Instructions / Assembly

8-Foot Sectional Door Header Extension Bracket
LIMITED WARRANTY
GTO Access Control, LLC (the Company) warrants to the original purchaser that products delivered hereunder will be free of defects in material and workmanship for one year from the date of purchase. The Company within said period shall at
its option, either repair or replace free of charge, any product or part thereof found, upon the Company’s inspection, to be so defective, and will return the repaired or replaced product to the purchaser at Company’s expense. For warranty
service and shipping instructions contact 1-800-543-4283. Devices must be sent to the Company at owner’s expense and be accompanied with statement of defect and proof of purchase. This warranty is conditioned on the following: 1). The
Company must be notifi ed within the period of the warranty from the date of purchase and have been given the opportunity of inspection by return of any alleged defective product free and clear of all liens and encumbrances to the Company
or its distributor; and 2). The product must not have been abused, misused or improperly maintained and/or repaired during such period; and 3). such defect has not been caused by corrosion or exposure to other than ordinary wear and
tear. THE COMPANY MAKES NO OTHER WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER EXPRESS OR IMPLIED, AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. The Company’s maximum liability hereunder is limited to the purchased price of the product. In no event shall the Company be liable for any consequential,
indirect, incidental or special damages of any nature arising from the sale or use of the product, whether based in contract, tort, strict liability or otherwise. Note: Some states do not allow limitations on incidental or consequential damages
or how long an implied warranty lasts so that the above limitations may not fully apply. This warranty gives specifi c legal rights and you may also have other rights which may vary from state to state.
PRINTER’S INSTRUCTIONS:
ARTWORK,BLISTER CARD,MMEXT8 - GTO P/N: 10018594A - INK: BLACK - MATERIAL: .005” THICK (150 GSM) WHITE PAPER C2S - 2 SIDED - SIZE: 6.5.000” X 11.000” FOLDED TO 6.5” x 5.5” - SCALE: 1-1
PLACE OPENER ON
THE EMPTY CARTON
WITH THE RAIL
TOWARDS THE DOOR
RAISE THE RAIL TO
ALIGN IT WITH THE
HEADER BRACKET
MARK THE CENTERLINE
OF THE DOOR ON THE
WALL AND THE TOP
DOOR PANEL
CLOSE THE DOOR FROM
INSIDE THE GARAGE
IF SO, ATTACH A 2 X 6
CROSS PIECE BETWEEN
TWO STUDS TO CREATE
A LOCATION FOR THE
HEADER BRACKET
IN SOME INSTALLATIONS, THE CALCULATED
BRACKET LOCATION WILL BE ABOVE THE
DOOR HEADER
USE LAG SCREWS
(NOT SUPPLIED) TO
ATTACH THE CROSS PIECE
DOOR
HEADER
DRILL TWO 3/16" PILOT HOLES
ABOUT 2" DEEP AT THE BRACKET
HOLE MARKS
INSERT THE PULLEY
ASSEMBLY INTO THE
HEADER BRACKET
INSERT THE 2-3/8" CLEVIS PIN
THROUGH THE HEADER BRACKET
AND THE PULLEY ASSEMBLY,
SECURE WITH THE HITCH PIN
(CLEVIS PIN "2D" AND
HITCH PIN "2E" FROM
OPENER PARTS
PACK #2)
MARK A SPOT ON THE
CENTERLINE 1" ABOVE THE
HIGH-RISE POINT OF THE DOOR
MOVE THE DOOR UNTIL THE TOP
PANEL IS AT ITS HIGHEST POSITION
(THE HIGH-RISE POINT)
BOTTOM OF BRACKET
1" ABOVE THE
HIGH-RISE POINT
DOOR
CENTERLINE
A NAIL CAN BE USED TO HOLD
THE BRACKET WHILE MARKING
(NAIL HOLE IS NEXT TO THE TOP
MOUNTING HOLE)
MARK THE CENTER
OF THE TWO
MOUNTING HOLES
USE A 1/2" SOCKET TO ATTACH
THE HEADER BRACKET WITH
TWO 5/16 x 2" LAG SCREWS
(LAG SCREWS "2C" FROM
OPENER PARTS PACK #2)
MARK THE DOOR CENTERLINE
1
MARK ABOVE THE HIGH-RISE POINT
2
ADD A CROSS PIECE IF NECESSARY
3
MARK THE BRACKET HOLES
4
DRILL TWO PILOT HOLES
5
ATTACH THE BRACKET
6
POSITION THE OPENER
7
CONNECT THE RAIL TO THE HEADER BRACKET
8
MMEXT8