User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesmANTBox 52 15s

Table Of Contents

MANTBox 52 15s

10.

11.

12.

13.

14.

15.

MANTBox 52 15s

mANTBox 52 15s

Safety Warnings

Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing

accidents.

Read the installation instructions before connecting the system to the power source.

This equipment is to be installed by trained and qualified personnel, as per these installation instructions. The installer is responsible for obtaining any

required local or national safety inspections of the structural integrity of the installation by the local authority/inspection department.

All installation methods for mounting an access point on any wall surface are subject to the acceptance of local jurisdiction.

The Installation of the equipment must comply with local and national electrical codes.

This unit is intended to be mounted outdoors on a pole. Please read the mounting instructions carefully before beginning installation.

Failure to use the correct hardware and configuration or to follow the correct procedures could result in a hazardous situation to people and damage to the

system.

We cannot guarantee that no accidents or damage will occur due to the improper use of the device. Please use this product with care and operate at your

own risk.

This device needs to be upgraded to RouterOS v6.46 or the latest version to ensure compliance with local authority regulations.

First use

Open cover (see Opening cover).

Connect the Ethernet cable from your PC to the Ethernet port.

Plug the device into the power source (see Powering).

Download the Winbox (see Configuration).

Open and search the MAC address in the Neighbors tab.

Click on the MAC address and connect.

The username is admin and there is no password. The default IP address from the Ethernet port is 192.168.88.1 for configuration if connecting

without WinBox, then set the IP address of your computer to 19.168.88.2.

Update the device to the latest RouterOS version, make sure that the device has an internet connection .https://mt.lv/configuration

Set a Country, to make sure local regulations are observed.

Set the antenna gain, depending on the antenna used.

Set up your password.

To manually update the device, please go to .https://mikrotik.com/download

Choose (ARM) packages for this device and download them to your PC.

Upload downloaded packages to the (Winbox) (Files) menu and reboot the device.

Updating your RouterOS software to the latest version will ensure the best performance, stability, and security updates, .https://mt.lv/upgrade

Powering

The device accepts power in the following ways:

The Ethernet port accepts PoE 12-57 V DC .802.3af/at

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Summary of content (7 pages)

PAGE 1
MANTBox 52 15s mANTBox 52 15s Safety Warnings Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents. Read the installation instructions before connecting the system to the power source. This equipment is to be installed by trained and qualified personnel, as per these installation instructions.
PAGE 2
Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC. The power consumption under maximum load can reach 21 W. Connecting to a PoE Adapter: 1. Connect the Ethernet cable from the device to the PoE+DATA port of the PoE adapter; 2. Connect an Ethernet cable from your local network (LAN) to the PoE adapter; 3. Connect the power cord to the adapter, and then plug the power cord into a power outlet.
PAGE 3
Grounding The installation infrastructure (towers and masts), as well as the router itself, must be properly grounded. The device includes a grounding wire attachment screw behind the case door. Attach your grounding wire to the grounding screw, then attach the other end of the grounding wire to the grounded mast. This is to substantially reduce the risk of ESD and lightning damage. The device includes a grounding connection (marked ).
PAGE 4
Accessories The package includes the following accessories that come with the device: Switching Power Supply DC 24 V; Hose Clamp, 35-70 mm; Fastening set K-41; Gigabit POE injector cable with shielded connector; Mounting bracket. Please visit wiki pages for the MikroTik SFP module compatibility table: https://wiki.mikrotik.com/wiki/MikroTik_SFP_module_compatibility_table Operating system support The device supports RouterOS software version 6.46.
PAGE 5
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
PAGE 6
FR Le soussigné, Mikrotīkls SIA , déclare que l'équipement radioélectrique du type RBD22UGS-5HPacD2HnD-15S est conforme à la directive 2014/53 /UE. Le texte complet de la déclaration UE de conformité est disponible à l'adresse internet suivante: https://mikrotik.com/products HR Mikrotīkls SIA ovime izjavljuje da je radijska oprema tipa RBD22UGS-5HPacD2HnD-15S u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedećoj internetskoj adresi: https://mikrotik.
PAGE 7
This MikroTik device meets Maximum WLAN and LTE transmit power limits per ETSI regulations. For more detailed information see Declaration of Conformity above / Dieses MikroTik-Gerät erfüllt die maximalen WLAN- und LTE-Sendeleistung Grenzwerte gemäß ETSI-Bestimmungen. Weitere Informationen finden Sie oben unter Konformitätserklärung / Cet appareil MikroTik respecte les limites maximales de puissance de transmission WLAN et LTE conformément aux réglementations ETSI.