User Manual

ManualsBrandsMikroTik Manuals60 GHz productswAP 60G AP

Table Of Contents

wAP 60G series

wAP 60G series
Wireless Wire RBwAPG-60adkit
wAP 60G RBwAPG-60ad
wAP 60G AP RBwAPG-60ad-A
wAP 60Gx3 AP RBwAPG-60ad-SA
wAP60G devices work in the 60GHz wireless spectrum, the operating temperature of these devices is from -40°C up to +70°C. The devices have a one-
gigabit ethernet port and can be powered from a power jack or from ethernet. Devices can be securely mounted on a wall, ceiling, or on a pole/mast.
Quick Start
Connect the device to the included PoE injector with Ethernet cable to the data+power end;
Connect the data end of the PoE injector into the computer;
Connect the power adapter to the PoE injector;
Download WinBox configuration tool ;https://mt.lv/winbox
Default IP: 192.168.88.1, user name: and there is no password, for the paired models, please find the password on the sticker;
admin
Set an IP address of your computer to 192.168.88.2;
In case the IP connection is not available, please use the Neighbors tab and connect through MAC address;
Once connected configure the device, so it has an active Internet connection ;https://mt.lv/configuration
Upgrade the RouterOS software to the latest version ;https://mt.lv/upgrade
Choose your country, to apply country regulation settings;
Secure your device and set a strong password;
For more configuration information, please visit ;https://wiki.mikrotik.com/wiki/Manual:Interface/W60G
wAP60G APunits come pre-configured with WISP Bridgedefault configuration;
Wireless Wire and wAP60Gunits come pre-configured with PTP Bridge default configuration;
Wireless Wire devices have already, randomly generated, matching SSID, and Wireless passwords.
Powering
The devices accept powering both from a power adapter, and through the ethernet port:
Direct-input power jack (5.5 mm outside and 2 mm inside, female, pin positive plug) accepts 12-57 V DC.
Ethernet port accepts PoE input 12-57 V DC (passive and 802.3af/at).
A power adapter and a passive PoE injector are included in the box. If using the PoE injector, make sure to use the "Power + Data" connector to connect 
to the wAP60G device and the "Data" connector to your router or switch.
Configuration and connecting
Full RouterOS documentation is located here:  . Specific wAP 60G configuration can be foundhttps://mt.lv/help https://wiki.mikrotik.com/wiki/Manual:
Interface/W60G
Access the device by connecting to the Ethernet port and then use the MikroTik Winbox utility for connection. 
For recovery purposes, it is possible to boot the device from the network, see section  .Buttons and jumpers
In case the IP connection is not available, the Winbox utility can also be used to connect to the MAC address of the device.
Mounting

Summary of content (8 pages)

PAGE 1
wAP 60G series Wireless Wire RBwAPG-60adkit wAP 60G RBwAPG-60ad wAP 60G AP RBwAPG-60ad-A wAP 60Gx3 AP RBwAPG-60ad-SA wAP60G devices work in the 60GHz wireless spectrum, the operating temperature of these devices is from -40°C up to +70°C. The devices have a onegigabit ethernet port and can be powered from a power jack or from ethernet. Devices can be securely mounted on a wall, ceiling, or on a pole/mast.
PAGE 2
Mounting on the mast or pole: * It's recommended to use electrical tape to increase friction between materials. 1. 2. 3. 4. 5. 6. Mount plastic tie straps to steel brackets guiding them through holes. Mount bracket to the device. Secure them with a screw. Mount and align the device on the pole or mast. Guide Ethernet cable through the opening and connect to the Ethernet port. Close bottom latch and secure with a screw.
PAGE 3
It's recommended to secure an Ethernet cable to the pole using zip ties. With the distance from the device approximately 30 cm. Mounting unit on the wall: 1. Use included a template to mark spots for drilling holes. And if needed for Ethernet cable. Align accordingly, it will depend on how the device will be mounted finally. 2. Insert dowels if needed, depends on wall structure and material. 3. Place included a steel bracket on the wall. 4. Use screws to secure it in place. 5.
PAGE 4
Avoid mounting the device on the low ground spot, as you won't be able to attach and close the bottom latch. Mounting on the ceiling: A Special bracket is included in the package to mount on the drop ceiling. As it consists of two parts, to be attached on both sides of the ceiling tile. 1. Use the template to mark spots for holes. 2. Place both mounting brackets on the spot. 3. Secure them together using screws. Continue assembling in the same manner if mounting on the wall. 1. 2. 3. 4.
PAGE 5
Pull the cover in the opposite direction from the device to remove it. Reassemble. Buttons and jumpers The routerBOOT reset button has the following functions. Press the button and apply the power, then: Release the button when the green LED starts flashing, to reset RouterOS configuration to defaults. Release the button when the LED turns solid green to clear all configuration and defaults.
PAGE 6
IT LV LT PT RO SK LU MT NL PL SI ES UK SE Federal Communication Commission Interference Statement Model FCC ID RBwAPG-60adkit TV7WAPG60AD RBwAPG-60ad TV7WAPG60AD RBwAPG-60ad-A TV7WAPG60AD RBwAPG-60ad-SA TV7WAPG60ADM This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
PAGE 7
Cet appareil ne doit pas être utilisé sur un avion, sauf dans les conditions énumérées ISED RSS-210 Annex J.1. CE Declaration of Conformity BG С настоящото Mikrotīkls SIA декларира, че този тип радиосъоръжение RouterBOARD е в съответствие с Директива 2014/53/ЕС. Цялостният текст на ЕС декларацията за съответствие може да се намери на следния интернет адрес: https://mikrotik.com/products CS Tímto Mikrotīkls SIA prohlašuje, že typ rádiového zařízení RouterBOARD je v souladu se směrnicí 2014/53/EU.
PAGE 8
PT O(a) abaixo assinado(a) Mikrotīkls SIA declara que o presente tipo de equipamento de rádio RouterBOARD está em conformidade com a Diretiva 2014/53/UE. O texto integral da declaração de conformidade está disponível no seguinte endereço de Internet: https://mikrotik.com/products RO Prin prezenta, Mikrotīkls SIA declară că tipul de echipamente radio RouterBOARD este în conformitate cu Directiva 2014/53/UE.