User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesLHG XL HP5

Table Of Contents

LHG XL HP5

LHG XL HP5

RBLHG-5HPnD-XL LHG XL HP5

Assembly

Attach the two legs to the LHG case, then snap the assembled LHG unit to the grid in the appropriate locations. Fix the legs in place with two

self thread screws (Included, use Phillips screwdriver PH2). Attach the L shaped mount to the dish using the included screws. Use the U bolt, to

fix the unit to a pole/mast. More detailed instructions available on the product page on .https://mikrotik.com/products/

Connecting

Open the Ethernet door to connect your PC or LAN cable to the Ethernet port, connect the other end of the Ethernet cable to a PoE injector;

Set LAN computer IP configuration to (DHCP);

automatic

Default The IP address of the unit is 192.168.88.1, open this address in your web browser to start the configuration. The username is and admin

there is no password;

In case the IP address is not available, download WinBox configuration tool , andconnect through MAC address;https://mt.lv/winbox

Once connected configure the device, so it has an active Internet connection ;https://mt.lv/configuration

Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade

Choose your country, to apply country regulation settings;

Secure your device and set a strong password.

Powering

The device accepts powering only from Passive PoE injectors.

Extension slots and ports

One Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X), so you can use either straight or cross-over cables for

connecting to other network devices.

One integrated wireless device with a built-in grid antenna.

Buttons and jumpers

The reset button has three functions:

• Hold this button during boot time until LED light starts flashing, release the button to reset RouterOS configuration (total 5 seconds).

• Keep holding for 5 more seconds, LED turns solid, release now to turn on CAPs mode (total 10 seconds).

• Or keep holding the button for 5 more seconds until LED turns off, then release it to make the RouterBOARD look for Netinstall

servers (total 15 seconds).

Regardless of the above option used, the system will load the backup RouterBOOT loader if the button is pressed before power is applied to the

device. Useful for RouterBOOT debugging and recovery.

Operating system support

Summary of content (5 pages)

PAGE 1
LHG XL HP5 RBLHG-5HPnD-XL LHG XL HP5 Assembly Attach the two legs to the LHG case, then snap the assembled LHG unit to the grid in the appropriate locations. Fix the legs in place with two self thread screws (Included, use Phillips screwdriver PH2). Attach the L shaped mount to the dish using the included screws. Use the U bolt, to fix the unit to a pole/mast. More detailed instructions available on the product page on https://mikrotik.com/products/.
PAGE 2
The device supports RouterOS software with the version number at or above what is indicated in the RouterOS menu /system resource. Other operating systems have not been tested. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 3
EL Με την παρούσα ο/η Mikrotīkls SIA , δηλώνει ότι ο ραδιοεξοπλισμός RouterBOARD πληροί την οδηγία 2014/53/ΕΕ. Το πλήρες κείμενο της δήλωσης συμμόρφωσης ΕΕ διατίθεται στην ακόλουθη ιστοσελίδα στο διαδίκτυο: https://mikrotik.com/products EN Hereby, Mikrotīkls SIA declares that the radio equipment type RouterBOARD is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://mikrotik.
PAGE 4
NO Mikrotīkls SIA erklærer herved at utstyret RouterBOARD er i samsvar med de grunnleggende krav og øvrige relevante krav i direktiv 2014/53/EU. Den fulle teksten til EU-samsvarserklæringen er tilgjengelig på følgende internettadresse: https://mikrotik.com/products PL Mikrotīkls SIA niniejszym oświadcza, że typ urządzenia radiowego RouterBOARD jest zgodny z dyrektywą 2014/53/UE. Pełny tekst deklaracji zgodności UE jest dostępny pod następującym adresem internetowym: https://mikrotik.
PAGE 5
EL. εγχειρίδιο οδηγιών: Συνδέστε τον προσαρμογέα τροφοδοσίας για να ενεργοποιήσετε τη μονάδα. Ανοίξτε 192.168.88.1 σε ένα πρόγραμμα περιήγησης στο Web για να διαμορφώσετε το προϊόν. Περισσότερες πληροφορίες στο {+}https://mt.lv/help+ EN. Instruction manual: Connect the power adapter to turn on the device. Open 192.168.88.1 in your web browser, to configure it. More information on {_} {+}https://mt.lv/help+_ ES. Manual de instrucciones: Conecte el adaptador de alimentación para encender la unidad. Abra 192.