Product Manual B

MM-LPS13 Installation Manual 13
rev 05.16.13
DETERMINING THE GATE’S OPEN POSITION
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Operator
1234
ON
PULL/PUSH
SEQ1
SNGL/DUAL
SEQ2
Gate Opens Right
Dip Switch 4 Set to Push.
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Operator
1234
ON
PULL/PUSH
SEQ1
SNGL/DUAL
SEQ2
Gate Opens Left
Facing Gate
& Operator
Facing Gate
& Operator
Dip Switch 4 Set to Pull.
GATE OPENS RIGHT TO LEFT
GATE OPENS LEFT TO RIGHT
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Operator
1234
ON
PULL/PUSH
SEQ1
SNGL/DUAL
SEQ2
Gate Opens Right
Dip Switch 4 Set to Push.
1. KEEP CLEAR! Gate may move at any time.
2. Do not allow children to operate gate or
play in gate area.
3. This gate is for vehicles only. Pedestrians
must use a separate entrance.
Moving Gate Can Cause
Injury Or Death
WARNING
!
Operator
1234
ON
PULL/PUSH
SEQ1
SNGL/DUAL
SEQ2
Gate Opens Left
Facing Gate
& Operator
Facing Gate
& Operator
Dip Switch 4 Set to Pull.
GATE OPENS RIGHT TO LEFT
GATE OPENS LEFT TO RIGHT
RED
BLK
ORG
BLU
GRN
CLS EDG
OPN EDG
RED
GRN
ORG
BLU
WHT
BLK
ORG
BLU
GRN
CLS EDG
OPN EDG
LEARN
AUTOCLOSE
INERTIA
STATUS
PULL/PUSH
SNGL/DUAL
SEQ1
SEQ2
MIN
MAX
MIN
MAX
OFF
60
120
BATT
+
–
OBSTRUCT
SENS.
RCVR
R
B
G
ALARM
SECOND OPERATOR
FIRST OPERATOR
POWER IN
18VAC SOLAR
~ ~ – +
ACCESSORY
PWR. SW.
Red
Black
(–)
(+)
CC
CC
C
C
C
C
CC
C
Red
Jumper Wire
A jumper wire is a small piece of wire stripped
at both ends that can be discarded after
the limits are set on the operator.
Green
Black
RED
BLK
ORG
BLU
GRN
CLS EDG
OPN EDG
RED
GRN
ORG
BLU
WHT
BLK
ORG
BLU
GRN
CLS EDG
OPN EDG
LEARN
AUTOCLOSE
INERTIA
STATUS
PULL/PUSH
SNGL/DUAL
SEQ1
SEQ2
MIN
MAX
MIN
MAX
OFF
60
120
BATT
+
–
OBSTRUCT
SENS.
RCVR
R
B
G
ALARM
SECOND OPERATOR
FIRST OPERATOR
POWER IN
18VAC SOLAR
~ ~ – +
ACCESSORY
PWR. SW.
Red
Black
(–)
(+)
CC
CC
C
C
C
C
CC
C
Red
Jumper Wire
A jumper wire is a small piece of wire stripped
at both ends that can be discarded after
the limits are set on the operator.
Green
Black
Gate Opens Right to Left
Facing the gate (on same side as operator), the gate opens to the left,
place or leave the PULL/PUSH DIP switch in the “PULL” position.
Verify that the chain is completely removed from
operator and both chain brackets at this time.
Step 1
— Turn the control box power switch to the ON position.
Step 2 — Install a jumper wire. Wire one end of the jumper wire to the
accessory terminal marked GRN. Touch the other end
of wire to the BLU accessory terminal (see Illustration).
Step 3 — Operator motor will run then STOP.
Step 4 — Turn the control box power switch to the OFF position.
Step 5 — Remove jumper wire, charging source wires and disconnect
battery.
Step 6 — Manually slide the gate to the open position approximately
2-3”fromthefullyopenposition.
Step 7 — Re-install the chain on the chain brackets and the operator.
This is the gate’s OPEN position.
Step 8 — Connect the battery and charging source and turn the
operator to the ON position.
Step 9 — Press transmitter to close gate. The gate will move toward the
closed position and stop. You will need to adjust the closed
position for your gate application at this time. Proceed to
Adjusting the Limit Switch on page 14.
Gate Opens Left to Right
Facing the gate (on same side as operator) the gate opens to the Right,
place the PULL/PUSH DIP switch in the “PUSH” position.
Verify that the chain is completely removed from
operator and both chain brackets at this time.
Step 1
— Turn the control box power switch to the ON position.
Step 2 — Install a jumper wire. Wire one end of the jumper wire to the
accessory terminal marked GRN. Touch the other end
of wire to the BLU accessory terminal (see Illustration).
Step 3 — Operator motor will run then STOP.
Step 4 — Turn the control box power switch to the OFF position.
Step 5 — Remove jumper wire, charging source wires and disconnect
battery.
Step 6 — Manually slide the gate to the open position approximately
2-3”fromthefullyopenposition.
Step 7 — Re-install the chain on the chain brackets and the operator.
This is the gate’s OPEN position.
Step 8 — Connect the battery and charging source and turn the
operator to the ON position.
Step 9 — Press transmitter to close gate. The gate will move toward the
closed position and stop. You will need to adjust the closed
position for your gate application at this time. Proceed to
Adjusting the Limit Switch on page 14.
NOTE: If gate does not move, adjust the INERTIA and OBSTRUCT SENS.
settings located on page 15.