Full Product Manual

ManualsBrandsMilescraft ManualsPower Tool AccessoriesTrack Saw Guide - Universal Compatibility for Circular Saws. Expandable 50 in. Cutting Range. All Aluminum Construction.

GB F

E D

Model

Modèle

Modelo

Modell

1409

Extend your cut length

by adding our #1408

extension set.

TrackSawGuide™

1 — Aluminum Guide Rail 27.5″ (2)

1a — Rail End Caps (4)

1b — Guide Strips (2)

2 — TrackClamp (2)

3 — Saw Blade Spacer (1)

4 — Rail Connector (2)

5 — Vertical Clamp Spacer (4)

6 — 3mm Hex Key (1)

7 — Glide Adjusters (4)

8 — TrackSaw Base

8a — Saw Clamp (2)

8b — Saw End Stop (2)

8c — Long Reach Saw Clamp (2)

TrackSawguide™

1 — Riel guía de aluminio de 27.5″ (2)

1a — Cubierta del Riel (4)

1b — Barra para Guiar (2)

2 — TrackClamp para Riel (2)

3 — Separador de la hoja de sierra (1)

4 — Conector del riel (2)

5 — Separador del Sujetador Vertical (4)

6 — Llave Allen de 3 mm (1)

7 — Ajustadores deslizantes (4)

8 — Base de la TrackSaw

8a — Sujetador de la Sierra (2)

8b — Tope final de la sierra (2)

8c — Sujetador Largo de la Sierra (2)

SCAN,

LEARN,

BUILD.

TrackSawGuide™

1 — Glissière de Guidage Aluminium 27.5″ (2)

1a — Butée d’extrémité de glissière (4)

1b — Bande de Guidage (2)

2 — Serre-Joint TrackClamp (2)

3 — Entretoise de Lame de Scie (1)

4 — Connecteur de Glissières (2)

5 — Entretoise verticales de serrage (4)

6 — Clé Allen de 3 mm (1)

7 — Correcteurs de Coulissement (4)

8 — Socle de Scie Circulaire

8a — Barrette de Maintien de la Scie (2)

8b — Butée d’Extrémité de Scie (2)

8c — Barrette Longue de Maintien de la Scie (2)

TrackSawGuide™

1 — Führungsschiene, 700mm (2)

1a — Abschlusskappen (4)

1b — Splitterschutz (2)

2 — T-Nut Zwinge (2)

3 — Sägeblatt-Ausrichthilfe (1)

4 — Verbinder (2)

5 — Distanzstücke (4)

6 — Inbusschlüssel, 3mm (1)

7 — Gleiteinlagen (4)

8 — Aufnahmeschlitten

8a — Spannarm, kurz (2)

8b — Sägeanschlag (2)

8c — Spannarm, lang (2)

Summary of content (10 pages)

PAGE 1
Model Modèle Modelo Modell TrackSawGuide™ GB 1 — Aluminum Guide Rail 27.5″ (2) 1a — Rail End Caps (4) 1b — Guide Strips (2) 2 — TrackClamp (2) 3 — Saw Blade Spacer (1) 4 — Rail Connector (2) 5 — Vertical Clamp Spacer (4) 6 — 3mm Hex Key (1) 7 — Glide Adjusters (4) 8 — TrackSaw Base 8a — Saw Clamp (2) 8b — Saw End Stop (2) 8c — Long Reach Saw Clamp (2) TrackSawguide™ TrackSawGuide™ 1409 F 1 — Glissière de Guidage Aluminium 27.
PAGE 2
GB F TABLE OF CONTENTS: TABLE DES MATIÈRES E TABLA DE CONTENIDOS: D INHALTSVERZEICHNIS: Table of Contents .................................................................2 Table des Matières ..............................................................2 Tabla de Contenido .............................................................2 Inhaltsverzeichnis ...............................................................2 Package Contents ...............................................................
PAGE 3
GB SAFETY WARNING: Read, understand, and follow your power tool manufacturer’s instructions for safety. Always wear safety glasses or eye shields before commencing power tool operation. Always keep hands, face, hair, loose clothing, and body at a safe distance from spindles and cutting tools. Always keep a firm grip on tool handles when in operation. Always disconnect from power source before adjusting power tools. Always make sure work area is clear of debris and tools before operating your circular saw.
PAGE 4
GB F E D ASSEMBLING THE TRACK 1Place the Aluminum Guide Rails face down (The CONTENU DE L’EMBALLAGE 1Positionnez les glissières en aluminium face vers le CONTENIDO DEL PAQUETE 1Coloque los rieles guía de aluminio boca abajo (el logo MONTAGE DER FÜHRUNGSSCHIENE 1Legen Sie die Alu-Führungsschienen so auf eine flache 2Remove the Rail End Caps from the Aluminum Guide 2Retirez les Butées des extrémités des Glissières en 2Entfernen Sie die Abschlusskappen an den Enden der 3Slide the Rail Connectors hal
PAGE 5
GB F E MOUNTING CIRCULAR SAW TO THE TRACKSAW BASE MONTAGE DE LA SCIE CIRCULAIRE SUR LE SOCLE FIJACIÓN DE LA SIERRA CIRCULAR A LA BASE DISCONNECT THE SAW FROM POWER BEFORE MOUNTING IT TO THE TRACKSAW BASE Place the Saw Blade Spacer on the edge of your work 1 surface overhanging the edge with logo facing up. (FIG. 4) 2Position the middle section of the TrackSaw Base on top of the Saw Blade Spacer so that it sits into the guide tracks and lays flat on work surface. (FIG.
PAGE 6
GB F E D MOUNTING CIRCULAR SAW TO TRACKSAW BASE(CONTINUED) 6Your saw blade must rest flush against the side of the MONTAGE DE LA SCIE CIRCULAIRE SUR LE SOCLE (SUITE) 6Votre lame de scie doit reposer à fleur contre le côté FIJACIÓN DE LA SIERRA CIRCULAR A LA BASE (CONTINUADO) 6La hoja de sierra debe estar nivelada con el costado MONTAGE DER HANDKREISSÄGE AUF DEM AUFNAHMESCHLITTEN 6Das Sägeblatt muss bündig mit der Vorderseite der 7Slide the Saw End Stop at the front of the TrackSaw 7Faites coulisser
PAGE 7
GB CALIBRATING THE GUIDE RAIL AND SAW i The sacrificial cutting strip requires you to calibrate the TrackSaw Base to your saw. Use a 48” (122cm) long piece of scrap wood. 1Using the provided TrackClamps™, secure the Aluminum Guide Rail to your scrap board using the center T-Track. (FIG. 12) i The Aluminum Guide Rail should extend past your workpiece on both sides of your cut (FIG. 13). 2Re-attach the Rail End Caps into the ends of your track.
PAGE 8
GB F ALIGNING THE GUIDE RAIL Once the Guide Strip has been cut, the Guide Rails are now calibrated to your saw and that blade. i 1Mark your cut line on your workpiece. 2Align the red Guide Strip to line. (FIG. 16) The edge of the Red Guide Strip indicates where the saw blade will cut your material. i 3Remove the Rail End Caps. 4Using the provided TrackClamps, secure the Guide Rail to your workpiece using the center T-Track located on the bottom of the Guide Rail.
PAGE 9
GB F MAKING THE CUT 1Set the depth of cut by placing the circular saw and TrackSaw Base on the track and lowering blade. The cut should not exceed 1/8” (3mm) deeper than board. (FIG. 18) 2Engage the TrackSaw Base into the Aluminum Guide Rail, be sure the blade is clear of workpiece. (FIG. 19) 3Cut until your piece is finished. (FIGs. 20 - 20a) We recommend the Guide Rail to overhang the workpiece as much as possible at the start of cut versus the end of cut.
PAGE 10
LEGEND Model Modèle Modelo Modell Phillips Head · Tête Phillips · Cabeza Phillips · Phillips Kopf Square Nut ·Écrou carré · Tuerca cuadrada· Vierkantmutter Figure Number Part Number DESCRIPTION G LA DESCRIPTION F DESCRIPCIÓN 3 BESCHREIBUNG d 1409 QTY 21080 Aluminum Guide Rail 27.