IoT Display DS7610 User Guide
Safety Precautions Milesight will not shoulder responsibility for any loss or damage resulting from not following the instructions of this operating guide. The device must not be disassembled or remodeled in any way. Do not place the device outdoors where the temperature is below/above operating range. Do not place the device close to objects with naked flames, heat source (oven or sunlight), cold source, liquid and extreme temperature changes.
Contents 1. Product Introduction ......................................................................................................................... 4 1.1 Overview ...................................................................................................................................4 1.2 Features ................................................................................................................................... 4 2. Hardware Introduction .....................................
1. Product Introduction 1.1 Overview DS7610 IoT Display brings customers simplicity and a user-friendly experience in managing spatial conditions in rooms, offices, and buildings with just one single tap. As an advanced IoT solution, DS7610 has a built-in LoRaWAN® gateway and NFC to manage Milesight LoRaWAN® sensors and display intuitive data and the status on the screen. More significantly, the 10.
Built-in ambient light sensor and proximity sensor automatically adjust the screen’s brightness according to external light conditions for saving energy 2. Hardware Introduction 2.
4 NFC area 5 Back LED light strip 6 Wall mount hole 7 VESA 75*75mm 8 Type-C port 9 DC power jack 10 Ethernet port (PoE PD) Note: 1) To use the back LED light strip, please remove the blackout tape. 2) DS7610 does not support inserting micro SD card since micro SD slot is inside the device, please contact Milesight to preinstall the micro SD card before shipment. 3) There is a recovery button next to the type-C port, please do not press and hold it.
Powered by a PoE switch Connect the Ethernet cable of the IoT Display to a PoE switch. Powered by a DC power adapter Connect the DC power jack of the IoT Display and the power outlet with a DC power adapter (3.5 * 1.3mm plug). Powered by a Type-C port Connect the Type-C port of the IoT Display and the power outlet with a Type-C cable. 4. Software Guide 4.1 Basic Screen Description Home Screen In the home screen, you can swipe up from the bottom to bring up the Application page.
Application In the Application page, you can check and install applications and open them as necessary. You can also create a shortcut by long-pressing the app icon and dragging it to the home screen. Status Bar Volume-: Decrease the system volume. Back: Return to the previous page. Home: Return to the home page.
Recents: Switch between recently used applications, or take screenshot of the applications. You can also close an application by pulling up it. Volume+: Increase the system volume. Status Notifications Status notification bar displays system status such as time, Wi-Fi, USB connections, etc. You can drop down the notification bar to open the shortcut window and check the details of notifications. 4.2 Communication 4.2.
4.2.2 Ethernet Connection On Application page, go to Settings > Network & Internet, enable Ethernet. Select Ethernet IP mode as static or dhcp and plug the Ethernet cable to Ethernet port of device to access the network.
4.2.3 LoRaWAN® Gateway DS7610 has a built-in one-channel LoRaWAN® gateway to manage Milesight LoRaWAN® end devices. On Application page, go to Settings > Network & Internet, enable Lora Gateway. Select corresponding parameters to communicate with LoRaWAN® end devices.
Parameters Gateway EUI Description Unique identifier of the device, it’s fixed and not allow to change. Select the LoRaWAN® frequency plan used for the upstream and downlink Channel Plan frequencies and data rates. Available channel plans depend on the gateway’s model. Frequency Select the frequency to receive uplinks and send downlinks. Spreading Factor Select the spreading factor to send downlinks. Mode It’s fixed as Embedded Network Server mode. 4.2.
NFC feature, then attach NFC devices to the NFC area of DS7610 to exchange the data. You can use NFC to achieve Milesight LoRaWAN® nodes configurations, ID identifications, contactless meeting check-in, etc. 4.2.6 USB Plug the USB Type-C port of DS7610 to your USB devices. On Application page, go to Settings > Connected devices > USB to select the USB usage as your requirement. USB can be used to connect to computer, USB drive, USB microphone, etc. Note: 1) The default USB mode of device is OTG.
4.3 DS Demo App DS Demo App supports the configuration of basic parameters of device and it can’t be uninstalled. Parameter SN Light Level Distance Sensor Automatic Screen Switch Description Show the SN of this device. Show the environment brightness level between 1 to 5 in real time. The light sensor can be used to adjust the brightness of screen on Settings > Display > Adaptive brightness. Detect if there is any object approaching the screen.
4.4 Install & Uninstall Apps Install Apps 1. Select USB mode as File Transfer, then import your app(.apk) to the device via USB port. Note that DS7610 only supports 32-bit App. 2. On Application page, go to Files to find the apk file and click it to install the App. 3. After install, you can find the app on Application page. Uninstall Apps On Application page, go to Settings > Apps & Notifications to find the app file in the app list and click it to check app info and uninstall the App.
2. Go to DS Demo App, click System Upgrade button to enter upgrading page. 3. Click Plus symbol to select the target firmware from Files, then click Upgrade button to upgrade the firmware. Note: 1) Do not power off the device during the upgrade process, as this will result in operating system errors. 2) DS Demo App does not support system downgrade. If you need to downgrade, please contact Milesight technical support . 4.
4.8 App Development DS7610 is based on Android 11 system and please refer to Android official developer guide to complete the development: https://developer.android.com/guide Besides, Milesight also provides SDK and Developer API Documentations relating LoRaWAN® gateway feature, NFC feature relating Milesight LoRaWAN® Device management: https://github.com/Milesight-IoT/DS7610-SDK For more info please contact Milesight technical support: https://support.milesight-iot.com 5. Installation Wall Mounting 1.
3. Press the bracket on the wall with the TOP logo side facing up and align its holes with the wall plugs, then fix the screws into the wall plugs. 4. Plug an Ethernet cable into the Ethernet port of the IoT Display. 5. Mount the IoT Display on the Wall Mount Bracket. 6. Fix the IoT Display to the bracket by tightening the 2 screws at the bottom of the bracket.
Glass Mounting 1. Attach the tape on the back of the Wall Mount Bracket, and attach the bracket at the desired height on the glass with the TOP logo side facing up. 2. Plug an Ethernet cable into the Ethernet port of the IoT Display. 3. Mount the IoT Display on the Wall Mount Bracket.
4. Fix the IoT Display to the bracket by tightening the 2 screws at the bottom of the bracket. VESA Desktop Stand Mounting 1. Plug an Ethernet cable into the Ethernet port of the IoT Display, then lift the IoT Display and align its VESA holes with the VESA desktop stand. 2. Fix the IoT Display to the VESA desktop stand by tightening the screws.
