User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesNetBox 5

Table Of Contents

NetBox 5

NetBox 5

RB911G-5HPacD-NB 

Quickstart

Please follow these quick steps to set up your device:

Remove the upper cover (see " ").Removing upper cover

Connect an external antenna to the SMA connector (see " ").Antenna usage

Open the bottom cover (see " ").Opening bottom cover

Connect the device to the included PoE injector with Ethernet cable;

Connect the PoE injector to your Network device with an enabled DHCP server;

Connect the power adapter to the PoE injector;

Default IP: 0.0.0.0, user name: admin and there is no password, use a Web browser and the IP address you have received from your DHCP

server and connect to WebFig;

Once connected, configure the device, so it has an active Internet connection ;https://mt.lv/configuration

Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade

In the "QuickSet, PTP Bridge AP" menu set up the following: Choose your country, to apply country regulation settings;

Set the antenna gain, depending on the antenna used;

Set up your router password in the bottom field.

Powering

The device accepts power in the following ways:

Ethernet port accepts Passive PoE 8-30 V DC .

The power consumption under maximum load can reach 11.5 W.

Connecting to a PoE Adapter:

Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter.

Connect an Ethernet cable from your local network (LAN) to the PoE adapter.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Removing upper cover

This device needs to be upgraded to RouterOS v6.46 or the latest version to ensure compliance with local authority regulations.

It is the end users responsibility to follow local country regulations, including operation within legal frequency channels, output

power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All MikroTik radio devices must be

professionally installed.

Summary of content (10 pages)

PAGE 1
NetBox 5 RB911G-5HPacD-NB This device needs to be upgraded to RouterOS v6.46 or the latest version to ensure compliance with local authority regulations. It is the end users responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All MikroTik radio devices must be professionally installed.
PAGE 2
To remove the upper cover, press both side clips. Pull cover to the side while holding the body. When assembling please not mark on the top cover or reference. Opening bottom cover To open the bottom cover, press clip upwards to release. Pull cover slightly from the device body. Lift it, but do not remove it completely. Expansion slots and ports Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X).
PAGE 3
When mounting, please ensure that the cable feed is pointing downwards. The IP rating scale of this device is IP54. We recommend using Cat6 shielded cables. Warning! This equipment should be installed and operated with a minimum distance of 240 cm between the device and your body. The operation of this equipment in the residential environment could cause radio interference. Mounting and configuration of this device should be done by a qualified person.
PAGE 4
Mounting using DIN rail When mounting on the DIN rail, please find a special bracket in the package and secure it with four screws to the back of the unit. With the attached mounting bracket you will be able to slide the device on the DIN rail. Front status LED behavior RouterOS allows configuring each LED's activity the way that the user wishes. It is possible to configure the LEDs to display wireless strength, blink the LEDs on interface traffic activity and many other options.
PAGE 5
Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds). Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. Useful for RouterBOOT debugging and recovery. Accessories The package includes the following accessories that come with the device: EU/US Switching Power Supply 24 V DC , 0.8 A, 19.2 W.
PAGE 6
Before you work on any MikroTik equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. The installer should be familiar with network structures, terms, and concepts. Use only the power supply and accessories approved by the manufacturer, and which can be found in the original packaging of this product. This equipment is to be installed by trained and qualified personnel, as per these installation instructions.
PAGE 7
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 8
32 dBi Dish Antenna (Model: HDDA5W-32-DP2) The same type of antenna and lower antenna gain than those listed above may also be used according to certification. CE Declaration of Conformity Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039. BG С настоящото Mikrotīkls SIA декларира, че този тип радиосъоръжение RouterBOARD е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://mikrotik.
PAGE 9
IT Il fabbricante, Mikrotīkls SIA , dichiara che il tipo di apparecchiatura radio RouterBOARD è conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformità UE è disponibile al seguente indirizzo Internet: https://mikrotik.com/products IS Hér með lýsir Mikrotīkls SIA því yfir að RouterBOARD er í samræmi við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 2014/53/EU. Fullur texti ESB samræmisyfirlýsingar er að finna á eftirfarandi veffangi: https://mikrotik.
PAGE 10
MPE statement This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 375 cm between the radiator and your body. In RouterOS you must specify your country, to make sure local wireless regulations are observed.