User Manual

ManualsBrandsMikroTik ManualsComputers & AccessoriesTG-BT5-OUT

Table Of Contents

TG-BT5-OUT

TG-BT5-OUT

TG-BT5-OUT are ready to use Bluetooth Tag with a preinstalled battery. The software manual you can find under each product in the Support and

Downloads sections https://mikrotik.com/products

Outdoor Water Proof IP69k - TG-BT5-OUT

Completely sealed and cast IP69k.

Temperature range -30..+85°C.

Shock absorbing case.

Built-in 550mAh LiMnO2 battery.

Suitable for strapping.

Built-in temperature sensor.

Built-in accelerometer.

Magnet activation.

NFC [Serial number].

CryptoAuthentication [ATECC608A].

Dimensions 38x32x15mm.

BLE 5.2 with .Silabs BG22

Overview

TG-BT5-OUT is a new addition to our MikroTik equipment. It is a Bluetooth tag (a very small gadget) that can be attached to other equipment or other

belonging. Bluetooth tags play a big role in IoT topologies, where Bluetooth is used to broadcast the data over short distances. Once installed and

configured, the tag will broadcast advertising packets in (default packet format) to the gateway (for example, iBeacon, Eddystone, or Mikrotik telemetry KN

). Gateway, on the other hand, pushes the advertising packet payload to the remote server utilizing or HTTP protocols.OT MQTT

Tag modes

When the product arrives from manufacturing it is set into factory sleep mode. In this mode, all components are shut-down as much as possible and MCU

is put into the deepest sleep state. The current draw is reduced to a minimum, so this is the preferred mode to use when the tag is stored and/or not in use.

To exit this mode put a magnet to the tag's edge (where the switch icon is) and hold it for 3-10 seconds until LED turns off. After that, the tags exits sleep

mode and enters advertising mode.

In the Advertising mode, the tag will broadcast Bluetooth advertising packets. By default, MikroTik's advertisement packets are sent once every 5 seconds.

This can be changed in the Configuration mode.

Configuration mode can be entered only from advertising mode by applying a magnet to the same switch icon as in the exiting factory sleep procedure.

After applying a magnet for 5-10 seconds LED will turn off and the tag enters configuration mode. If you apply a magnet for longer than 15 seconds or

won't connect to the tag with the configuration app, it will go back into advertising mode.

When the device wakes from the factory sleep for the first time, it has this default configuration:

Configuration parameter Setting/value

Advertising packet format MikroTik

Advertising interval 5.0 seconds

Angle Threshold/Tilt trigger 60°

Freefall Threshold/Accelerometer trigger 156.25 mg

Wakeup Threshold/Wakeup trigger 1.0 mg

Bandwith Filter 0.8 Hz

Low noise filter disabled

Tx Power 4 dBm

Summary of content (7 pages)

PAGE 1
TG-BT5-OUT TG-BT5-OUT are ready to use Bluetooth Tag with a preinstalled battery. The software manual you can find under each product in the Support and Downloads sections https://mikrotik.com/products Outdoor Water Proof IP69k - TG-BT5-OUT Completely sealed and cast IP69k. Temperature range -30..+85°C. Shock absorbing case. Built-in 550mAh LiMnO2 battery. Suitable for strapping. Built-in temperature sensor. Built-in accelerometer. Magnet activation. NFC [Serial number]. CryptoAuthentication [ATECC608A].
PAGE 2
The magnet is used on the reed switch to change the tag's operating modes as described above. As soon as the magnet is detected (the reed switch is activated), the LED will start flashing for the next 5 seconds (first 5 seconds) and, then, stop. It can help you identify that 5 seconds have passed and that you can remove the magnet to enter configuration mode. Initial steps Install the "MikroTik Beacon Manager" application and run the app. For Android devices, you can find it following the link.
PAGE 3
To "wake up" the tag from the factory sleep mode, the reed switch should be activated for 3-10 seconds. As soon as the device "wakes up", it will show up in the "MikroTik Beacon Manager" list.
PAGE 4
After a short wind up time, the device should be ready to be configured: The app will show general information about the tag in the "Status" tab and will allow you to alter the tag's setting using the "Settings" tab (as shown in the screenshot above).
PAGE 5
Useful links You can find the guide on how to configure the tag using the Android app following the link: MikroTik Beacon Manager for Android devices You can find more information about the tag's advertisement formats following the link: MikroTik Tag advertisement formats Federal Communication Commission Interference Statement Model FCC ID TG-BT5-OUT TV7-TB5O This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
PAGE 6
CS Tímto Mikrotīkls SIA prohlašuje, že typ rádiového zařízení TG-BT5-OUT je v souladu se směrnicí 2014/53/EU. Úplné znění EU prohlášení o shodě je k dispozici na této internetové adrese: https://mikrotik.com/products DA Hermed erklærer Mikrotīkls SIA, at radioudstyrstypen TG-BT5-OUT er i overensstemmelse med direktiv 2014/53/EU. EUoverensstemmelseserklæringens fulde tekst kan findes på følgende internetadresse: https://mikrotik.
PAGE 7
SV Härmed försäkrar Mikrotīkls SIA att denna typ av radioutrustning TG-BT5-OUT överensstämmer med direktiv 2014/53/EU. Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: https://mikrotik.com/products WLAN / Bluetooth / LTE (EN) Operating Frequency / Maximum output power (DE) Betriebsfrequenz / maximale Ausgangsleistung (FR) Fréquence de fonctionnement / puissance de sortie maximale Bluetooth 2400-2483.5 MHz / 3.