February 1996 Form: TM-428 Effective With Serial No.
TABLE OF CONTENTS SECTION 1 – SAFETY PRECAUTIONS FOR SERVICING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. 1-2. 1-3. 1 Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Servicing Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 7 – DISASSEMBLY AND REASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1. 7-2. 33 Disassembly Of Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Disassembly Of Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 34 SECTION 8 – MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 1 – SAFETY PRECAUTIONS FOR SERVICING safety_rtm1 4/95 1-1. Symbol Usage Means Warning! Watch Out! There are possible hazards with this procedure! The possible hazards are shown in the adjoining symbols. Y Marks a special safety message. . Means NOTE; not safety related. This group of symbols means Warning! Watch Out! possible ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult symbols and related instructions below for necessary actions to avoid the hazards. 1-2.
HOT PARTS can cause severe burns. 1. Allow cooling period before servicing. 2. Wear protective gloves and clothing when working on a hot engine. ELECTRIC SHOCK HAZARD incorrect use of test equipment. from 1. Stop engine before making or changing meter lead connections. 2. At least one meter lead should be a self-retaining spring clip such as an alligator clamp. 3. Read instructions for test equipment. MAGNETIC CURRENTS operation. FIELDS FROM HIGH can affect pacemaker 1.
SECTION 2 – INSTALLATION 2-1. Installing Welding Generator Movement Airflow Location 18 in (460 mm) Y Do Not Lift Unit From End 18 in (460 mm) 18 in (460 mm) OR OR 18 in (460 mm) 18 in (460 mm) Grounding 1 2 3 3 1 4 GND/PE 4 OR Use #10 AWG or larger insulated copper wire. Y If unit does not have GFCI receptacles, use GFCI-protected extension cord. Electrically bond generator frame to vehicle frame by metal-to-metal contact.
2-3. Fuel Consumption SB-115 572 2-4. Engine Prestart Checks Check all fluids daily. Engine must be cold and on a level surface. 1/2 in (13 mm) Engine stops if oil pressure gets too low. Full Full ST-140 091-E / Ref.
2-5. Connecting The Battery Y Connect (–) cable last. + – Tools Needed: 3/8, 1/2 in Ref. ST-144 839-F / Ref. ST-168 046 / Ref. S-0756-D 2-6. Connecting To Weld Output Terminals Y Use ONLY one set of terminals at a time. Disconnect weld cables from set of weld output terminals not in use. Tools Needed: 3/4 in Miller Legend ST-140 092-B / Ref.
2-7.
SECTION 3 – OPERATING WELDING GENERATOR 3-1. Front Panel Controls 5 6 1 2 7 3 4 Using Idle Lock Switch RUN/IDLE 1860 rpm (Power/Idle) LOCK RUN/IDLE No Load: 1860 rpm (Power/Idle) Load: 3000 rpm (Weld) UNLOCK RUN OR UNLOCK 3000 rpm (Weld) LOCK Ref. ST-168 046 1 Engine Control Switch S2 Use switch to start engine, select speed, and stop engine. In Run/Idle position, engine runs at power/idle rpm at no load, and weld/power rpm under weld or 100 Hz auxiliary power receptacle load.
3-2. Remote Control (Optional) Y Weld output terminals are energized when Remote Control switch S4 is in Panel/On position and engine is running. 1 1 Remote 14 Receptacle RC1 Connect optional remote control to RC1 (see Section 2-8). In Example: Min = 70 A DC Percentage Of Range = 50% Max = 88 A DC (50% of 70 to 105) Max (88 A DC) Min (70 A DC) Set Switch Set Range Set Percentage Adjust Remote Control ST-140 092-B 3-3.
3-4. Volt-Ampere Curves The volt-ampere curves show the minimum and maximum voltage and amperage output capabilities of the welding generator. Curves of other settings fall between the curves shown.
SECTION 4 – OPERATING AUXILIARY EQUIPMENT 4-1. 100 Hz Auxiliary Power Receptacle And Circuit Breaker Y Do not operate 50/60 Hz or 60 Hz equipment from 100 Hz receptacle. 1 115 V 9 A 100 Hz AC Receptacle RC4 Receptacle supplies single-phase power at weld speed only. Total output available is 1 kVA/kW. 2 2 Circuit Breaker CB3 CB3 protects receptacle from overload. If CB3 opens, receptacle does not work. 1 Ref. ST-168 046 4-2.
4-3. 60 Hz Auxiliary Power Receptacles And Circuit Breakers For 60 Hz Auxiliary Power While Welding LOCK For 60 Hz Auxiliary Power Only UNLOCK RUN/IDLE RUN/IDLE 4 0 PANEL 100 0 PANEL ON 1 5 2 3 6 7 9 Y If unit does not have GFCI receptacles, use GFCI-protected extension cord. 1 120 V 15 A AC Duplex Receptacle RC1 2 120 V 15 A AC Duplex Receptacle RC2 3 240 V 30 A Twistlock Receptacle RC3 Receptacles supply 60 Hz single-phase power at power/idle speed only.
SECTION 5 – THEORY OF OPERATION 1 Engine Supplies force to turn revolving fields. 2 Revolving Fields (Rotor) 13 ♦ Turn at 1860 rpm maximum for power/idle and 3000 rpm maximum for weld. The speed and excitation current of the field coils determine voltages in stator windings. 3 Stator Windings Supply power to exciter, auxiliary power, and weld circuits. 4 Fuse F1 Protects exciter excitation winding from overload.
13 Remote Control Switch S4 Selects Panel or remote amperage control. 14 Circuit Breakers CB1, CB2, CB5, And CB7 Protect 50/60 Hz auxiliary power receptacles RC1, RC2, and RC3 from overload. 15 50/60 Hz Auxiliary Power Receptacles RC1, RC2, And RC3 Provide connection points and power for auxiliary equipment. 16 Circuit Breaker CB3 Protects 100 Hz auxiliary power receptacle RC4 from overload. 17 100 Hz Auxiliary Power Receptacle RC4 Provides connection point and power for auxiliary equipment while welding.
NOTES TM-428 Page 14 Miller Legend
SECTION 6 – TROUBLESHOOTING 6-1. Troubleshooting Tables A. Welding . See Sections 6-2 and 6-3 for test points and values and Section 10 for parts location. Trouble No weld output. Remedy Check fuse F1, and replace if necessary (see Section 8-6). Check integrated rectifier SR2, and replace if necessary. Check diode D4, and replace if necessary. Clean slip rings, and install new brushes if necessary (see Section 6-15). Disconnect leads 21, 23, and 33 from brushes, and check continuity across slip rings.
B. 50 Or 60 Hz Auxiliary Power Trouble Remedy No auxiliary power output at recep- Run engine at power/idle speed. tacles RC1, RC2, or RC3. Reset circuit breakers CB1 and CB2. Effective with Serial No. KE629034, also reset circuit breakers CB5 and CB7 (see Section 4-3). Check receptacles RC1, RC2, RC3 for continuity and proper connections. Replace receptacle(s) if necessary. Check connections to terminal strip 1T. Clean slip rings, and install new brushes if necessary (see Section 6-15).
D. Engine Trouble Engine will not start. Remedy Check fuel level (see Section 2-4). Check battery and engine charging system according to engine manual. Check continuity of Engine Control switch S2, and replace if necessary. See engine manual. Engine starts but stops as soon as En- Check oil level (see Section 2-4). Check low oil pressure shutdown switch S3 (see engine parts manual gine Control switch S2 returns to Run for location). S3 should close when engine is running. position.
6-2. Troubleshooting Circuit Diagram For Welding Generator Resistance Values a) Tolerance – ±10% unless specified b) Condition – 70°F (21°C); cold machine (no warm-up) c) Wiring Diagram – see Section 9 d) Stop engine before checking resistance R1 29 ohms R2 34 ohms R3 35 ohms R4 2 ohms R5 2 ohms R6 thru R17 Less than 1 ohm R18 Pull: Less than 1 ohm Hold: 16.
Amperage Readings a) Tolerance – ±5% unless specified b) Condition – 70°F (21°C); cold machine (no warm-up); no load I1 3 amps dc I2 1.8 amps dc (R1 at min.) 3.1 amps dc (R1 at max.
6-3.
Amperage Readings a) Tolerance – ±5% unless specified b) Condition – 70°F (21°C); cold machine (no warm-up); no load I1 3 amps dc I2 1.8 amps dc (R1 at min.) 3.1 amps dc (R1 at max.) Voltage Readings a) b) c) d) V7/ R4 V4 V2 AC/CC OCV, at weld rpm: 65 volts ac (R1 at min.) 80 volts ac (R1 at max.
6-4. Waveforms For Sections 6-2 And 6-3 2 ms 50 V 2 ms 10 V gnd gnd A. DC Open-Circuit Voltage, Ampere Ranges Switch S5 In Max Position B. DC Weld Output, 25 Volts DC, 100 Amperes, Ampere Range Switch S5 In 70-105 Position (Resistive Load) 5 ms 50 V 5 ms 20 V gnd gnd C. AC Open-Circuit Voltage, Ampere Ranges Switch S5 In Max Position D.
6-5. Idle Control Board/Module PC1 Testing Information Be sure plugs are secure before testing. See Section 6-6 for specific values during testing. 1 2 Idle Control Board PC1 (Prior To Serial No. JH300534) Idle Module PC1 (Effective With Serial No. JH300534) 1 OR 2 Test Equipment Needed: Ref.
6-6. Troubleshooting Flowcharts For Idle Control Board/Module PC1 Engine does not go to power/idle rpm with no weld load applied. Engine does not go to weld rpm with load applied. Connect meter (AC) between terminal G and terminal E. Connect meter (DC) between terminal B (+) and terminal E (–). Start engine. Place Engine Control switch S2 in Run/Idle position. Start engine. Place Engine Control switch S2 in Run/Idle position; Idle Lock switch S1 in Unlock position.
Engine does not go to weld rpm with Engine Control switch S2 in Run position. Control Relays CR3 and CR4 do not energize at idle rpm (See Section 5 for CR3 and CR4 information) Connect meter (DC) between terminal A (+) and F (–) prior to Serial No. JH300534, or B (+) and F (–) effective with Serial No. JH300534. Connect meter (DC) between terminals D (+) and E (–). Start engine. Place Engine Control switch S2 in Run position. Start engine. Place Engine Control switch in Run position.
6-7. Voltage Regulator Board PC2 Testing Information Prior To Serial No. KE604176 2 1 Be sure plugs are secure before testing. See Section 6-8 for specific values during testing. 1 2 Voltage Regulator Board PC2 Terminals A Thru G Test Equipment Needed: Ref. ST-800 698-A / SA-099 497-B 6-8. Voltage Regulator Board PC2 Test Point Values Prior To Serial No.
6-9. Voltage Regulator Board PC2 Testing Information Effective With Serial No. KE604176 1 Be sure plugs are secure before testing. See Section 6-10 for specific values during testing. 2 1 2 Voltage Regulator Board PC2 Receptacle RC1 Test Equipment Needed: Ref. ST-800 698-A / SA-160 889-A 6-10. Voltage Regulator Board PC2 Test Point Values Effective With Serial No.
6-11. Optional Remote Control Board PC3 Testing Information 1 Be sure plugs are secure before testing. See Section 6-12 for specific values during testing. 1 2 Remote Control Board PC3 Receptacle RC1 2 Test Equipment Needed: Ref. ST-800 698-A / ST-115 941-L / SA-138 247 6-12.
6-13. Optional Remote Capacitor Board PC5 Testing Information Effective With Serial No. KD346698 4 Be sure plugs are secure before testing. See Section 6-14 for specific values during testing. 3 1 2 3 4 Capacitor Board PC5 Remote 14 Receptacle RC1 Receptacle RC2 Terminal K 2 1 Test Equipment Needed: Ref. ST-800 698-A / SA-156 026-C 6-14. Optional Remote Capacitor Board PC5 Test Point Values Effective With Serial No.
6-15. Replacing Brushes And Cleaning Slip Rings A. Checking Brushes And Cleaning Slip Rings Stop engine and allow to cool. 1 Brush Holder Retaining Bar 2 Brush Holder Bracket Remove brush holder bracket. Keep hardware for reinstallation. 3 Brush Holder 4 Brush With Spring 5 Brush Holder Cap Mark and disconnect leads at caps, and remove brushes from bracket. Replace brushes if damaged, or if brush is at or near minimum length. 6 Slip Rings Inspect slip rings.
B. Adjusting Brush Position Stop engine. After installing brushes, adjust brush position as follows: 1 Brush Holder 2 Brass Sleeve 3 Brush 4 Slip Ring Loosen brush holder bracket mounting hardware. Move bracket until brass sleeves are positioned as shown. Tighten hardware. Reinstall side panels and cover. If operation is still not okay, have a qualified machine shop turn and polish slip rings. Side View 3/32 in (2.
6-16. Checking Unit Output After Servicing Check engine speeds, and adjust if necessary (see Section 8-5). 1 115 VAC 100 Hz Receptacle RC4 With no load applied and engine running at weld rpm, there should be 128 to 132 volts ac present at RC4. 2 Slider 3 Resistor R4 Y Stop engine before adjusting R4 If necessary, adjust slider on R4 until 128 to 132 volts ac is obtained at RC4. Do not exceed 132 volts ac. 4 DC Weld Output Terminals Turn Fine Amperage control R1 to max.
SECTION 7 – DISASSEMBLY AND REASSEMBLY 7-1. Disassembly Of Unit Use Section 6-1 to determine if trouble is in rotor, stator, engine or a combination of these components. Remove sheet metal panels from unit. Disconnect negative (–) battery cable from battery. Remove spark plugs. Mark and disconnect all stator leads. Y Do not damage rotor or stator during this procedure. Use hoist and lifting strap to remove the engine/generator assembly.
7-2. Disassembly Of Generator Hardware may differ from that shown. Torques: Prior To Serial No. KD523655 Effective With Serial No. KD523655 A 15 ft lb (20 N.m) A 15 ft lb (20 N.m) B 30 ft lb (41 N.m) B 20 ft lb (27 N.m) C 25 ft lb (34 N.m) C 25 ft lb (34 N.m) D 15 ft lb (20 N.m) D 20 ft lb (27 N.m) E 15 ft lb (20 N.m) E 15 ft lb (20 N.m) 5 A B C 6 D 7 8 4 3 9 2 10 1 11 12 16 E 15 14 13 ST-115 942-F Y Do not damage stator or rotor windings during this procedure.
SECTION 8 – MAINTENANCE 8-1. Routine Maintenance Y Stop engine before maintaining. Recycle engine fluids. . See also Engine Manual and mainte- nance label. Service engine more often during severe conditions. 8 Hours Wipe Up Spills OIL Full Check Fluid Levels. See Section 2-4 20 Hours Check And Clean Spark Arrestor Screen 25 Hours Clean And Check Air Cleaner 50 Hours Clean And Tighten Weld Terminals 100 Hours Change Oil. See Section 8-4 And Maintenance Label Change Oil Filter.
8-2. Maintenance Label ONAN P218 GAS ENGINE See Engine Manual for complete engine care. Give engine Specification and Serial Number when ordering parts. °C To Drain Oil: 30 +20 1/2 in. ID Hose +10 +40 Pull 0 10W Check daily. ° F +100 +30 Push And Turn CCW 5W-30 Recommended Oil . . . API Service Classification -10 SF, SG, SF/CC, SG/CE -20 0 Oil & Filter Change . . . . . . . . . . -30 dirty conditions . . . 25 hours or less normal conditions . 100 hours Oil Filter . . . . . . . . . . . .
8-3. Servicing Air Cleaner Y Do not run engine without air cleaner or with dirty element. 1 Stop engine. 1 2 Precleaner Wash precleaner with soap and water solution. Allow precleaner to air dry completely. Spread 1 tablespoon SAE 30 oil evenly into precleaner. Squeeze out excess oil. 2 Element Replace element if dirty or oily.
8-4. Changing Engine Oil, Oil Filter, And Fuel Filter Stop engine and allow to cool. 1 Oil Drain Valve 2 1/2 ID x 12 in Hose 3 Oil Filter Change engine oil and filter according to engine owner’s manual. Y Close valve and valve cap before adding oil and running engine. Fill crankcase with new oil to full mark on dipstick (see Section 8-2). Full 4 Fuel Filter 5 Fuel Line Replace line if cracked or worn. Install new filter. Wipe up any spilled fuel. Start engine, and check for fuel leaks.
8-5. Adjusting Engine Speed After tuning engine, check engine speeds with a tachometer. See table for proper no load speeds. If necessary, adjust speeds as follows: Start engine, and place Engine Control switch in Run/Idle position. Turn Fine Amperage control to 100. 1860 rpm (Power/Idle) 2 3000 rpm (Weld) 1 Carburetor 2 Throttle Solenoid Power/Idle Speed Adjustment 3 Power/Idle Speed Rod 4 Lock Nut 5 Adjustment Nut Loosen lock nut and rotate adjustment nut until engine runs at power/idle speed.
8-6. Overload Protection Stop engine. 1 Circuit Breaker CB4 (Internal – Not Shown) CB4 protects the unit from overload due to an obstructed throttle solenoid. If CB4 opens, engine speed drops to power/idle rpm for about 10 seconds before automatically resetting. If CB4 continues to open, check throttle solenoid TS1 and throttle linkage. 2 Fuse F1 (See Parts List For Rating) F1 protects the exciter excitation winding from overload. 2 Replace open fuse and reinstall panel before operating unit.
SECTION 9 – ELECTRICAL DIAGRAMS . The circuits in this manual can be used for troubleshooting, but there might be minor circuit differences from your machine. Use circuit inside machine case or contact factory for actual circuit, if needed. The following is a list of all diagrams for models covered by this manual. To order a copy, proceed as follows: 1 2 3 4 Know unit Model and Serial or Style Number. Use this list to find diagram number. Include your FAX number or mailing address with your request.
SC-114 477-A Figure 9-1. Circuit Diagram For Miller Legend Without Remote Control Effective With Serial No.
SC-168 053-A Figure 9-2. Circuit Diagram For Miller Legend Without Remote Control Effective With Serial No.
Coat terminals with dielectric grade, nonconductive, electric grease (MILLER Part No. 146 557) or equivalent. Figure 9-3. Wiring Diagram For Miller Legend Without Remote Control Effective With Serial No.
SD-168 051-B Miller Legend TM-428 Page 45
SC-115 947-A Figure 9-4. Circuit Diagram For Miller Legend With Remote Control Effective With Serial No.
SC-168 054-A Figure 9-5. Circuit Diagram For Miller Legend With Remote Control Effective With Serial No.
SB-113 710 Figure 9-6. Circuit Diagram For Idle Control Board PC1 Effective With Serial No. JH242114 Thru JH300533 SB-160 891 Figure 9-7. Circuit Diagram For Voltage Regulator Board PC2 Effective With Serial No.
OUTPUT POSITIVE SUPPLY+ SB-136 249 Figure 9-8. Circuit Diagram For Optional Remote Control Board PC3 Effective With Serial No. KA840710 And Following SB-148 024-A Figure 9-9. Circuit Diagram For HF Filter Board PC4 Effective With Serial No.
SB-156 027 Figure 9-10. Circuit Diagram For Optional Capacitor Board PC5 Effective With Serial No.
February 1996 Form: TM-428 Effective With Serial No.
TM-428 Page 52 Miller Legend 42 43 Figure 10-3 44 1 39 41 2 38 40 45 46 Figure 10-6 47 Figure 10-5 48 3 4 49 5 6 51 9 50 8 37 11 36 12 13 14 35 17 15 16 34 Figure 10-2 18 Figure 10-1.
Item No. Dia. Mkgs. Part No. Description Quantity Figure 10-1. Main Assembly . . . 1 . . . . . . . . . . . ++042 132 . . . REMOTE CONTROL, (Figure 10-6) (Prior to JK713332) . . . . . . . . . . . . . . . . . 1 . . . . . . . . . . . ++042 383 . . . REMOTE CONTROL, (Figure 10-6) (Eff w/JK713332) . . . . . . . . . . . . . . . . . . . 2 . . . . . . . . . . . Figure 10-5 . . . CONTROL PANEL, w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 . . . . . . . . . . . . . .
Item No. Dia. Mkgs. Part No. Description Quantity Figure 10-1. Main Assembly (Continued) . . . 27 . . . . . . . . . . . . . . 107 308 . . . HOLD DOWN, bat (Prior to KB113874) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 . . . . . . . . . . . . . . 146 697 . . . HOLD DOWN, bat (Eff w/KB113874 thru KF959176) . . . . . . . . . . . . . . . . . . . . 27 . . . . . . . . . . . . . . 165 631 . . . HOLD DOWN, bat (Eff w/KF959177 and on) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Item No. Dia. Mkgs. Part No. Description Quantity Figure 10-2. Generator (Figure 10-1 Item 34) . . . 1 . . . . . . . . . . . 013 367 . . . 2 . . . . . . . . . . . 115 500 . . . 2 . . . . . . . . . . . 134 092 . . . 2 . . . . . . . . . . . 176 891 . . . 3 . . . . . . . . . . +113 410 . . . 4 . . . . . . . . . . . 153 297 . . . 5 . . . . . . . . . . . 143 220 . . . 6 . . . . . . . . . . . 165 756 . . . 6 . . . . . . . . . . . 162 138 . . . 6 . . . . . . . . . . . 165 755 . . . 6 . . . . . . . . . . .
Item No. Dia. Mkgs. Part No. Description Quantity Figure 10-3. Panel, Front w/Components (Figure 10-1 Item 43) . . . 1 . . . RC1,2 . . . 604 176 . . . . . . . . . . . . . . . . . . . . . . . 073 690 . . . . . . 1 . . . RC1,2 . . . 167 657 . . . . . . 2 . . . CB1,2 . . . . 115 427 . . . . . . 2 . . . CB5,7 . . . . 168 057 . . . . . . 3 . . . . . . . . . . . . . . 113 315 . . . . . . 3 . . . . . . . . . . . . . . 130 352 . . . . . . 3 . . . . . . . . . . . . . . 143 383 . . . . . . 3 . . . . . . . . . .
Item No. Dia. Mkgs. Part No. Description Quantity Figure 10-3. Panel, Front w/Components (Figure 10-1 Item 43) (Continued) . . . . . . . . . . . . . . . . . . . . 039 273 . . . CONNECTOR, circ MS/MET 5 pin sz 16S MS-3106A-16S-8P Amphenol . . . . . . . . . . . . . . . . . . . . 039 685 . . . CONNECTOR, circ MS/MET clamp str rlf sz 16-16S AN-3057-8 Amphenol . . . 7 . . . . RC7 . ++086 022 . . . CONNECTOR, circ MS/MET 14skt sz 20 MS-3102A-20-27S (Eff w/JK713332 thru KD344393) . . . . . . . . . . . . . . .
Item No. Part No. Description 005 563 ... ... ... ... ... ... ... ... ... ... ... ... ... 1 ........ 2 ........ 3 ........ 4 ........ 5 ........ 6 ........ 7 ........ 8 ........ 9 ........ 10 . . . . . . . . 11 . . . . . . . . 12 . . . . . . . . 13 . . . . . . . . 005 562 005 561 005 564 605 276 005 559 005 560 008 485 005 566 011 644 052 405 052 404 005 557 005 558 Quantity Figure 10-4. Switch, Selector (Figure 10-3 Item 4) .. .. .. .. .. .. .. .. .. .. .. .. .. BRACKET, mtg-switch . . . . . . . .
Item No. Dia. Mkgs. Part No. Description Quantity Figure 10-5. Control Panel, w/Components (Figure 10-1 Item 2) . . . 1 . . . . . 1T . . . . . . . . 1 . . . . . 1T . . . . . ... 2 .............. ... 2 .............. ... 3 .............. . . . 4 . . . . PC2 . . . . . . . 4 . . . . PC2 . . . . . . . . . . . . . . PLG1 . . . . .................... . . . 5 . . . . CR4 . . . . . . . 6 . . . . CR3 . . . . . . . 7 . . . . CR2 . . . . . . . 8 . . . . CB4 . . . . . . . 9 . . . . PC1 . . . . . . . 9 . . . .
Item No. Dia. Mkgs. Part No. Description +042 132 +042 383 . . . 1 . . . . PC3 . . . . ... 2 .............. ... 3 .............. ... 3 .............. . . . 4 . . . . CR5 . . . . ... 5 .............. . . . 6 . . . . . C5 . . . . . . . . 7 . . . . . 2T . . . . . ... 8 .............. . . . 9 . . . . PLG6 . . . . .................... Quantity Figure 10-6. Remote Control, Option (Figure 10-1 Item 1) 136 246 . . . CIRCUIT CARD ASSEMBLY, remote control . . . . . . . . . . . . . . . . . . . . . . . .
Dia. Mkgs. Part No. PC2 160 888 . . . . . . A50 . . . . . . . 165 411 . . . . . . . C1 . . . . . . 003 530 . . . . . . C50 . . . . . . . 119 199 . . . . . . C51 . . . . . . 053 992 . . . . . . C52 . . . . . . 000 348 . . . . . . C53 . . . . . . 005 023 . . . . . . C54 . . . . . . 072 935 . . . . . . C55 . . . . . . 137 463 . . . . . . C56 . . . . . . . 072 113 . . . . . . C57 . . . . . . 028 292 . . . . . . D50 . . . . . . 028 351 . . . . . . D51 . . . . . . 049 641 . . . . . D52-54 . . . . 026 202 . .
Notes
Notes
