Model #of burners and control method C-F40-NG (LP) 3 pieces Integrated control C-F50-NG (LP) 4 pieces Integrated control C-F75-NG (LP) 5 pieces Integrated control Gas Species Intake-tube pressure (in.W.C.) Per BTU B.T.U./h Total BTU B.T.U./h Nozzle No. Natural Gas 4 34,000 102,000 #36 L.P. Gas 10 30,000 90,000 #52 Natural Gas 4 34,000 136,000 #36 L.P. Gas 10 30,000 120,000 #52 Natural Gas 4 34,000 170,000 #36 L.P. Gas 10 30,000 150,000 #52 5.which must be signed by the carrier representative (Driver), and contact the carriers to pursue a claim within 15 days after receiving; Check all accessories complete. Refer to P18 table 4; Be sure to install supporting legs before using, and do not tear up any label or logo before normal using; Please read these instructions carefully before installation and operation.
6.2、Debugging It’s very important to debug the new stove. Through the comprehensive system test of equipment, we can ensure function and safety performance of products. Discovering any potential problems before use (such as equipment’s placement, ventilation, operation, etc), can avoid costly losses. 7. Safety Notices and Precautions Warning! For your safety, do not place petrol and other flammables nearby. Please keep clean and free of flammables surroundings. (Read ANSI Z83.
Steel cutting producers used to manufacture with sharp edges. The manufacturer has dealt with these sharp edges during production, however, we insist the operator take care when in contact with this piece of equipment; Always keep hands, hair and clothing away from heating source. Wait the unit cools down before cleaning. Because the unit is too hot to handle after using. 8. Operating Instructions Before operating, make sure to place the unit horizontally by adjusting bottom adjustable legs. 8.
●Press down safety valve and turn to “OFF”. 8.4、Cooking ●Before using the equipment for the first time, please use a mild detergent to wipe it for cleaning. Do not use corrosive or abrasives detergent.
with clean and mixed detergent clothing, second, wipe it dry with a clean clothing, do not use vinegar or corrosive liquid wiping.
●Check and adjust pressure regulator Supplied gas pressure regulator is factory set at 4”Natural Gas W.C, and L.P. Gas pressure is factory set at 10”Natural Gas W.C; Use a pressure gauge which is equipped with liquid (such as U-type pressure gauge, the minimum value is 0.1mbar) or a digital pressure gauge to test. Steps are as following: 1、Open cabinet door, remove needle type pressure joint screw arbor (Fig.
Connection Diagram ●Check and adjust automatic safety controller The flame should surround thermoelectric couple 1/2 inches, the fire must be large enough to keep the thermocouple being red, or can not keep the safety valve open. 1、Remove controller coppery adjusting cap; 2、Adjust controller knob, ensure appropriate flame(B). A is incorrect set. 3、Reset adjusting cap.
11. Troubleshooting
Problems Not lighting Ignite the pilot light but not the main fire Possible causes 1.Insufficient pressure in pipe gas 1.Contact the local gas supply dept. 2.Nozzle occlusion 2.Dredge nozzle 1.Insufficient gas pressure in pipe 2.The main fire nozzle occlusion 3.Gas control valves have problems 4.The pilot light and the main fire’s distance is too far 1.Contact the local gas supply dept. 1.Insufficient pressure in pipe 2.Dredge nozzle 3.Change gas control valves 4.12. Spare Parts The use of parts provided by other companies, our company has the right not to provide warranty service; Order replacement parts from authorized representatives and after-sale service agency. Provide the model no., serial no. and description when you order components. Fig.
Dimensions No. Matters Code Component name Qty Remark (mm)/Model 1 21201001001 Body assembly 1 21201003001 1.12 13 14 21201001013 21201003010 21201001006 21201002006 21201003006 21201001002 21201002002 21201003002 External upper smokestack assemble assembly 1 Internal upper smokestack assemble assembly 1 hydro-cylinder assembly 1 3 4 5 3 4 5 396*240*158 536*240*158 278*268*98 348*268*98 418*268*98 397*706*438 397*706*438 537*706*438 15 301060011 Nozzle joint 16 301040002(NG) 301040003(LP) Fryer Nozzle(NG) Fryer Nozzle(LP) 17 301050006 Fire assembly 1 18 301170012 intake-tube combination valv
29 301110002 30 301060001 31 301060002 Adjustable steel leg Needle type pressure joint Needle type pressure joint screw arbor 4 1 1 C-F40-NG(LP)\50NG(LP)\75-NG(LP) C-F40-NG(LP)\50NG(LP)\75-NG(LP) C-F40-NG(LP)\50NG(LP)\75-NG(LP) 13.
Intertek N IT E US LI S T E D SA C CM D CM A T I O N LI S T Conforms to ANSI STD Z83.11-2016 Certified to CSA STD 1.8-2016 Conforms to NSF/ANSI STD.4 Intertek 4003935 Our products have the advantages of good durability and low maintenance charge. But to update some components and necessary maintenance, can prolong life length of the products. Contact the dealer for assistance. In order to avoid confusion, please follow the format in figure 8 and table 3. Migali Industries, Inc.