MIL-S500 User’s Guide 5-Port 10/100 Switch
© COPYRIGHT 2004 ALL RIGHTS RESERVED. First Edition. Printed in Taiwan. All trademarks are the properties of their respective owners. No portion of this document may be reproduced, altered, adapted or translated without the prior written approval. DOCUMENT WARRANTY The information in this document is subject to change without notice. We make no warranty of any kind regarding this material, including, but not limited to, the implied warranties or merchantability and fitness for a particular purpose.
To Contact MiLAN Technology For prompt response when calling for service information, have the following information ready: Product serial number and revision. Date of purchase and Vendor or place of purchase. You can reach MiLAN Technology technical support at: E-mail: support@milan.com Telephone: +1.408.744.2751 Fax: +1.408.744.2771 http://www.milan.com info@milan.comT ©Copyright 2004 MiLAN Technology MiLAN Technology 1329 Moffett Park Dr Sunnyvale, CA 94089-1138 United States of America Telephone: +1.
MIL-S500 Switch User’s Guide Introduction The MIL-S500 Switch provides wire-speed, Fast Ethernet switching function that allows high-performance, low cost connections to full-duplex, half-duplex, 10Mbps and 100Mbps Ethernet network. The MIL-S500 switch provides five auto-sensing 10/100Mbps RJ-45 ports that automatically detects the speed of the device that is plugged into it.
MDI/MDIX Auto-recognition (No cross over cable required) Magnets provide easy installation in modular office Package Contents Your package contents should include the following: MIL-S500 Switch Four rubber feet with adhesive pads Two Magnets User’s Guide Figure 2.
If any of these pieces are found missing or damaged, please contact your local dealer or reseller for replacement. Hardware Description The Front Panel The front panel consists of LED Indicators. Figure 3. Front view of MIL-S500 Switch LEDs Per Device Per Port Power 100Mbps ( Link on 100Mbps ) LINK/ACT ( Link/Activity ) The Rear Panel The rear panel of the MIL-S500 Switch has a DC power connector and 5 auto-sensing ports.
Figure 4. Rear panel view of the MIL-S500 switch Auto-sensing ports for speed and Duplex Five Auto-sensing RJ-45 ports for 10Base-T or 100Base-TX connections. DC Power Connector Plug this connector female end into this device, and the male into a power outlet. Supported input voltages 9 VDC at 700 mA. Auto-sensing for MDI/MDIX No need for crossover 5 LED-Indicators Figure 5. Front panel view of LED indications The Table lists the LEDs available and their respective function.
On LINK/ACT Blinking Off Green The port is successfully connecting with the device. The port is receiving or transmitting data. The port does not link successfully with the device. Installation Apply self-adherent rubber feet to the bottom of the Switch near each of the four corners. 6 See Figure 6. If applying Switch to metal surface, install magnets as shown in Figure 6. Switch may then be installed on a metal surface. Plug in power adapter.
The Switch can be easily monitored through panel indicators that assist in the identification of problems. This section describes common problems you may encounter and where you can find possible solutions. Power If the power indicator does not turn on when the power cord is plugged in, you may have a problem with the power outlet, or power cord. However, if it powers off after running for a while, check for loose power connections, power losses or surges at the power outlet.
Performance Specification Transmission Method Store and forward MAC address table Maximum Forwarding Rate(64byte packets) Maximum Filtering Rate(64byte packets) 1K-entry MAC address table 14,880 pps /10 BASE-T 148,800 pps /100BASE-TX 14,880 pps /10BASE-T 148,800 pps/100BASE-TX Flow control Pause frame (Full-duplex) Back-pressure (Half-duplex) Duplex mode Supports both half-duplex and full-duplex mode Physical & Environmental Specification Power Supply Dimensions Temperature Humidity EMI Safety Exte
P/N 90000200 Rev C 12
