User Manual

ManualsBrandsMikroTik ManualsComputers & AccessorieswAP LTE kit US

Table Of Contents

wAP kit-series

wAP kit-series

This manual is for wAP kit series models:

wAP LTE kit

wAP LTE kit US

wAP 4G kit

This device needs to be upgraded to RouterOS v6.44.6 or the latest version to ensure compliance with local authority regulations.

Note. The information contained here is subject to change. Please visit the product page on

www.mikrotik.com for the most up to date version of this

document.

Quickstart

Use a Phillips head screwdriver to loosen the screw, which secures the bottom lid (see ).Bottom Lid

Insert the SIM card.

Choose your powering solution, please see the section for possibilities.Powering

Connect the Ethernet cable to the PoE and connect the other end of the Ethernet cable to this MikroTik router. Plug the provided power supply

into the PoE injector.

Wireless AP mode is enabled by default, you can connect from your computer to the SSID that begins with "MikroTik". The configuration interface

is available via a web browser. The address is .https://192.168.88.1

Connect to the wireless network, open in your web browser to start the configuration.https://192.168.88.1

User name: a and there is no password by default you will be logged in automatically to the Quick Set screen.

dmin

Click the "Check for updates" button on the right side and updating your RouterOS software to the latest version to ensure the best performance

and stability. Must have a valid SIM card inserted.

To personalize your wireless network, SSID can be changed in the fields "Network Name";

Choose your country on the left side of the screen in the field "Country", to apply country regulation settings.

Set up your wireless network password in the field "WiFi Password" the password must be at least eight symbols.

It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling

requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed.

Summary of content (12 pages)

PAGE 1
wAP kit-series This manual is for wAP kit series models: wAP LTE kit wAP LTE kit US wAP 4G kit This device needs to be upgraded to RouterOS v6.44.6 or the latest version to ensure compliance with local authority regulations. It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. All Mikrotik radio devices must be professionally installed. Note.
PAGE 2
Set up your router password in the bottom field "Password" to the right and repeat it in the field "Confirm Password", it will be used to login next time. Click on the "Apply Configuration" to save changes. To manually update the device if no Internet connection is available. Download the latest RouterOS software from https://mikrotik.com/download. Choose MIPSBE packages, and save them to your PC. Connect again and in Files menu upload downloaded packages. Restart the device.
PAGE 3
The automotive connector can be used to power the device from regular 12/24 V connections in automobiles and buses. The plug has four pins: bottom left (black) is the ground, bottom right is power in (red). The upper two are reserved for future use. Maximum power consumption at 24 V is 6 W without miniPCIe, and 8 W with a full load on the miniPCIe card.
PAGE 4
Mounting unit on the wall: 1. Use included a template to mark spots for drilling holes. And if needed for Ethernet cable. Align accordingly, it will depend on how the device will be mounted finally. 2. Insert dowels if needed, depends on wall structure and material. 3. Place included a steel bracket on the wall. 4. Use screws to secure it in the place. 5. Extend your Ethernet cable through the opening and connect to the Ethernet port. 6. Mount the device on the steel bracket 7.
PAGE 5
Avoid mounting the device on the low ground spot, as you won't be able to attach and close the bottom latch. Mounting on the ceiling: A Special bracket is included in the package to mount on the drop ceiling. As it consists of two parts, to be attached on both sides of the ceiling tile. 1. Use the template to mark spots for holes. 2. Place both mounting brackets on the spot. 3. Secure them together using screws. Continue assembling in the same manner if mounting on the wall. 1. 2. 3. 4.
PAGE 6
Pull the cover in the opposite direction from the device to remove it. Reassemble. Expansion slots and ports Built-in 2 GHz wireless access point module, AP/station/bridge/p2p modes are supported. One 10/100 Ethernet port, supporting automatic cross/straight cable correction (Auto MDI/X). Either straight or crossover cable can be used for connecting to other network devices. The ethernet port accepts 9-30 V DC powering from a passive PoE injector.
PAGE 7
Configuration We recommend clicking the "Check for updates" button and updating your RouterOS software to the latest version to ensure the best performance and stability. RouterOS includes many configuration options in addition to what is described in this document. We suggest visiting the RouterOS documentation page to get yourself accustomed to the possibilities: https://mt.lv/help . In case IP connection is not available, the Winbox tool (https://mt.
PAGE 8
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
PAGE 9
CS Tímto Mikrotīkls SIA prohlašuje, že typ rádiového zařízení RouterBOARD je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: https://mikrotik.com/products DA Hermed erklærer Mikrotīkls SIA , at radioudstyrstypen RouterBOARD er i overensstemmelse med direktiv 2014/53/EU. EUoverensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: https://mikrotik.
PAGE 10
LV Ar šo Mikrotīkls SIA deklarē, ka radioiekārta RouterBOARD atbilst Direktīvai 2014/53/ES. Pilns ES atbilstības deklarācijas teksts ir pieejams šādā interneta vietnē: https://mikrotik.com/products MT B'dan, Mikrotīkls SIA , niddikjara li dan it-tip ta' tagħmir tar-radju RouterBOARD huwa konformi mad-Direttiva 2014/53/UE. It-test kollu taddikjarazzjoni ta' konformità tal-UE huwa disponibbli f'dan l-indirizz tal-Internet li ġej: https://mikrotik.
PAGE 11
5150-5250 MHz 26 - 48 23 dBm Restricted to indoor use only* 5250-5350 MHz 52 - 64 20 dBm Restricted to indoor use only* 5470-5725 MHz 100 - 140 27 dBm Without any restriction to use in all EU Member States * It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
PAGE 12
NO. Bruksanvisningen: Koble strømadapteren for å slå på enheten. Åpne 192.168.88.1 i en nettleser for å konfigurere produktet. Mer informasjon på {+}htt ps://mt.lv/help-no+ RU. Руководство по эксплуатации: подключите адаптер питания чтобы включить устройство. Откройте 192.168.88.1 в своем веб-браузере для конфигурации. Дополнительная информация https://mt.lv/help-ru CN. 说明书。连接电源适配器以打开设备。在Web浏览器中打开192.168.88.1进行配置。有关{+}https://mt.