchronised with the mains
power supply, or these measures must
be replaced by equivalent measures in
the installation. As described, for ex-
ample, in the current version of BS OH-
SAS 18001–2 ISO 45001.