User Manual

ManualsBrandsMikroTik ManualsComputers & AccessorieshAP ac²

Table Of Contents

hAP ac²

hAP ac²

The hAP is a simple home wireless access point. It is already configured, you can simply plug in your ISP cable and start using wireless internet. We

recommend you to set up a password to secure your device.

Powering

The device accepts power from the power jack or from the first Ethernet port (Passive PoE):

direct-input power jack (5.5mm outside and 2mm inside, female, pin positive plug) accepts 12-30 V DC

first Ethernet port accepts passive Power over Ethernet accepts 18-28 V DC (compensate for the loss on cable, so more than 12V recommended)

The power consumption under maximum load can reach 15 W.

Setup

Connect your internet cable to the first port, and, if you have wired devices, connect them to the other ports

Set your computer IP configuration to automatic (DHCP).

From your PC or smartphone, connect to the wireless network name which starts with "MikroTik".

Once connected to the wireless network, open in your web browser to start configuration since there is no password by https://192.168.88.1 ,

default, you will be logged in automatically. Set up your password in the screen that loads. Please also specify your country, to make sure local

regulations are observed.

Configuration

We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and

stability. RouterOS includes many configuration options in addition to what is described in this document. We suggest to start here to get yourself

accustomed to the possibilities: . In case IP connection is not available, the Winbox tool ( ) can be used to connect to https://mt.lv/help https://mt.lv/winbox

the MAC address of the device from the LAN side (all access is blocked from the internet port by default). For recovery purposes, it is possible to boot the

device from the network, see section .Buttons and jumpers

Extension slots and ports

The Ethernet ports are connected through a switch chip, can be configured individually and support automatic cross/straight cable correction

(Auto MDI/X), so you can use either straight or cross-over cables for connecting to other network devices.

The integrated wireless module which supports AP/CPE/P2P/Repeater modes.

Buttons and jumpers

RouterBOOT reset button has the following functions:

Hold the button before powering on the device, and at power-up, the button will force load the backup boot loader. Continue holding the button for

the other two functions of this button.

Summary of content (6 pages)

PAGE 1
hAP ac² hAP ac² The hAP is a simple home wireless access point. It is already configured, you can simply plug in your ISP cable and start using wireless internet. We recommend you to set up a password to secure your device. Powering The device accepts power from the power jack or from the first Ethernet port (Passive PoE): direct-input power jack (5.
PAGE 2
Release the button when green LED starts flashing, to reset RouterOS configuration. To not load the backup boot loader, you can start holding the button after power is already applied. Release the button after LED is no longer flashing (~20 seconds) to cause the device to look for Netinstall servers (required for reinstalling RouterOS over the network). Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the device.
PAGE 3
С настоящото Mikrotīkls SIA декларира, че този тип радиосъоръжение RouterBOARD е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://mikrotik.com/products CS Tímto Mikrotīkls SIA prohlašuje, že typ rádiového zařízení RouterBOARD je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: https://mikrotik.
PAGE 4
LT Aš, Mikrotīkls SIA , patvirtinu, kad radijo įrenginių tipas RouterBOARD atitinka Direktyvą 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas šiuo interneto adresu: https://mikrotik.com/products LV Ar šo Mikrotīkls SIA deklarē, ka radioiekārta RouterBOARD atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: https://mikrotik.
PAGE 5
150-5250 MHz 26 - 48 23 dBm Restricted to indoor use only* 5250-5350 MHz 52 - 64 20 dBm Restricted to indoor use only* 5470-5725 MHz 100 - 140 27 dBm Without any restriction to use in all EU Member States * It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed! Note.
PAGE 6
https://mt.lv/help+_ RU. Руководство по эксплуатации: подключите адаптер питания чтобы включить устройство. Откройте 192.168.88.1 в своем веб-браузере для конфигурации. Дополнительная информация: {_}{+}https://mt.lv/hel+_ p CN. 说明书。连接电源适配器以打开设备。在Web浏览器中打开192.168.88.1进行配置。有关https://mt.