Product Manual

rev - 09-20-10
The Wireless Intercom/Keypad has two separate units: the KEYPAD and the BASE UNIT. The keypad should be mounted
outside the gate allowing visitors to press the CALL button from their vehicle. The base unit is powered by a rechargeable
battery; the charge is maintained by the transformer. It can also be disconnected from the transformer allowing it to go
anywhere within range for convenience. Up to three additional base units can be added for convenience in different
locations throughout the house.
When someone without an access code approaches the gate, they can press the CALL button on the keypad which will
ring the base unit inside the house. To answer the CALL, the person inside presses and holds the ANSWER button to
talk to the person at the gate, releasing the ANSWER button to listen. To allow the person calling to open the gate, the
GRANT PERMISSION button must be pressed. Then the person at the gate can press any number key on the keypad to
open the gate. The END CALL button terminates the calls and the ON/OFF switch can be used to conserve power when
using unit on battery (note: the base station will not recieve a signal if turned OFF).
Up to 25 different personal Entry Codes may be programmed into the keypad, allowing you to give different temporary
and permanent Entry Codes to different users. For example, you can give a delivery person their own temporary entry
code, which you can easily change after he has made the delivery.
This will prevent him from being able to regain access,
while still allowing those to whom you gave permanent Entry Codes full access.
After entering a valid code, pressing any key on the keypad while the gate is opening will stop the gate; pressing any key
while the gate is stopped will cause the gate to reverse direction. The keypad will not af
fect the auto-close setting of your
gate opener system.
The keypad will light up and the unit will beep at the press of any key.
The keypad memory will recognize your entry
code in a string of up to 20 digits. If it nds the correct sequence, it will activate the gate opener.
As a security feature,
the keypad will shut down for 40 seconds if it does not nd the correct code sequence within a 20-digit string. This will
discourage an unauthorized person from trying to use random numbers to access your property.
Entry Codes will remain stored in memory even when the batteries go dead. The keypad will remember your Entry Codes
as long as you don’t press the RESET button.
FCC WARNING: Changes or modications to this unit not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in particular installations. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures: • Reorient or replace the receiver
antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help.
Features of the Wireless Intercom/Keypad
IMPORTANT: In areas of high radio frequency (RF) interference, the keypad may need to be connected (hard
wired) directly to the gate opener using 16 gauge (AWG) stranded, direct burial, low voltage wire (RB509, not
included).
The contents of all material available on this installation manual are copyrighted by Gates That Open, LLC (“GTO”), unless otherwise indicated. All rights are reserved by GTO, and
content may not be reproduced, downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GT
O. Any reprinting of GTO
publications is by permission only. Copyright infringement is a violation of federal law.
GTO®, GTO/PRO®, Mighty Mule® are registered trademarks of GTO - Gates That Open, LLC. GTO Access Systems™ is a trademark of GTO - Gates That Open, LLC. These marks are the
exclusive property of GTO - Gates That Open, LLC (“GTO”). All rights are reserved by GTO, and these marks may not be used, in any form, without the prior, written permission of GTO.