MIL-S800 User’s Guide 8 port 10/100BASE-TX Switch
Regulatory Approval - FCC Class A - UL 1950 - CSA C22.2 No. 950 - EN60950 - CE - EN55022 Class B - EN55024 Canadian EMI Notice This Class A digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numerique de la classe A respecte toutes les exigences du Reglement sur le materiel brouilleur du Canada.
Table of Contents Chapter 1. Introduction 1-1 General Description……………………………………. 1-2 Key Features……………………………………………… 1-3 Package Contents……………………………………… 1-4 Hardware Description………………………………….. Pg 1 Pg. 1 Pg. 1 Pg. 2 Pg. 3 Chapter 2. Hardware Installation 2-1 Quick Installation………………………………………... 2-2 LED Descriptions…………………………………………. Pg 4 Pg. 4 Pg. 5 Chapter 3. Network Application 3-1 Stand Alone……………………………………………… 3-2 Uplink Multiple Hubs……………………………………. Pg 6 Pg. 6 Pg. 6 Chapter 4.
Chapter 1 Introduction 1-1 General Description The MIL-S800 switch provides eight auto-sensing 10/100Mbps RJ45 Ethernet ports. This high performance, low cost, wire speed desktop switch is ideal for any network where 8 ports are needed, for a solution to an enterprise need or for a home network. The MIL-S800 can be mounted on the wall with keyholes in the chassis or magnetically attached to any metal surface. 1-2 Key Features • • • • • • • • • • • • Compliant with IEEE 802.3, 802.3u & 802.
1-3 Package Contents Your package contents should include the following parts: • • • • • • One 8-port Auto-sensing switching Hub One DC power adapter This User’s Guide Four rubber feet with adhesive pads Two magnets Warranty card Figure 1.
1-4 Hardware Description The Front Panel The front panel contains power and LED Indicators. Figure 2. Front panel view of the MIL-S800 Front panel LED Indicators Per Device Per Port Power 100M (Link on 100Mbps) LNK/ACT (Link/Activity) FDX/COL (Full Duplex/Collision) For LED details, please refer to Chapter 2, LED Descriptions. The Rear Panel The rear panel of the MIL-S800 consists of a DC power connector and 8 auto-sensing ports. Figure 3.
Chapter 2 Hardware Installation 2-1 Quick Installation • The MIL-S800 should be placed in a well-ventilated room with proper temperature and humidity. • Do not place the unit near water. • The maximum distance between the port to the standard network interface is 100 meters. • • • • • For desktop installation, ensure the surface is clean, smooth, level and sturdy. Apply self-adhesive rubber feet to the bottom of the switch near the corners.
2-2 LED Descriptions Figure 5. Front panel view of LED indicators The following table lists the LEDs and their function.
Chapter 3 Network Application 3-1 Stand Alone The application of a simple standalone switch is illustrated below. The maximum distance between the switch and the workstation is 100 meters. Figure 6. The switch as a backbone for a small 10/100BASE-TX network 3-2 Network You can cascade the MIL-S800 to another hub or a switch without using a crossover cable. Figure 7.
Chapter 4 Troubleshooting • Power If the power indicator is not on after the power cord is plugged in, check the power outlet or power cord. If you lose power after the switch has been operating for some time, check for loose power connections, power losses or surges at the power outlet. Disconnect and reconnect the power. If the problem persists, contact MiLAN Technical Support. • Cabling Verify that the cabling type is correct. Be sure all cable connectors are securely seated in the required ports.
Chapter 5 Product Specification 5-1 General Specification Standard Compliance Number of Ports Data Transfer Rate Network Cables LED Indicators Per Device Per Port IEEE 802.3 10Base-T Ethernet IEEE 802.
90000377_F 9
