Instructions / Assembly

ManualsBrandsMighty Mule ManualsFencingWireless Intercom Keypad and Base Station Kit for Gate Openers

rev - 09-20-10

Crystal clear two-way wireless communication up to 500 feet

Wireless Gate Entry Intercom

Thank you for purchasing the Mighty Mule Wireless Gate Entry Intercom.

Please read the directions carefully and completely before installing.

Installation Instructions

GTO - Gates That Open, LLC • 3121 Hartseld Road • Tallahassee, Florida 32303

Telephone (850) 575-0176 • Fax (850) 575-8912 • www.mightymule.com

SAFETY NOTE:

NEVER install the keypad portion

of this system where a person can

reach through the gate to activate it,

or where a person can touch the gate

while activating the keypad.

The recommended minimum distance

between the gate and keypad is 10 ft.

IMPORTANT: Allow the

intercom base unit’s battery to

charge for 12 hours before using

the system for the rst time.

Keypad Unit

Base Unit

ACCESS CONTROLS

Summary of content (8 pages)

PAGE 1
ACCESS CONTROLS IMPORTANT: Allow the intercom base unit’s battery to charge for 12 hours before using the system for the first time. Base Unit Keypad Unit Wireless Gate Entry Intercom Installation Instructions Crystal clear two-way wireless communication up to 500 feet Thank you for purchasing the Mighty Mule Wireless Gate Entry Intercom. Please read the directions carefully and completely before installing.
PAGE 2
Features of the Wireless Intercom/Keypad The Wireless Intercom/Keypad has two separate units: the KEYPAD and the BASE UNIT. The keypad should be mounted outside the gate allowing visitors to press the CALL button from their vehicle. The base unit is powered by a rechargeable battery; the charge is maintained by the transformer. It can also be disconnected from the transformer allowing it to go anywhere within range for convenience.
PAGE 3
Keypad Description Keypad Front CALLING 1 4 GHI 7 PRS CALLING Light: LED is RED when calling and turns GREEN when call is answered. GRANTED Light: LED turns GREEN when access permission is granted. GRANTED 2 ABC 5 JKL 8 TUV 3 DEF 6 PROGRAM button: Used to program entry codes. STATUS Light: This LED will blink once when any key is pressed and provides visual feedback when programming entry codes.
PAGE 4
Step 2: Strip 3/16" off the ends of one pair of low voltage wires. Attach the wires to the terminal block marked RELAY OUTPUT on the keypad control board as shown. Connect the other end of the wires to the gate opener’s control board as shown in Control Board Connections (below). Step 4: Connect the jumper between the two terminals on the keypad control board (ON) as shown. Step 5: Slide the keypad into the housing and secure with the small screws provided.
PAGE 5
4. Program the Keypad Add Temporary Entry Code: Programming Interface/Keypad Operation: 1. Press and release PROGRAM button. 2. Enter the Master Code then press and release PROGRAM button. 3. Enter “8” and any number between 1 thru 7 then press and release the PROGRAM button. The second number (1 thru 7) indicates the number of days after which the code will be automatically removed from memory.* 4. Enter the new Entry Code then press and release PROGRAM button.
PAGE 6
Base Unit Description Base Unit Face POWER Light: GREEN: charging; RED: battery power mode (unplugged from transformer); Blinking RED: low battery. PUSH TO ANSWER/TALK Button: Use to answer CALL from keypad. PRESS and HOLD to talk; RELEASE to listen. En dC all Pu sh Ke Ba ypa tt d Lo w To A ns PO WE R Gra nt we r/T alk Pe rm iss ion KEYPAD BATTERY INDICATOR Light: LED turns ON when keypad battery is low.
PAGE 7
The base unit can be disconnected from the transformer for use in another location. The battery will last approximately four (4) hours when unplugged from the transformer. IMPORTANT: You can turn the base unit OFF to conserve battery power, however it will not receive a signal when OFF. 7. Add Additional Base Units (optional) Intercom ID Codes The keypad and base unit are programmed at the factory to communicate with each other, and do not need the ID Codes programmed.
PAGE 8
base unit is at least 30 feet. 3. Press the “ID SET” button on the keypad until you hear a beep, then release. This erases all stored ID Codes. 4. Press the “ID SET” button on the MASTER base unit for approximately 2 seconds then release. You will hear ONE beep from the base unit and TWO from the keypad, which means the ID Codes are reassigned. 5. Test the system by pressing the CALL button on the keypad to see if the base unit receives the signal.