Installation Guide

ManualsBrandsMighty Mule ManualsSensorsFM145

Thank you for purchasing the GTO Bulldog Pedestrian Gate Lock.

Be sure to read the directions carefully and completely.

Limited One Year Warranty

GTO Access Systems, LLC gate opener accessories are warranted by the manufacturer against defects in workmanship for a period of

one (1) year from the date of purchase, provided recommended installation procedures have been followed.

In the case of product failure due to defective material or manufacturer workmanship within the one (1) year warranty period, the acces

sory will be repaired or replaced (at the manufacturer’s option) at no charge to the customer, if returned freight prepaid to GTO Access

Systems, LLC, 3121 Hartsﬁeld Rd., Tallahassee, FL 32303. IMPORTANT: Call 850/575-4144 or fax 850/575-8950 for a Return Goods Autho-

rization (RGA) number before returning goods to factory. Products received at the factory without an RGA will not be accepted. Replace-

ment or repaired parts are covered by this warranty for the remainder of the one (1) year warranty period or six (6) months, whichever is

greater. GTO Access Systems, LLC will pay the shipping charges for return to the owner of items repaired.

The manufacturer will not be responsible for any charges or damages incurred in the removal of the defective parts for repair, or for the

reinstallation of those parts after repair. This warranty shall be considered void if damage to the product(s) was due to improper installa

tion or use, connection to an improper power source, tampering, or if damage was caused by lightning, wind, ﬁre, ﬂood, insects, or other

natural agent.

After the one (1) year warranty period, GTO Access Systems, LLC or one of its authorized service centers will make any necessary repairs

for a nominal fee. Call GTO Access Systems, LLC at 850/575-4144 for more information. This warranty gives you speciﬁc legal rights, and

you may also have other rights which may vary from state to state. This warranty is in lieu of all other warranties, expressed or implied.

NOTE: Veriﬁcation of the warranty period requires copies of receipts or other proof of purchase. Please retain those records.

rev - 12.07.15 • Printed in China for GTO Access Systems, LLC

PEDESTRIAN GATE LOCK

Installation Manual

Features

• One year* of operation with 4 x AA alkaline batteries

(no transformer or solar panel is required)

• Accepts either standard alkaline or rechargeable batteries

• Built-in charger circuit for rechargeable batteries (must use

with transformer or solar panel)

• Accepts door bell push button for easy exit from inside

property

• Up to 25 programmable entry codes (permanent and

temporary codes)

• Temporary codes can be programmed to automatically

expired (1 to 7 days)

• Daylight sensor that automatically turns on backlight when

button is pressed in low light conditions

• Automatically disables the unit after 20 key presses for

40 seconds to discourage unauthorized entry

• Programmable lock-hold time from 1-9 seconds

(default at 3 seconds)

Note: Longer lock hold time will reduce battery life when

using alkaline batteries

* Based on typical usage of 10 times/ day with 3 seconds lock-

hold time with fresh batteries.

Summary of content (10 pages)

PAGE 1
PEDESTRIAN GATE LOCK Installation Manual Thank you for purchasing the GTO Bulldog Pedestrian Gate Lock. Be sure to read the directions carefully and completely.
PAGE 2
Before You Start Materials you will need before you begin the installation. • For all installations use mounting hardware (not included) no greater than 5/16” diameter. Note: for a more secure installation, we suggest you use lock washers and/or lock nuts on all mounting hardware. • For most IRON and ALUMINUM TUBE gates (see Illustration C, page 6) use bolts, washers, and nuts to mount both the lock and the receiver.
PAGE 3
Table of Contents • • • • • • • • • • Features and Warranty------------------------------------------------------------------------------------ page 1 Before You Start--------------------------------------------------------------------------------------------- page 2 Parts Identification ----------------------------------------------------------------------------------------- page 3 Determine Mounting Location for Lock and Entry Control----------------------------------- page 4 Mounting the Lock-----------
PAGE 4
Determine Mounting Location for Your Lock Lock OPEN OPEN Lock Receiver Receiver A B Receiver Receiver OPEN OPEN Lock Lock C D Determine Mounting Location for Your Entry Control 1 Outside Property Possible Keypad Locations 2 Possible Push Button Locations 1 1 1 1 1 2 2 OPEN 2 Inside Property 4 2
PAGE 5
Mounting The Lock Step 1: With the gate in the closed position, determine the best location for the lock and lock receiver. Attach the lock to a solid surface or cross member to provide stability. Step 2: Hold receiver and lock together (with receiver pin hole and lock slot aligned) against the gate post, mark their positions to drill receiver holes (see Illustration B and C, page 3). The receiver must be mounted with carriage bolts, not U-bolts, to allow lock to seat properly.
PAGE 6
Illustration C Iron or Aluminum Tube Fence and Gate Installation Remember to check the alignment and mark positions before drilling holes in fence post and gate. Clevis Pin GTO Pedestrian Gate Lock Receiver Locking Cap Carriage bolts, washers, and nuts (not provided; size of fasteners depends on the gate) Illustration D Chain Link Fence and Gate Installation Remember to check the alignment and mark positions before drilling holes in fence post .
PAGE 7
Mounting the Keypad 1 4 2 ABC 5 GHI JKL 7 8 PRS TUV 3 DEF 6 MNO 9 WXY 0 Wiring Connections LOCK C MATI CK ® AUTO LOLOCK Y RIT GASETE CU IC TRON ELEC DOOR BELL PUSH BUTTON Knock-out (use 22 AWG wires minimum) OPTIONAL - TRANSFORMER + SOLAR PANEL OR (not included) IMPORTANT PWR + COM PWR LOCK+ LOCK - • DO NOT USE Transformer or Solar Panel with non-rechargeable batteries. CONTROL INPUTS PUSH BUTTON LOCK SOLENOID • DO NOT CONNECT both transformer and solar panel.
PAGE 8
Alternate Power Options When Using rechargeable nickel-metal hydride (NiMH) batteries: • Transformer or solar panel (not included) can be used to charge the battery. The control board has a trickle charge circuit to charge the batteries. • Highly recommended for heavy usage.
PAGE 9
Programming the Keypad Programming Interface: Delete An Entry Code: • All codes are four (4) digits in length. • Entry code is a four (4) digit code needed to activate the gate. • Master Code is needed to add, remove or reset entry codes. • Master Code also functions as the entry code under normal operation. • Factory default Master Code is 1234. • STATUS light should blink and beeper should beep (once) whenever any button is pressed.
PAGE 10
Delete ALL Entry Codes: Normal Keypad Operation: • Press and release PROGRAM button. • Enter the Master Code then press and release PROGRAM button. • Enter 0, 7 then press and release PROGRAM button. • Beeper beeps 3 times to confirm that the All Entry Codes are deleted. Example: Key press sequence to delete all entry codes from memory. (for example if 3121 is the Master Code) • If the user enters a 4-digit code that is matched to one of the 25 stored codes.