User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesRB4011iGS+5HacQ2HnD-IN

Table Of Contents

RB4011iGS+5HacQ2HnD-IN

RB4011iGS+5HacQ2HnD-IN

The device is already configured with basic settings, you can simply plug in your ISP cable and start using the Internet. We recommend you to set up a

password to secure your device.

Setup

Choose your powering solution, please see the section for possibilities.Powering

Connect your Internet cable to port 1, and local network devices to other ports.

Set your computer IP configuration to (DHCP).

automatic

Wireless access point mode is enabled by default.

Connect your direct input power jack if not using POE, to start up the device.

The device will boot up and after a short beep Wireless network will be available for connecting.

Open network connections on your PC, mobile phone, or other device and search for MikroTik wireless network and connect to it.

Once connected to the wireless network, open in your web browser to start configuration, since there is no password by https://192.168.88.1

default, you will be logged in automatically.

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best

performance and stability.

Choose your country, to apply country regulation settings, and set up your password on the screen that loads.

Powering

The power consumption under maximum load can reach 44 W. The device accepts power from the power jack or from the first Ethernet port:

Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC.

First Ethernet port accepts Power over Ethernet 18-57 V DC.

Connecting to a POE Adapter:

Connect the Ethernet cable from the device to the POE port of the POE adapter.

Connect an Ethernet cable from your LAN to the LAN port of the POE adapter, please mind arrows for data and power flow.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Configuration

Once logged in, we recommend clicking the "Check for updates" button in the QuickSet menu, as updating your RouterOS software to the latest version

ensures the best performance and stability. For wireless models, please make sure you have selected the country where the device will be used, to

conform with local regulations.

RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to

the possibilities: . In case an IP connection is not available, the Winbox tool ( ) can be used to connect to the MAC https://mt.lv/help https://mt.lv/winbox

address of the device from the LAN side (all access is blocked from the Internet port by default).

For recovery purposes, it is possible to boot the device for reinstallation, see section .Buttons and jumpers

Mounting

Summary of content (7 pages)

PAGE 1
RB4011iGS+5HacQ2HnD-IN RB4011iGS+5HacQ2HnD-IN The device is already configured with basic settings, you can simply plug in your ISP cable and start using the Internet. We recommend you to set up a password to secure your device. Setup Choose your powering solution, please see the Powering section for possibilities. Connect your Internet cable to port 1, and local network devices to other ports. Set your computer IP configuration to automatic (DHCP). Wireless access point mode is enabled by default.
PAGE 2
It is possible to attach the device to a wall, using the provided screw holes on the back of the unit. The device should be mounted in a way that the cable openings are pointing downward. The device has no protection from water contamination, please ensure the placement of the device in a dry and ventilated environment. We recommend Cat5/6 shielded cables for our devices. Mounting and configuration of this device should be done by a qualified person.
PAGE 3
Use the MikroTik smartphone app to configure your router in the field, or to apply the most basic initial settings for your MikroTik home access point. Notice The Frequency band 5.470-5.725 GHz isn’t allowed for commercial use. In case WLAN devices work with different ranges than the above regulations, then a customized firmware version from the manufacturer/supplier is required to be applied to the end-user equipment and also prevent the end-user from reconfiguration.
PAGE 4
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 5
ES Por la presente, Mikrotīkls SIA declara que el tipo de equipo radioeléctrico RouterBOARD es conforme con la Directiva 2014/53/UE. El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: https://mikrotik.com/products ET Käesolevaga deklareerib Mikrotīkls SIA , et käesolev raadioseadme tüüp RouterBOARD vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: https://mikrotik.
PAGE 6
PT O(a) abaixo assinado(a) Mikrotīkls SIA declara que o presente tipo de equipamento de rádio RouterBOARD está em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: https://mikrotik.com/products RO Prin prezenta, Mikrotīkls SIA declară că tipul de echipamente radio RouterBOARD este în conformitate cu Directiva 2014/53/UE.
PAGE 7
/mt.lv/help-et+_ FI. Käyttöohje: Kytke virtalähde päälle laitteen. Avaa 192.168.88.1 in selaimen määrittää tuotteen. Lisää tietoa {_}{+}https://mt.lv/help-fi+_ FR. Mode d'emploi: Connectez l'adaptateur d'alimentation pour allumer l'appareil. Ouvrez 192.168.88.1 dans un navigateur Web pour configurer le produit. Plus d'informations dans {_}{+}https://mt.lv/help-fr+_ HR. Uputa za uporabu: Priključite napajanje i uključite uređaj. Za konfiguraciju uređaja u pregledniku otvorite 192.168.88.1.