TABLET COMPUTER DS11 USER’S GUIDE (Preliminary Version)
Notice Copyright© 2014, MilDef Crete Inc. All rights reserved. No part of this publication may be reproduced and modified without the written permission of MilDef Crete Inc. MilDef Crete Inc. reserves the right to make changes in the products or the product specifications without any prior notice. Customers are advised to contact MilDef Crete Inc. for updated product information. MilDef Crete Inc.
Revision History: Revision Date Changes Author II
Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Regulatory Information/Disclaimers Installation and use of this computer must be in strict accordance with the instructions included in the user documentation provided with the product.
FCC (Federal Communications Commission) Statement This equipment has been tested and found to comply with the limits for a Class-B digital device pursuant part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and radiates radio frequency energy. If not being installed and used in accordance with the instructions, it may cause harmful interference to radio communications.
CE Products with the CE Marking comply with both the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community.
CE Declaration of Conformity It is confirmed to comply with the requirements set out in the Council Directive on the approximation of the laws of the member states relating to Electromagnetic Compatibility (2004/108/EC), Low-voltage Directive (2006/95/EC), the Amendment Directive (93/68/EEC), and the procedures given in European Council Directive (99/5/EC and 2004/108/EC ). The equipment was passed, and the equipment test was performed according to the following European standards: EN 300 328 V1.8.
Power Conservation This tablet computer consumes less power compared to conventional consumer computers. The power consumption may be further reduced by properly configuring the Power Management Setup. It is recommended that the power saving features be enabled even when not running on battery power. Power Management features can conserve power without degrading system performance.
Battery Precautions Only use batteries designed for this tablet computer. Using incompatible battery types may cause explosion, leakage or damage to the computer. Do not remove the battery from the computer while the computer is powered on. Do not continuously use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer is able to continuously work with a damaged battery, the circuit damage may occur and possibly cause fire.
Environmental Information, Material Safety & Recycling All materials used in the manufacturing of this equipment are recyclable or environmentally friendly. Please recycle the packing materials in accordance with local regulations at the end of the product's service life. Notice: The equipment may contain insignificant amount of hazardous substances for health and environment below control level.
TABLE OF CONTENTS CHAPTER 1 - GETTING STARTED............................................................... 1 UNPACKING ..................................................................................................................1 APPEARANCE OVERVIEW ...............................................................................................2 READY FOR USE............................................................................................................7 CHAPTER2 - OPERATING INFORMATION..
CHIPSET .....................................................................................................................44 VGA ..........................................................................................................................45 AUDIO ........................................................................................................................46 INTEL ME ...................................................................................................................
Getting Started Chapter 1 - Getting Started Unpacking The following components come with your computer. If anything is missing or damaged, please notify the dealer immediately.
Getting Started Appearance Overview Note: The following illustrations show the tablet mounted on optional devices, which may not appear on your devices. Front 4 5 6 3 2 2 1 1. Power Button 2. Function keys & Input Lock Key (Please refer to “Using Indicators and Keyboard” for more details) 3. LED Indicators 4. Touch Screen 5. Light sensor 6.
Getting Started Rear 2 1 3 1. Removable battery pack 2. Removable mSATA SSD 3.
Getting Started Left 1 2 1. Optional Fischer I/O 2. Standard: Mini HDMI x 1/USB3.0 x 2 Optional: - GLAN x 1/Mini DisplayPort x 1/USB3.0 x 1 - GLAN x 1/Mini HDMI x 1/USB3.
Getting Started Right 1 2 1. DC-In 12~32V with BVA - Default: Fischer 3-pin connector 2.
Getting Started Top 1 2 3 1. Micro SD Card Slot 2. Optional Built-in Wi-Fi Antenna 3. Optional Built-in GPS Antenna Bottom 1 1. Docklight connector 2.
Getting Started Ready for Use After taking a quick look at your tablet computer, the following illustrations will get you ready for using it. 1. Mounting the Battery A. Mount the battery into the battery bay. B. Turn the battery lock counter-clockwise and lock firmly with a flat-head screwdriver or a coin. B A 2. Connecting the AC Adapter A. Insert the DC Jack firmly. B. Plug the AC cord into the AC adapter. C. Plug the AC power plug into an electrical outlet.
Getting Started 3. Turning ON the Power A. Make sure the battery is securely mounted. Connect all power cords properly. B. Turn on the power of your tablet computer by pressing and holding the Power Button (approx. 2 seconds) until the SSD/ Heater Indicator lights on. Note: The power is able to turn ON without any battery mounted once all the power cords are connected. 4. Turning Off the Power Directly tap “Shut down” from your OS to turn OFF the power of your tablet computer.
Operating Information Chapter2 - Operating Information Start Using Your Tablet Computer Always turn on your tablet computer by using the power button. This is the standard operating procedure to start using your tablet computer. After turning on the power of your tablet computer, it will start with the Operating System (OS) installed. Boot Up When you turn on the power, your computer will start to load the OS into the system memory. This start-up procedure is called “boot up”.
Operating Information Stop Using Your Tablet Computer Each time when you finish working with your tablet computer, there are several ways to stop your tablet computer from operating. Shut down Directly click “Shut down” from your OS to turn OFF the power of your computer. Before shutting down, please do remember to save unfinished works and close your applications to prevent your SSD from suffering possible data loss or damage. “Shut down” will turn OFF power of your computer.
Operating Information Working with Power Button (Heater Kit) Your tablet computer is equipped with a heater kit to enable work under low temperature. The heater will heat up the HDD to the temperature set by the user before booting the system. Also, the heater will constantly monitor HDD temperature. Once the temperature becomes lower, the heater will heat up again to maintain the temperature set by user.
Operating Information Installing Operating System Your computer is designed to operate with Microsoft Windows 7 or Windows 8 32 / 64-bit Operating System. Please connect your computer with an external USB-interface drive to start the OS installation. Note: A USB hub may be required during installation to connect with an external USB-interface ODD, as the System USB port may not supply enough power. Please connect your USB hub with extra power supply to complete the installation.
Operating Information 1st Layer buttons Before using the functions of 1st layer buttons, please make sure that the [Fn Lock] indicator is OFF.
Operating Information 2nd Layer Buttons To perform 2nd layer buttons (functions printed in blue on buttons), press the [Fn Lock] button first, and the Fn Lock indicator will be on, and then press the buttons you would like to perform. A list of functions on 2nd layer button is provided below for operational reference: Button [A1]: Description Windows 8.
Operating Information Input Lock key To prevent from unexpected input by buttons and touch screen, you can press Input Lock key. When Input Lock function is on, the input from devices including buttons and touch screen will be locked. To cancel the input lock function, just press the Input Lock key again and the indicator will be turned off. 1. Press the Input Lock key (as the rectangle one) 2. Input Lock Indicator will light on (as the circled one) 3.
Operating Information Using mSATA SSD Your tablet is equipped with removable mSATA SSD for data storage. The mSATA SSD is user removable for convenience. It can ONLY be removed while power is OFF. To remove the mSATA SSD module, please follow the steps below: 1. Loosen the screws on Back Door Cover, and then remove the cover. 2. Hold the two ends of the mSATA SSD module. 3. Remove the mSATA SSD module from the connector.
Operating Information Using micro SD Cards Your tablet computer is equipped with a micro SD card slot. The slot supports SDHC, SDXC, UHS-1 type micro SD crds. To avoid damages caused by misinsertion, please insert your micro SD card into the card slot properly with the connectors facing down, as shown below.
Operating Information Intel® Rapid Start Technology Your tablet computer can operate Intel® Rapid Start Technology when SSD is installed. This technology enables your system resume time not only to be as fast as wake-up time from S3 (Sleep) mode, but also to be more energy saving.
Operating Information Operating Wireless Devices For your ease of operations, you can turn on/off your wireless devices through the proprietary software application - “Device Power Manager”. Note: Depending on the configuration of your tablet computer, your Device Power Manager menu may appear differently from the screenshots provided in this section. When you adjust User Account Control (UAC), a security feature in Windows, the setting value of Device Power Manager will be affected.
Operating Information 2. Launch the Device Power Manager After launching the utility, please tap “Bluetooth” to enable the Bluetooth function (tap again to disable). Once the Bluetooth function starts up, the wireless LED indicator (color blue) will turn on and the Bluetooth icon will show up in the operating system accordingly. Once the Bluetooth function starts up, the wireless device LED indicator will turn on (color blue) and the Bluetooth icon will appear in the OS accordingly.
Operating Information Wireless LAN (Option) Wireless LAN is an optional wireless communication module for your tablet computer. An embedded antenna will be pre-installed in your tablet computer to access the internet wirelessly. To activate your Wireless LAN function, please follow the illustrations below: 1. Driver & Application Installation a. Install the Chipset Driver first. Read from the Utility DVD and find the directory listed in the readme file to finish installation. b.
Operating Information GPS (Option) GPS is an optional module for your tablet computer. This GPS module supports both GPS and GLONASS systems. An embedded antenna is pre-installed in your tablet computer to support the functions of your GPS and GLONASS. 1. Driver & Application Installation a. Install the Device Power Manager application: Read from the Utility DVD and find the directory listed in the readme file to finish installation. b.
Operating Information Chapter Two - 23
Managing Power Chapter3- Managing Power AC Adapter The AC adapter performs two functions: - It powers the computer from an external AC source. - It charges the computer battery. The adapter automatically detects the AC line voltage (110V or 220V) and adjusts accordingly. The following are recommended when using the AC adapter: - Use a properly grounded AC outlet. - Use one AC outlet exclusively for the computer. Having other appliances on the same line may cause interference.
Managing Power Battery The computer will automatically switch to battery when the external power source (AC adapter or optional vehicle adapter) is disconnected. Battery Power Saving Tips The computer comes with an intelligent power-saving feature. You may extend the battery life by: - Setup power saving functions in Operating System Power Management options (e.g. Windows Power Options). - Lower the intensity of the display by brightness control.
Managing Power Battery Level You may check battery status from Operating System. In Windows, you can click the power/battery icon to reveal the battery gauge window. The following is the illustration of Battery Gauge in Windows OS. An alternative way to check the battery level is by viewing the battery gauge on the battery pack. By pressing the button, indicators will be on. The more indicators are on, the more power remains in the battery.
Managing Power Note: Battery characteristic varies depending on factors such as ambient temperature, charging method, load current, aging, etc. For example, the chemicals of the battery are more inactive at low temperature, thus decreases the output power. The battery gauge should only be used as a reference. Please do not expect it to show the exact amount of the power remaining. There is no memory effect on Lithium Ion battery cells.
Managing Power ACPI Support Your computer supports ACPI (Advanced Configuration and Power Interface) for power management. With ACPI and an ACPI-compliant operating system (such as Microsoft Windows), this feature will allow you to reduce the power consumption and conserve energy. By supporting ACPI, the AC adapter LED and the Power indicator LED will show in different ways.
Managing Power USB Fast Charging Your tablet supports USB fast charging feature, enabling to quickly charge your fast-charging compatible devices. But note, fast charging is not supported in every power mode. The following table shows details for USB Charging information: Mode Power off Power on S3 USB 3.
Optional Devices BIOS Setup Chapter 4 - BIOS Setup Press [F2] + [Delete] at boot up to enter BIOS setup. Use arrow keys to select options and [+/-] to modify them. When finished, move to “Exit” and press [Enter] then confirm save by pressing [Y].
Optional Devices BIOS Setup Advanced Menu Main Advanced Aptio Setup Utility Chipset Boot ► Trusted Computing ► CPU Configuration ► SATA Configuration ► Thermal Configuration ► Intel (R) Rapid Start Technology ► USB Configuration ► Super IO Configuration ► RF Device Configuration ► EC Thermal Control ► AC IN BOOT Control ► USB CHARGE Control ► Intel (R) Smart Connect Technology ► Network Stack Configuration ► CPU PPM Configuration Security Trusted Setting →←: Save & Exit Computing Select Screen ↑↓: S
Optional Devices BIOS Setup Advanced Menu Selections You can make the following selections on the Advanced Menu.
Optional Devices BIOS Setup Trusted Computing Sub-Menu Aptio Setup Utility Advanced Configuration Security Device Support [Disable] Current Status Information SUPPORT TURNED OFF Enables or Disables BIOS support for security device. O.S. will not show Security Device. TCG EFI protocol and INT1A interface will not be available. →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt.
Optional Devices BIOS Setup SATA Configuration Sub-Menu Aptio Setup Utility Advanced Determine how SATA controller(s) operate. SATA Mode Selection SATA Test Mode Aggressive LPM Support SATA Controller Speed [AHCI] [Disabled] [Enabled] [Gen3] Serial ATA Port 0 Software Preserve Serial ATA Port 1 Software Preserve Serial ATA Port 2 Software Preserve Empty Unknown Empty Unknown SATA SSD (120.0 SUPPORTED →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt.
Optional Devices BIOS Setup Intel (R) Rapid Start Technology Sub-Menu Aptio Setup Utility Advanced Intel (R) Rapid Start Technology [Disabled] Enables or disable Intel (R) Rapid Start Technology →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt.
Optional Devices BIOS Setup USB Configuration Sub-Menu Aptio Setup Utility Advanced Enables Legacy USB support. AUTO option disables legacy support if no USB devices are connected. Disable option will keep USB devices available only for EFI applications USB Configuration USB Devices: 1 point Legacy USB Support USB3.0 Support XHCI Hand-off EHCI Hand-off [Enabled] [Enabled] [Enabled] [Disabled] →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt.
Optional Devices BIOS Setup RF Device Control Configuration Sub-Menu Aptio Setup Utility Advanced RF Device Control Setting RF Device Control GPS STATUS GPS BT STATUS BLUETOOTH WLAN STATUS WLAN Present [Enabled] Present [Enabled] Present [Enabled] →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt.
Optional Devices BIOS Setup EC Thermal Control Sub-Menu Aptio Setup Utility Advanced EC Thermal Control Setting EC Thermal Control User mode [Normal mode - 87 C] →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit EC Thermal Control Sub-Menu Selections You can make the following selections on the EC Thermal Control sub-menu.
Optional Devices BIOS Setup Chipset Menu Main Advanced Aptio Setup Utility Chipset Boot Security Save & Exit PCH Parameters ► PCH-IO Configuration ► System Agent (SA) Configuration →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Chipset Menu Selections You can make the following selections on the Chipset sub-menu.
Optional Devices BIOS Setup PCH-IO Configuration Sub-Menu Selections You can make the following selections on the PCH-IO Configuration sub-menu.
Optional Devices BIOS Setup Boot Menu Aptio Setup Utility Main Advanced Chipset Boot Boot mode select [Legacy] Boot Option Priorities Boot Option #1 [Hard Disk: SATA SSD...] Boot Option #2 [CD/DVD] Boot Option #3 [USB Hard Disk] Boot Option #4 [USB CD/DVD] Boot Option #5 [USB Key] Boot Option #6 [USB Floppy] Boot Option #7 [Network] ► CSM parameters ► Hard Disk Drive BBS Priorities Security Save & Exit Set boot LEGACY/UEFI mode →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt.
Optional Devices BIOS Setup Security Menu Main Aptio Setup Utility Chipset Boot Advanced Security Save & Exit Set Password Password Description If ONLY the Administrator’s password is set, then this only limits access to Setup and is only asked for when entering Setup. If ONLY the User’s password is set, then this is a power on password and must be entered to boot or enter Setup. In Setup the User will have Administrator rights.
Optional Devices BIOS Setup Save & Exit Menu Main Advanced Aptio Setup Utility Chipset Boot Save Changes and Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset Save Options Save Changes Discard Changes Restore Defaults Save as User Defaults Restore User Defaults Boot Override PO: MRMAJAA128GTSM2IDO Security Save & Exit Exit system setup after saving the changes →←: Select Screen ↑↓: Select Item Enter: Select +/–: Change Opt.
Optional Devices Drivers and Applications Chapter 5 – Drivers and Applications The Utility DVD includes all the drivers for the installed devices in your tablet computer. Please consult the dealer if there is any driver missing. Also, through Device Manager in Windows, you are able to perform “Driver Update” or check if there are still drivers for the devices needed to be installed. Please check the readme file on Utility DVD to get the latest information before installing device drivers.
Optional Devices Drivers and Applications VGA Windows 8.1/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\VGA(Intel_HD4000)\Windows (64-bit)\win64_153322", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\VGA(Intel_HD4000)\Windows (32-bit)\win64_153322", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\VGA(Intel_HD4000)\Windows (64-bit)\Win64_15313", and
Optional Devices Drivers and Applications Audio Windows 8.1/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Audio\Windows 7_8_8.1\Win7_Win8_Win81_R273", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\Audio\Windows 7_8_8.1\6777_PG360_Win8_Win7_Vista_XP", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Audio\Windows 7_8\6777_PG360_Win8_Win7_Vista_XP", a
Optional Devices Drivers and Applications Intel ME Windows 8.1/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Intel_ME_8.1\Windows 7_8_8.1", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\Intel_ME_8.1\Windows 7_8_8.1", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Intel_ME_8.1\Windows 7_8", and then follow the instructions to install.
Optional Devices Drivers and Applications Intel Rapid Storage Technology Windows 8.1/Ultimate 64-bit: Run "SetupRST.exe" in the directory of "Drivers\Intel Rapid Storage Technology\Windows 7_8_.81\12.9", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "SetupRST.exe" in the directory of "Drivers\Intel Rapid Storage Technology\Windows 7_8_.81\12.9", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "SetupRST.exe" in the directory of "Drivers\Intel Rapid
Optional Devices Drivers and Applications Wireless Power Manager Windows 8.1/Ultimate 64-bit: Run "setup.exe" in the directory of "\Utilities\10_0_2_5\", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "setup.exe" in the directory of "\Utilities\10_0_2_5\", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "setup.exe" in the directory of "\Utilities\10_0_2_5\", and then follow the instructions to install. Windows 8/Ultimate 32-bit: Run "setup.
Optional Devices Drivers and Applications Touch Pad Windows 8.1/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Touch Pad (ETD)\Windows 7_8_8.1\ETD11.10.13.6_ps2drv_WHQL", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\Touch Pad (ETD)\Windows 7_8_8.1\ETD11.10.13.6_ps2drv_WHQL", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Touch Pad (ETD)\Windows 7_
Optional Devices Drivers and Applications Turbo Boost Monitor Windows 8.1/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Turbo Boost Monitor\Windows 7_8_8.1", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\Turbo Boost Monitor\Windows 7_8_8.1", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\Turbo Boost Monitor\Windows 7_8", and then follow the instru
Optional Devices Drivers and Applications Gigabit LAN (Option) Windows 8.1/Ultimate 64-bit: Run "PROWinx64.exe" in the directory of "\Drivers\Intel_82579LM\Windows 8_1 (64-bit)", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "PROWinx32.exe" in the directory of "\Drivers\Intel_82579LM\Windows 8_1 (32-bit)", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "PROWinx64.exe" in the directory of "\Drivers\Intel_82579LM\Windows 8 (64-bit)", and then follo
Optional Devices Drivers and Applications 2nd Gigabit LAN (Option) Windows 8.1/Ultimate 64-bit: Run "setup.exe" in the directory of "\Drivers\Mini PCI-E 1G RTL8111E LAN\Windows 7_8_8.1\Install_Win7_7046_07202011", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: Run "setup.exe" in the directory of "\Drivers\Mini PCI-E 1G RTL8111E LAN\Windows 7_8_8.1\Install_Win7_7046_07202011", and then follow the instructions to install. Windows 8/Ultimate 64-bit: Run "setup.
Optional Devices Drivers and Applications WiFi (Option) Windows 8.1/Ultimate 64-bit: Run "Wireless_15.6_De64.exe" in the directory of "\Drivers\Mini PCI-E WiFi 6235\Windows 8_1 (64-bit)", and then follow the instructions to install. *: Then into the“Wireless Power Manager”to turn on the WLAN device. Windows 8.1/Ultimate 32-bit: Run "Wireless_15.6_De32.exe" in the directory of "\Drivers\Mini PCI-E WiFi 6235\Windows 8_1 (32-bit)", and then follow the instructions to install.
Optional Devices Drivers and Applications Bluetooth (Option) Windows 8.1/Ultimate 64-bit: *: First into the "Wireless Power Manager" to turn on the Bluetooth device. Run "BT_2.6.1211_e64.exe" in the directory of "\Drivers\Bluetooth\Windows 8_1 (64-bit)", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: *: First into the "Wireless Power Manager" to turn on the Bluetooth device. Run "BT_2.6.1211_e32.exe" in the directory of "\Drivers\Bluetooth\Windows 8_1 (32-bit)", and then follow t
Optional Devices Drivers and Applications GPS (Option) Windows 8.1/Ultimate 64-bit: *: First into the "Wireless Power Manager" to turn on the GPS device. Run "ubloxGnss_sensor_windows_3264_v2.1.0.5.exe" in the directory "\Drivers\GPS(u-blox)\Windows 7_8_8.1", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: *: First into the "Wireless Power Manager" to turn on the GPS device. Run "ubloxGnss_sensor_windows_3264_v2.1.0.5.exe" in the directory "\Drivers\GPS(u-blox)\Windows 7_8_8.
Optional Devices Drivers and Applications TPM (Option) Windows 8.1/Ultimate 64-bit: *: First into the "BIOS" to turn on the TPM device. Run "Setup.exe" in the directory of "\Drivers\TPM\Windows 7_8_8.1", and then follow the instructions to install. Windows 8.1/Ultimate 32-bit: *: First into the "BIOS" to turn on the TPM device. Run "Setup.exe" in the directory of "\Drivers\TPM\Windows 7_8_8.1", and then follow the instructions to install.
Optional Devices Drivers and Applications USB3.0 (For Windows 7) Windows 7/Ultimate 64-bit: Run "Setup.exe" in the directory of "\Drivers\USB3.0\Windows 7\Intel(R) USB 3.0 eXtensible Host Controller Driver PV(HF7) 1.0.7.248", and then follow the instructions to install. Windows 7/Ultimate 32-bit: Run "Setup.exe" in the directory of "\Drivers\USB3.0\Windows 7\Intel(R) USB 3.0 eXtensible Host Controller Driver PV(HF7) 1.0.7.248", and then follow the instructions to install. Note: USB3.
Specifications Chapter 6 – Specifications Platform Intel® Chief River Platform CPU Intel® Ivy Bridge i7-3537U 4 MB Intel Smart Cache Memory PCH Intel® Panther Point QM77 Memory 4/8GB System Memory Industrial grade DDR3 SO-DIMM x 1, 1600MHz Touch Screen Type: 10.1” WXGA (16:10) Resolution: 1280 x 800 pixels Brightness (min.~ typ.
Specifications Audio HD Audio and mono Speakers Embedded Digital Mic • • I/O Ports Std. Mini HDMI x 1/USB3.0 x 2 ((the rightmost USB port, with a lightening mark on the cap, supports fast charging function) Optional: - GLAN x 1/ Mini DisplayPort x 1/USB3.0 x 1 - GLAN x 1/Mini HDMI x 1/USB3.0 x 1 Optional Fischer I/O: Choose 1~4 out of 7 as below: - USB 2.
Specifications Dimensions and Weight Width: Depth: Height: Weight: 280mm (11”) 186mm (7.3”) 20mm (0.79”) Kg ( lb)* *Without battery, mSATA module, and all RF modules. Battery weight: approx. 300g. Note: Weight varies depending on system configurations. Power Easily-removable Battery Pack: Type: 6 x 18650 cells Lithium Ion Capacity: 11.1V/ 4400mAh (3S2P) Dimensions: 138 mm (W) x 136 mm (D) x 9.7 mm (H) Weight: Approx. 300 gram (0.66 lb.
Specifications Operating & Storage Temperature Operating Temp.: - Std: I: 0 °C ~ +40 °C M: -20 °C ~ +55 °C* *LCD with Heater Optional: -30 °C ~ +55 °C* Storage Temp.
Optional Devices Chapter 7 – Optional Devices Communication WiFi/Bluetooth: - Intel® Centrino® Advanced-N 6235, Dual Band - Board Form Factor: PCIe Half Mini Card - Wi-Fi Certified: 802.11 a/b/g/n - Bluetooth: Supports BT 2.1, 2.1+EDR, 3.0, 3.0+HS, 4.0 (BLE) - Interface: PCIe (WiFi)/USB (BT) GPS: u-blox Neo-M8 (USB interface) 2nd Gigabit LAN: 1Gbps (internal Mini PCIe Card) Memory Card The memory card will expand main memory to facilitate better system performance.
Optional Devices External USB Keyboard An optional 89-key external USB keyboard with LED backlight and IP rating of IP54 is available for your tablet computer. The detailed specification is provided below: 89-key layout emulates 101/102-key KB Life: >1 million times, water/dust protection up to IP54 Back-light illumination (backlight device: green LED) PS/2 compatible Trackpoint and mouse buttons Dimensions: 323.4 mm (W) x 172 mm (D) x 25 mm (H) Weight: 1.
Optional Devices Mini Keyboard KBD Mini Keyboard KBD is designed for all models. KBD also brings convenience of use through multi-language keyboard versions and USB interface. The detailed specification is provided below: USB interface with 30 cm USB cable 66-Key design with function keys to simulate standard keyboards. StickPointer to simulate mouse and keypad Currently support versions: English (UI), English (UK), German (DE), Swedish (SV) and Russian (RU) 5 versions.
Maintenance and Service Chapter 8 – Maintenance and Service Cleaning ALWAYS turn OFF the power, unplug the power cord and remove the battery before cleaning. The exterior of the system and display may be wiped with a clean, soft, and lint-free cloth. If there is difficulty removing dirt, apply non-ammonia, non-alcohol based glass cleaner to the cloth and wipe. An air gun is recommended for cleaning water and dust. For salty water please clean with fresh water then blow-dry with an air gun.
Maintenance and Service RMA Service If troubleshooting solutions are unsuccessful, consult your dealer for RMA. Shipping instructions: 1. Remove any personal add-on devices or other media. 2. Use the original shipping container and packing materials, if possible. 3. If the original packing materials are not available, wrap the equipment with soft material (e.g. PU/PE form) then put the wrapped equipment into a hard cardboard shipping box. 4.
