User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesLtAP LR8 LTE kit

Table Of Contents

LtAP LR8 LTE kit

LtAP LR8 LTE kit

LtAP LR8 LTE kit (RBLtAP-2HnD&R11e-LTE&LR8)

Quickstart

Please follow these quick steps to set up your device:

Open the bottom lid;

Insert the SIM card into the SIM 2 slot (middle);

Connect the device to the power source;

Connect with your computer to the MikroTik wireless network;

Open in your web browser to start the configuration;https://192.168.88.1

The user name: and there is no password set, by default;

admin

Once connected, in the QuickSet LTE AP menu, enter your PIN code ;https://mt.lv/configuration

Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade

Connect again and in the menu set your wireless network password;

QuickSet LTE AP

Choose your country on the left side of the screen, to apply country regulation settings;

Secure your device and set a strong password.

Find your on the label within the product and register it in your Network Server.

LR Gateway ID



Extension slots and ports

Built-in 2 GHz wireless access point module, AP/station/bridge/p2p modes are supported. Onboard PIF antennas built-in, as well as MMCX

connectors for external antennas (software selectable).

Two miniPCIe slots and three SIM slots.

Built-in GPS module with an external SMA connector.

Gigabit Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight or crossover cable can be used for

connecting to other network devices. The Ethernet port accepts 12-30 V DC powering from a passive PoE injector.

One DB9 RS232 serial port for serial console access. Configured as 115200 bit/s, 8 data bits, 1 stop bit, no parity.

One USB 2.0 port.

R11e-LR8, miniPCIe card with external SMA connector.

Summary of content (8 pages)

PAGE 1
LtAP LR8 LTE kit LtAP LR8 LTE kit (RBLtAP-2HnD&R11e-LTE&LR8) Quickstart Please follow these quick steps to set up your device: Open the bottom lid; Insert the SIM card into the SIM 2 slot (middle); Connect the device to the power source; Connect with your computer to the MikroTik wireless network; Open https://192.168.88.
PAGE 2
Mounting 1. It is possible to attach the device to a wall, using the provided four screws and designed four holes on the unit. 2. The ports are protected with a small door, that is held in place with two screws. Remove to access Ethernet ports, antenna connector, SIM slots, etc. 3. The door has cut-out places for all available ports, so you can guide through all necessary cables, but please only break out the openings that you will use. 4.
PAGE 3
Supports - GPS, GLONASS, BeiDou, Galileo). Make sure that the GPS package is installed on your device. Check by following command /system package print. If not installed please download extra packages at our download page accordingly to your RouterOS version and install the GPS package by dragging it to the Files menu. Enable GPS and start working: Enabling - /system gps set enable=yes; Setting antenna to external - /system gps set gps-antenna-select=external; Checking configuration - /system gps print.
PAGE 4
1. 2. 3. 4. Solid Blue – the device is powered on. Solid Green – user-defined LED, can be configured in system settings. Solid Green – state of GPS module. Solid Green– the set of five green LED, shows the signal strength of the cellular network. miniPCIe slot SIM card connectivity MiniPCIe 1 LR (top slot) supports PCIe and USB 2.0 cards but is shared with the USB 2.0 type A port (can use either the USB port or miniPCIe slot at the same time). It can be used only for SIM slot #1.
PAGE 5
After you have reinserted the device into the case and secured it with the screws that were removed earlier, slide in the SIM cards from your mobile operator into the SIM slots, with the chips facing as shown on the port label. The slot accepts miniSIM (2FF). SIM slots 2 and 3 apply to the bottom miniPCIe slot and can be switched in RouterOS "/system routerboard sim" menu.
PAGE 6
Safety Warnings Before you work on any equipment, be aware of the hazards involved with electrical circuitry, and be familiar with standard practices for preventing accidents. Read the installation instructions before connecting the system to the power source. This equipment is to be installed by trained and qualified personnel, as per these installation instructions.
PAGE 7
ET Käesolevaga deklareerib Mikrotīkls SIA, et käesolev raadioseadme tüüp RouterBOARD vastab direktiivi 2014/53/EL nõuetele. ELi vastavusdeklaratsiooni täielik tekst on kättesaadav järgmisel internetiaadressil: https://mikrotik.com/products FI Mikrotīkls SIA vakuuttaa, että radiolaitetyyppi RouterBOARD on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuksen täysimittainen teksti on saatavilla seuraavassa internetosoitteessa: https://mikrotik.
PAGE 8
This MikroTik device meets Maximum WLAN and LTE transmit power limits per ETSI regulations. For more detailed information see Declaration of Conformity above / Dieses MikroTik-Gerät erfüllt die maximalen WLAN- und LTE-Sendeleistung Grenzwerte gemäß ETSI-Bestimmungen. Weitere Informationen finden Sie oben unter Konformitätserklärung / Cet appareil MikroTik respecte les limites maximales de puissance de transmission WLAN et LTE conformément aux réglementations ETSI.