Fluid Head OPERATOR’S MANUAL 1090 1092 1093 1096 1098 Compassx 2 Compassx 6 Compassx 8 Compassx 10 Compassx 18 Fluid Fluid Fluid Fluid Fluid Head Head Head Head Head
Features and Controls Spare Camera Screws Platform Safety Release Lever CB PLUS Selector Tilt Lock Slide Lock Lever Counterbalance Selector Ring Tilt Drag Ring LED Button Handle Clamp Pan Lock Accessory Mounts Pan Drag Ring M10 Stud Ball Clamp Fig. 1 2 Fig.
Introduction Safety Instructions Thank you for purchasing the Compassx Fluid Head. The Compassx Fluid Head has been designed to suit a wide range of cameras, lenses and accessories as demanded by professional users. Please use this manual to familiarise yourself with the operation of the Compassx Fluid Head and observe these instructions to prevent any damage to your equipment.
Operating Instructions 2. Mounting Your Camera Platform 2.1 Remove the CAMERA PLATE by lifting the SAFETY RELEASE LEVER on the PLATFORM (SLIDE LOCK LEVER must be unwound (clockwise)) (Fig. 3a). Slide Lock Lever 2.2 Attach the CAMERA PLATE to the camera1 such that the Centre of Gravity (C of G)2 mark on the camera is approximately in the middle of the camera plate. Tilt Lock 2.3 Tighten PAN/TILT LOCKS, mount the CAMERA PLATE to the PLATFORM non-locking side first.
Operating Instructions 3. Counterbalance Control The counterbalance system was designed to neutralise the effect of the camera weight when it is tilted. The Compassx Fluid Head offers a 16 position counterbalance system which is operated with the CB SELECTOR RING and the CB PLUS SELECTOR (Fig. 4).
Operating Instructions 4. Pan/Tilt Drag Control The Compassx Fluid Head offers selectable positions of fluid drag in the Pan and Tilt (including zero positions). The settings are equally stepped from lighter drag in position 1 up to heavier drag in position 3 on CX2 and CX6 models and position 5 on CX8, CX10 and CX18 models, the drag plates are completely disengaged in position zero.
Maintenance The Compassx Fluid Head offers high quality surface coatings, dust and moisture seals. Miller recommends keeping the Fluid Head clean at all times by using soft brushes and lint free cloth to wipe over the surfaces. • Do not immerse the Fluid Head in any liquid. • Do not use stiff brushes, abrasives, harsh detergents and solvents. Battery Replacement The Compassx Fluid Head uses a single 11A type - 6 Volt battery for Illumination.
Specifications 1090 Compassx 2 1092 Compassx 6 1093 Compassx 8 1096 Compassx 10 1098 Compassx 18 Weight 2.3kg (5.1lbs) 2.3kg (5.1bs) 2.5kg (5.5lbs) 2.5kg (5.5lbs) 2.5kg (5.5lbs) Payload range 0-8kg (0-17.5lbs) 0-12kg (0-26.4lbs) 0-12kg (0-26.4lbs) 0-12kg (0-26.4lbs) 0-16kg (0-35.
Specifications 75mm CX2 CX6 CX8 9
Specifications 100mm CX10 CX18 10
Storage Service, Sales and Support The Compassx Fluid Head can be stored for extended periods; Miller recommends storage in a Miller case and the following: Miller Authorised Service Agents must carry out all service and repair work. Failure to observe this requirement may void warranty. • Clean the external surfaces. • Keep in a dry place away from direct sunlight. • Loosen off PAN & TILT LOCK. Spare Parts and Accessories ITEM ITEM NO.
millertripods.com MILLER CAMERA SUPPORT EQUIPMENT 30 Hotham Parade Artarmon, Sydney NSW 2064 Australia Tel: +61 2 9439 6377 Fax: +61 2 9438 2819 Email: sales@miller.com.
