Instructions / Assembly

2
rev - 09-20-10
ON
ALARM ACCESSORY RCVR
SEQ1
SEQ2
LEARN
BLU ORG WHT GRN
R B G
Connect #1 wire from the
RELAY OUTPUT terminals
on the keypad to WHT
terminal on the gate opener
control board.
Connect #2 wire
from the RELAY OUTPUT
terminals on the keypad to the
GRN terminal on the gate
opener control board.
PRO-1000/2000, PRO-SL1000/SL2000 and Old Mighty Mule
Control Boards
#1
#2
RELAY
OUTPUT
AC/DC
POWER IN
123456789
+
0
–
Jumper ON
wireless mode
Jumper OFF
Hard-wire from Gate Opener
Power Supply from
Opener Battery
#
1
#
2
wired mode
Step 2: Strip 3/16" off the ends of one pair of low voltage wires. Attach the wires to the terminal
block marked RELAY OUTPUT on the keypad control board as shown. Connect the other
end of the wires to the gate opener’s control board as shown in Control Board Connections
(below).
Step 3: Strip 3/16" off the ends of the second pair of low voltage wires.
Attach the wires to the terminal block marked AC/DC POWER IN
on the keypad control board as shown. Connect the other end of
the wires to the opener’s battery: one end to the POSITIVE
(RED) pole and the other to the NEGATIVE (BLACK) pole.
Step 4: Connect the jumper between the two terminals on the
keypad control board (ON) as shown.
Step 5: Slide the keypad into the
housing and secure with the small
screws provided.
Step 6: Replace the control board cover
and turn the power switch ON.
1
2
ABC
3
DEF
4
GHI
5
JKL
6
MNO
7
PRS
8
TUV
9
WXY
0
CALL
STATUS
PROGRAM
CALLING
GRANTED
Control Board Connections
If your control board doesn’t look like any of these diagrams, please refer to your gate opener
installation manual or call GTO Technical Service at 1-800-543-1236 or 850-575-4144.
GRN BLK RED
RECEIVER
COM COM
CYCLE
CLOSE
CYCLE
CLOSE
SAFETY
EXIT
OPEN
SHADOW
LOOP
CLOSE
EDGE
OPEN
EDGE
J11
J11
J8
J12
GTO/PRO DC Powered PRO-SW3000
and PRO-SW4000 Control Boards
Connect #1 wire from the
RELAY OUTPUT terminals on
the keypad to CYCLE terminal on
the gate opener control board.
Connect #2 wire from
the RELAY OUTPUT
terminals on the keypad
to the COM terminal on
the gate opener control
board.
#1
#2
RECR
GRN
BLK
RED
EXIT
SAFETY
EDGE
CYCLE
COMMON
LINK
Mighty Mule 350 Control Board
Connect #1 wire from the
RELAY OUTPUT terminals
on the keypad to CYCLE
terminal on the gate opener
control board.
Connect #2 wire from the RELAY
OUTPUT terminals on the keypad
to the COMMMON terminal on
the gate opener control board.
#1
#2
RECEIVER
COM COM
CYCLE CLOSE SAFETY EXIT/ OPEN SHADOW LOOP CLOSE EDGE OPEN EDGE
BLKGRN RED
Mighty Mule 500 & 502
Control Boards
Connect the #1 wire from
RELAY OUTPUT terminals on the
keypad to the CYCLE terminal on
the opener control board.
Connect the #2 wire from
the RELAY OUTPUT
terminals on the keypad to
one of the COMMON
terminals on the opener
control board.
#1
#2
RECEIVER
ALM
GTO RCVR.
COM
GRN
BLK
RED
CYCLE
SAFETY
EXIT
SHADOW
OPEN
EDGE
COM
CONTROL INPUTS
CLOSE
EDGE
Connect #1 wire from
the RELAY OUTPUT terminals
on the keypad to CYCLE terminal
on the gate opener control board.
Connect #2 wire from the
RELAY OUTPUT terminals
on the keypad to the COM
terminal on the gate opener
control board.
#1
#2
GEN-3 (Blue) Control Boards
COM COM COM
GTO Inc.
SX4000 L
CYCLE
SAFETY
OPEN EDGE
RUN 2
OPEN
CLOSE
STOP
COM COM COM
SHADOW
LOOP
Connect #1 wire from the
RELAY OUTPUT
terminals on the keypad to
CYCLE terminal on the
gate opener control board.
Connect #2 wire from the
RELAY OUTPUT terminals
on the keypad to the COM
terminal on the gate opener
control board.
#1
#2
GTO/PRO GP-SL100 and GP-SW100
Control Boards
3. Test Keypad
Turn the gate opener power switch to ON. Test the keypad by entering “1234.”