User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesQRT 5

Table Of Contents

QRT 5

QRT 5

Model: RB911G-5HPnD-QRT

Quickstart

Please follow these quick steps to set up your device:

Mount the unit in your desired place, please see paragraph.Mounting

Slide off latch to access Ethernet port. Please see the section.Opening latch

Connect your PoE cable to the Ethernet port, please see the section.Powering

Set your computer IP configuration to automatic (DHCP).

From your PC connect to the wireless network name which starts with "MikroTik".

Once connected to the wireless network, open in your web browser to start configuration, since there is no password by https://192.168.88.1

default, you will be logged in automatically.

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best

performance and stability.

Choose your country, to apply country regulation settings, and set up your password on the screen that loads.

Powering

The device accepts power from the PoE to the Ethernet port:

Passive Power over Ethernet 8-30 V DC .

The power consumption under maximum load can reach 12 W.

Connecting to a POE Adapter:

Connect the Ethernet cable from the device to the POE+DATA port of the POE adapter.

Connect an Ethernet cable from your local network (LAN) to the POE adapter.

Connect the power cord to the adapter, and then plug the power cord into a power outlet.

Configuration

Summary of content (9 pages)

PAGE 1
QRT 5 Model: RB911G-5HPnD-QRT Quickstart Please follow these quick steps to set up your device: Mount the unit in your desired place, please see Mounting paragraph. Slide off latch to access Ethernet port. Please see the Opening latch section. Connect your PoE cable to the Ethernet port, please see the Powering section. Set your computer IP configuration to automatic (DHCP). From your PC connect to the wireless network name which starts with "MikroTik".
PAGE 2
We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and stability. RouterOS includes many configuration options in addition to what is described in this document. We suggest starting here to get yourself accustomed to the possibilities: https://mt.lv/help. In case IP connection is not available, the Winbox tool (https://mt.
PAGE 3
1. 2. 3. 4. Solid Blue – The device is powered on. Solid Green – Connected Ethernet port. Solid Green – User-defined LED. Solid Green – The set of five green LEDs, shows the signal strength. Mounting The device is designed to be used outdoors and mounted on the mast with all needed cables connecting through the latch of the unit. Mounting and configuration of this device should be done by a qualified person. When mounting on the mast, please ensure that the cable feed is pointing downwards.
PAGE 4
Use the mounting bracket (E), and put it on to the back of the antenna. Install with one rubber ring, one washer, and one nut for each of the builtin bolts (in that order).
PAGE 5
Attach the swivel adjuster to the mounting bracket. Use the long bolt in the position (F). Put one regular washer, and one spring washer onto the shorter screws, then put them in positions (G). Do not tighten too much, as you need to adjust the antenna now. Once antenna level and angle are adjusted according to the wireless signal in software, tighten all nuts. Note the degrees of angle for future reference.
PAGE 6
Or Keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall servers (total 15 seconds). Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device. Useful for RouterBOOT debugging and recovery. Accessories Package includes accessories that come with the device: Montage elements: QRT U Bolt, Steel - Zinc plated, DIA 6 mm, U mast clamp, antenna mount.
PAGE 7
Innovation, Science and Economic Development Canada This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 8
FI Mikrotīkls SIA vakuuttaa, että radiolaitetyyppi RouterBOARD on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: https://mikrotik.com/products FR Le soussigné, Mikrotīkls SIA , déclare que l'équipement radioélectrique du type RouterBOARD est conforme à la directive 2014/53/UE. Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante: https://mikrotik.
PAGE 9
WLAN Operating Frequency / Maximum output power Betriebsfrequenz / maximale Ausgangsleistung Fréquence de fonctionnement / puissance de sortie maximale 5470-5725 MHz / 27 dBm Frequenza operativa / massima potenza di uscita Frecuencia de funcionamiento / potencia de salida máxima Рабочая частота / максимальная выходная мощность This MikroTik device meets Maximum TX power limits per ETSI regulations.