C-HP-6-36-NG(LP) 4.2、Information of Gas Supply and Burner The minimum supplied gas pressure regulator is factory set at 4”Natural Gas W.C, and 10”L.P. Gas W.C. The external thread of product’s intake-tube is 3/4 inches.
Model #of burners and control method C-HP-2-12 -NG(LP) 2 pieces Independent control C-HP-4-24 -NG(LP) 4 pieces Independent control C-HP-6-36 -NG(LP) 6 pieces Independent control Gas Species Intake-tube pressure （in.W.C.） Per BTU B.T.U./ h Total BTU B.T.U./h Nozzle No.5. Transport and Storage In the process of transportation, handle carefully and keep upright to prevent damage of the product packing. Wrapped equipment should not be in open air for a long time, and shall be placed in a well-ventilated and non-corrosive gases warehouse. When equipment needs temporary storage, rainproof measures should be taken. 6. Installation and Debugging Any erroneous installation, adjustment, refit, overhaul or maintenance may cause property damage or personal injury.
corners of the charbroiled bottom, ensure sufficient space for ventilation; Adjustable stainless steel legs to make the equipment level, and get the same level with other series of the same stove; Please lift the equipment rather than drag if you need to move it; Supplied gas pressure regulator is factory set at 4”Natural Gas W.C, and 10”L.P. Gas W.
equipment’s placement, ventilation, operation, etc), can avoid costly losses. 7. Safety Notices and Precautions Warning! For your safety, do not place petrol and other flammables nearby. Please keep clean and free of flammables surroundings. (Read ANSI Z83.14B, 1991 for reference) Warning! Any erroneous installation, adjustment and refit may cause property damage or personal injury and maintenance failure. Read the instructions carefully before installation and using.
8. Operating Instructions Before operating, make sure to place the unit horizontally by adjusting bottom adjustable legs, and place the catch tray properly. The pilot light has been set at the factory. Each burner has a pilot light. 8.1、Lighting the pilot light Turn the control valve at the position of “0”(Fig.2), make sure all knobs are in the close state. Light and hold an ignition source at the pilots. The pilot light may not be lighted immediately, for existing gas in the pipe.
Turn the burners on about 15-20 minutes before broiling for preheating, according to the cooking requirement to adjust the flame size. Notice: When first preheating, the furnace will smoke above. This is caused by protective lipids on the grates and other parts are heated, it is normal, and it will be eliminated after the power up to the maximum for burning an hour. 8.
detergent! Warning: Before cleaning, all control valves must be turned off.
10.Troubleshooting
Problems Possible causes Problem solving Not lighting 1.Insufficient gas pressure in pipe 1.Contact the local gas supply dept. 2.Nozzle occlusion 2.Dredge nozzle 1.Insufficient gas pressure in pipe 2.The main fire nozzle occlusion 1.Contact the local gas supply dept. 3.Gas control valves have problems 3.Change gas control valves Ignite the pilot light but not the main fire Close gas and heard a sound of fire Yellow flame and black smoke 2.Dredge nozzle 4.11. Spare Parts The use of parts provided by other companies, our company has the right not to provide warranty service; Order replacement parts from authorized representatives and after-sale service agency. Provide the model number, serial number and description when you order components. Fig.
Matters No. Dimensions Component name Qty Code 1 301110001 (mm)/Model Adjustable steel legs 4 21103001014 2 21103002014 Catch tray 1 21103003014 3 4 301081006 301140001 Galvanized American outside six corner with pad tapping Kirsite knob 30 21103002027 Control panel 6 surround 507*620*26.5 C-HP-2-12-NG(LP) 807*620*26.5 C-HP-4-24-NG(LP) 1107*620*26.5 C-HP-6-36-NG(LP) ST4.8*12.10 2110300103 1 11 2110300103 Air input pipe-short Air input pipe-long 2 12 21105001003 Nozzle stator 1 C-HP-2-12-NG(LP) 2 C-HP-4-24-NG(LP) 3 C-HP-6-36-NG(LP) 1 C-HP-2-12-NG(LP) 2 C-HP-4-24-NG(LP) 3 C-HP-6-36-NG(LP) 2 C-HP-2-12-NG(LP) 4 C-HP-4-24-NG(LP) 6 C-HP-6-36-NG(LP) 2 13 14 15 16 17 18 19 20 21 301060003 Pilot light head 301060001 Needle type pressure joint 301060002 Needle type pressure joint screw arbor 301990001 301081002 301010005 301081001 301990004
1 22 23 24 25 26 301010006 301020004 21103002016 301990004 21103001015 Long ejector Octangular cooking grates Diaphragm gland Burner back plate 2 C-HP-2-12-NG(LP) Y-0002 3 C-HP-6-36-NG(LP) 2 C-HP-2-12-NG(LP) 4 Y-0004 C-HP-6-36-NG(LP) 0 C-HP-2-12-NG(LP) 1 578*52*16 Unit C-HP-6-36-NG(LP) 2 C-HP-2-12-NG(LP) 4 C-HP-4-24-NG(LP) 6 C-HP-6-36-NG(LP) 1 C-HP-2-12-NG(LP) 2 1 21203003001 28 29 301030014 pressure maintaining valve 301070007 Double burners countertop hot plate
Name Qty Model 12. Accessories List
C-HP-2-12-NG(LP) C-HP-4-24-NG(LP) C-HP-6-36-NG(LP) Adjustable steel legs 4 pieces 4 pieces 4 pieces Catch tray 1 piece 1 piece 1 piece pressure maintaining valve 1 piece 1 piece 1 piece A18 nozzle 2 piece 4 piece 6 piece instructions 1 piece 1 piece 1 piece Notice: 1、Pressure maintaining valve connects with air intake, must be installed by authorized and licensed technicians, to ensure interface tightness. 2、Screw the hex nut (Fig.Intertek N IT E US LI S T E D SA C CM D CM A T I O N LI S T Conforms to ANSI STD Z83.11-2016 Certified to CSA STD 1.8-2016 Conforms to NSF/ANSI STD.4 Intertek 4003935 Our products have the advantages of good durability and low maintenance charge. But to update some components and necessary maintenance, can prolong life length of the products. Contact the dealer for assistance. In order to avoid confusion, please follow the format in figure 8 and table 4.
