Safety & Operating Instructions Vacuum: Mulit-Surface VMS25 & VMS25E Serial No. P/N 805-0411 Read and understand this manual and all instructions before operating the Multi-Surface Vacuum. MacKissic Inc. 1-800-348-1117 www.MacKissic.com info@Mackissic.
Table of Contents Chapter 1: General Safety Rules .......................................................................................................................................... 3 Chapter 2: Setting Up the Multi-Surface Vacuum ................................................................................................................ 7 Chapter 3: Operating the Multi-Surface Vacuum .................................................................................................................
Chapter 1: General Safety Rules Read this safety & operating Instructions manual before you use the MULTI-SURFACE VACUUM. Become familiar with the operation and service recommendations to ensure the best performance from your machine. If you have any questions or need assistance, please contact us at www.MacKissic.com or call toll-free 1-800-348-1117 and one of our Technical Support Representatives will be happy to help you.
Protecting Yourself and Those Around You This is a high-powered machine, with moving parts operating with high energy at high speeds. Use proper clothing and safety gear when operating this machine to prevent or minimize the risk of severe injury. You must operate the machine safely. Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area.
Safety with Gasoline-Powered Machines Gasoline is a highly flammable liquid. Gasoline also gives off flammable vapor that can be easily ignited and cause a fire or explosion. Never overlook the hazards of gasoline. Always follow these precautions: • Never run the engine in an enclosed area or without proper ventilation as the exhaust from the engine contains carbon monoxide, which is an odorless, tasteless, and deadly poisonous gas.
General Safety Operating this vacuum safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe operation can create a number of hazards for you. Always take the following precautions when operating this vacuum: • Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and themselves. • Your Multi-Surface Vacuum is a powerful tool, not a plaything. Exercise extreme caution at all times.
Chapter 2: Setting Up the Multi-Surface Vacuum It may be helpful to familiarize yourself with the controls and features of your Multi-Surface Vacuum as shown in Figure 1 before beginning these procedures. If you have any questions at all, please feel free to contact us at www.MacKissic.com or call 1-800348-1117.
Specifications Engine Impeller Drive Method Impeller Speed Height Adjustment Range Collection Bag Volume Overall Length Overall Height Width Machine ship Weight Manual Start See Engine Owner’s Manual Direct Drive 145 MPH 5/8" to 4" 4 bushels 67" 43" 25.5" 187 Lbs. Electric Start See Engine Owner’s Manual Direct Drive 145 MPH 5/8" to 4" 4 bushels 67" 43" 25.5" 197 Lbs. Unpacking the Multi-Surface Vacuum Tools Needed: 3 • Utility Knife 6 7 2 1.
4 6 8 Hardware Bag Contents (Figure 4 and Table Below) ITEM# 1 2 3 4 5 6 7 8 9 PART# 090-0502 805-0326 DESCRIPTION 5/16 FENDER WASHER CARABINEERS 805-0119 090-0088 090-0418 090-0460 090-0232 090-0503 BAG HANGER HOOKS 5/16-18 X 1” HHCS 5/16-18 WHIZ LOCKNUT 5/16-18 NYLOCK NUT 5/16 FLAT WASHER 5/16-18 SELF TAPPING HHCS QTY 6 2 3 10 3 14 2 4 3 9 2 1 7 Figure 4 Compare the contents of the Shipping Box, Poly Bag and Hardware Bag with the “Contents” lists above.
4. Locate the two Carabiners, three Bag Hanger Hooks and four 5/16-18 Wiz Nuts included in the Bolt Bag. Mount the two upper Hooks through the upper holes in the Handlebar Assembly with the Hooks on the inside (Figure 8). Secure with a Wiz Nut on the outside of the Upper Handlebar. Upper Handlebar Lower Handlebar Bolts and Locknuts 5. Thread a Wiz Nut onto the one remaining Hook as far as it will go on the threads so that the flat side of the Nut is facing away from the Hook (See detail). 6.
Note: Installation of the Vacuum Snout will be easier if the front of the machine is raised. See “Adjusting the Vacuum Snout Height” on page 16 to raise the front of the machine. Detail Detail B Safety Switch 5/16-18 Nylocks Plunger Bracket Figure 12 11. Place the Vacuum Snout onto the front of the Housing (Figure 12) so the studs are located in the right-hand side of the lower slots (Detail A).
Before starting engine, always check oil level. Refer to the following section Adding the Engine Oil and Gasoline You must add oil before starting the engine. This machine is shipped without oil. Traces of oil may be in the reservoir from factory testing, but you must add oil before starting the engine. Fill the reservoir slowly, checking the level frequently to avoid overfilling. To Add Engine Oil 1. Remove the yellow oil fill cap from the right hand side of the engine (Figure 16).
Chapter 3: Operating the Multi-Surface Vacuum It may be helpful to better familiarize yourself with the features of your MultiSurface Vacuum by reviewing Figure 1 in Chapter 2 before beginning the steps outlined in this chapter. Always refer to the Engine manual for more specific Engine information. Fuel Shut Off Choke On/Off Switch Starting the Engine (manual Start) 1. Move the Choke Control Lever to the “CHOKE” position (leave in the run position if the engine is already warm) (Figure 19A). 2.
Installing or Emptying the Collection Bag Use the bag at all times - failure to do this could cause serious injury. • Empty the bag as soon as it is full (check by feeling sides of bag). Overfilling the bag will cause the vacuuming performance to decrease or stop completely and could lead to clogging of the discharge tube, snout, or both.
Adjusting the Vacuum Snout Height 1. The height of the vacuum snout can be adjusted to allow you to vary the suction to meet the surface conditions. For short turf with light leaf fall, it can be lowered to 1-1/4" off the surface. For long turf and heavy leaf fall, it should be raised to the upper setting about 2 3/4 inches. 2. For moving the machine long distances, you will avoid damage to the snout by raising it to the highest setting. 3.
Operating Safety • • The operation of any Multi-Surface Vacuum can result in foreign objects being thrown into the eyes, which can result in severe eye damage. Always wear the safety glasses provided with the Multi-Surface Vacuum or eye shields during use or while performing any adjustments or repairs. Only operate your Multi-Surface Vacuum from the operator position.
16 MULTI-SURFACE VACUUM Chapter 4: Maintaining the Multi-Surface Vacuum Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's owner's manual for maintenance procedures. Service intervals listed in the checklist below supersede those listed in the engine manufacturer's owner's manual.
CONTACT US AT www.MacKissic.
Battery Care (electric start machines) Proper care can extend the life of a Battery. Follow these recommendations to ensure your Battery’s best performance and long life: • Do not allow the Battery charge to get too low. If the machine is not used, charge the Battery every 4 – 6 weeks. Operate the Engine for at least 45 minutes to maintain proper Battery charge. • Store an unused Battery in a dry area that does not freeze. • Do not charge an already charged Battery.
Chapter 5: Vacuum Kit Accessory #805-0129 Shut down the engine, remove the spark plug wire and wait 5 minutes for parts to cool before performing before installing the Vacuum Kit. 1 5 Tools Needed: 2 • • • 3 • • 5/16" Wrench 7/16" Wrench Short Flat Head Screwdriver Wire Cutters Utility Knife 1. Cut the Tape on the Box Flaps with a Utility Knife. 6 2. Remove the parts from the Box and lay them out on a flat clean area.
4. Place the Vacuum Adapter onto the front of the Housing (Figure 25) so the studs are located in the right-hand side of the lower slots (Detail A). Slide the Adapter to the right and down so the Plunger Bracket on the Adapter pushes the Safety Switch in (Detail B). 5. Install four 5/16-18 nylon locknuts, with the Cable Guide under the top Knob, onto the studs to secure the Vacuum Adapter. 5/16-18 Nylocks Cable Guide Safety Switch Plunger Bracket Vacuum adapter Detail B Figure 25 6.
Chapter 6: Troubleshooting Most problems are easy to fix. Consult the Troubleshooting Table below for common problems and their solutions. If you continue to experience problems, contact us at www.MacKissic.com or call toll-free 1-800-348-1117 for support. Shut down the engine, remove the spark plug wire and wait 5 minutes for parts to cool before performing any maintenance procedure or inspection on the Machine.
Troubleshooting Table (Continued) Shut down the engine, remove the spark plug wire and wait 5 minutes for parts to cool before performing any maintenance procedure or inspection on the vacuum. SYMPTOM POSSIBLE CAUSE ; CORRECTIVE ACTION Loss of traction Gear shift lever does not shift Wheels do not stop when Wheel Drive Bail Cable is released Product build-up in shredding chamber. 22 Drive belt loose; Adjust wheel drive bail cable.
Chapter 7: Parts Lists, Schematic Diagrams and Warranty Parts List – MAIN ASSEMBLY NOTE: Part numbers listed are available through MacKissic Inc. ITEM NO.
Schematic – MAIN ASSEMBLY 24 MULTI-SURFACE VACUUM
Parts List – FINAL ASSEMBLY NOTE: Part numbers listed are available through MacKissic Inc. ITEM NO.
Schematic – FINAL ASSEMBLY 26 MULTI-SURFACE VACUUM
Parts List – OPTIONAL VACUUM KIT #805-0129 NOTE: Part numbers listed are available through MacKissic Inc. Ref# Part# 01 02 03 04 05 06 07 805-0338 32412 32027-B 900-0074A 090-0179 704-0117 090-0470 Description Adapter, Vacuum Clamp, Hose, 6-1/8" Hose, 6" Dia.
Daily Checklist for the Multi-Surface Vacuum To help maintain your Multi-Surface Vacuum for optimum performance, we recommend you follow this checklist each time you use your machine. Shut down the engine, remove the spark plug wire and wait 5 minutes for parts to cool before performing any maintenance procedure or inspection on the Machine. [ ] Check the engine oil level. [ ] Check Fuel Level [ ] Check the general condition of the Vacuum, e.g.; nuts, bolts, welds, etc.
