Operating Instructions and Installation Instructions

ManualsBrandsMill ManualsAir ConditioningIB800L DN

ASSEMBLY AND INSTRUCTION MANUAL (EN)

Please read the instrucons carefully before use. Take good care of this manual for later use.

This assembly and instrucon manual applies to the following panel heaters:

IB300, IB600DN, IB900DN, IB1200DN, IB800L DN, IB1000L DN

IB600DN G, IB1200DN G, IB800L DN G

MB300, MB600DN, MB900DN, MB1200DN, MB800L DN, MB1000L DN

PH600DN, PH1000DN, PH600L DN, PH800L DN

PH600DN S, PH1000DN S, PH600L DN S, PH800L DN S

PH600DN G, PH1000DN G, PH600L DN G, PH800L DN G

Series: Steel & Glass

Summary of content (15 pages)

PAGE 1
ASSEMBLY AND INSTRUCTION MANUAL (EN) Series: Steel & Glass Please read the instructions carefully before use. Take good care of this manual for later use.
PAGE 2
Contents Important safety information .................................................................................................... 3 Description of the heater ........................................................................................................... 6 Assembly .................................................................................................................................... 7 Electronic thermostat — Instructions….……………...................................
PAGE 3
Important safety information You must obey common safety guidelines when using electrical products, especially in the presence of children. WARNING! To avoid electric shock or damage due to the heat, always make sure the plug is pulled out before the heater is moved or cleaned. Read the instructions carefully. The product is intended for home use only. Make sure the heater is connected to the house's regular mains (230 V), as it indicated on the heater.
PAGE 4
The device cannot be used by children under 8 years of age and persons with reduced physical or mental abilities or lack of experience and knowledge unless they have been given supervision or instruction in the safe use of the device and understand the hazards involved. Children should not play with the device. Cleaning and maintenance should not be done by unsupervised children. Children under the age of 3 should be kept away from the device, unless they are under constant supervision.
PAGE 5
STORE THIS INSTRUCTION MANUAL FOR FUTURE USE! NEVER TOUCH YOUR PANEL HEATER OR ITS CASING WITH WET HANDS! Specifications Model Thermostat Color Height Width Amperage Power (W) IP rating IB300 Electronic White 30.0 cm 35.0 cm ~230 V / 50 Hz 300 IPx4 IB600DN Day/night White 40.0 cm 65.0 cm ~230 V / 50 Hz 600 IPx4 IB900DN Day/night White 40.0 cm 85.0 cm ~230 V / 50 Hz 900 IPx4 IB1200DN Day/night White 40.0 cm 105.
PAGE 6
Minimum distances Description of the heater Mill Steel 1. Off/On 2. Wall bracket 3. Temperature sensor 4. Heat emission 5. Steel front 6. Thermostat Mill Glass EN 6 millheat.
PAGE 7
Assembly Use a tape measure and a spirit level to mount the bracket 1. Drill holes in the wall for holes 1 & 2. Then drill holes in the wall for the topmost holes (holes 3 & 4 by using B) 2. Insert the wall plugs into the drilled holes and attach the bracket with 4 screws 3. Place the heater on the lower lugs on the bracket, then hang the heater on the upper lugs (lift the heater slightly to align the heater with for the upper lugs).
PAGE 8
Electronic thermostat – Instructions CAUTION! In the event of a power cut, the thermostat will return to the last set temperature The section concerning electronic thermostats is relevant for the following models: IB300 MB300 Control panel for electronic thermostat: 1. Display (shows the desired room temperature by default) 2. Power indicator — Shows whether the heater is using power or not 3. Control button (+) (increase temperature) 4. Control button (–) (reduce temperature) 5.
PAGE 9
Power indicator When the panel heater is using power (i.e. when it is heating), the power indicator is lit. 1) Set the desired temperature Press the arrow buttons to set the desired temperature. 2) Temperature calibration *Should any deviations occur between the desired and actual temperature in the room, it can be easily adjusted (the heater should have been set to the same setting for at least 12 hours in order to be sure a calibration is necessary).
PAGE 10
CAUTION! In the event of a power cut, the thermostat will return to the last set temperature Day/night thermostat – Instructions The section concerning day/night thermostat applies to the following models: IB600DN, IB900DN, IB1200DN, IB800L DN, IB1000L DN IB600DN G, IB1200DN G, IB800L DN G MB600DN, MB900DN, MB1200DN, MB800L DN, MB1000L DN PH600DN, PH1000DN, PH600L DN, PH800L DN Tip! The thermostat can be used as a regular electronic thermostat (i.e.
PAGE 11
Power indicator When the panel heater is using power (i.e. when it is heating), the energy indicator is lit. 1) Set the desired temperature Press the arrow buttons to set the desired temperature. Note: Can only be carried out when the setback programs are inactive 2) Daytime setback When you want the heater to reduce the temperature during the day (set for weekdays from now on) press . The display shows "d". Use the arrow buttons to enter the correct weekday.
PAGE 12
3) Nighttime setback When you want the heater to reduce the temperature in the evening (applicable every evening/night from now on) press . The display shows °C. Enter the desired temperature for nighttime setback. Save by pressing . Enter the desired number of hours for nighttime setback. Save by pressing . *Control light is steady green when the heater is in an active setback period. The control light is steady red when the setback period is inactive, but has been programmed.
PAGE 13
6) Change number of hours — Daytime Press and hold and press 2 times. Enter the desired number of hours for daytime setback. Save by pressing or wait 15 seconds for automatic confirmation. 7) Change number of hours — Nighttime Press and hold and press 2 times. Enter the desired number of hours for nighttime setback. Save by pressing or wait 15 seconds for automatic confirmation. 8) Cancel (skip) setback period Press and hold and press or once (depending on which setback period you want to cancel).
PAGE 14
9) Delete a setback program Press and hold or (depending on which setback period you want to cancel) for 3 seconds. 10) Calibration of temperature *Should any deviations occur between the desired and actual temperature in the room, it can be easily adjusted (the heater should have been set to the same setting for at least 12 hours in order to be sure a calibration is necessary). Press 2 times and use the arrow buttons (+ or –) to set the actual temperature observed in the room.
PAGE 15
Maintenance 1) For cleaning, always unplug the heater and leave it to cool. 2) Wipe the heater regularly with a damp cloth and dry the surface before turning on the heater again. 3) The heater must be cleaned at least once a month during the heating season. CAUTION! The heater should never be immersed in water. Avoid using detergents to clean the heater. Never let any water get inside the heater; this can be hazardous. 4) Dust etc. should be removed with a soft cloth.