ALPINE ELECTRIC FIREPLACE INSERT OWNER’S MANUAL 120V AC; 60 Hz; Maximum power 1500 Watts All electric. No wood or charcoal. No gas. No venting required.
WARNING Read and understand this entire owner’s manual, including all safety information, before plugging in or using this product. Failure to do so could result in fire, electric shock, or serious personal injury. CAUTION Keep this owner’s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product. IMPORTANT SAFETY INFORMATION! WARNING l Read all instructions before using this heater! l This heater is hot when in use.
l Use only the electric insert with included mantel. NEVER use a mantel from another maker. l NEVER use this electric fireplace insert unless it is properly installed in the correct mantel. l AVOID INJURY FROM TIPPING! Anchor the TV, or other items, to the wall with the anti-tip kits supplied by the manufacturer. l NEVER sit, stand, or climb on this electric fireplace. Doing so could cause the unit to tip over, resulting in serious personal injury or property damage.
l The power cord supplied with the heater has three prongs: two flat blades (live and neutral) and one round pin (ground). If a 3-slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure at right). [NOTE: Adapter NOT INCLUDED.] l SAVE THESE INSTRUCTIONS! PREPARATION This insert has front panel made of GLASS! ALWAYS use extreme caution when handling glass. Failure to do so could result in personal injury or property damage.
Fig. 2 Fig. 1 CR2032 NEVER dispose of batteries in fire. Failure to observe this precaution may result in an explosion. Dispose of batteries at your local hazardous material processing center. ALWAYS replace the battery in the remote control with the same type of battery. Failure to do so may result in personal injury or property damage. ALWAYS unplug this fireplace heater before assembly or cleaning, or before relocating. Failure to do so could result in electric shock, fire, or personal injury.
MOBILE PHONE CONTROL FUNCTIONS Step1. Scan below QR code and download the “Smart Life” app on your mobile phone. Step2. Open the Smart Life app and Log in. If you have existing account, log in directly. Or you need to log in with your WeChat / QQ account, or register follow below steps. 1. Click “Register” 2. Agree the Privacy Policy 3.
4. The verification code will be sent to your mobile phone or email box, check and enter the right code in 60 seconds, or it will need to be resent 5. Set the password. It should contain 6 to 20 characters, including letters and digits. Then you have registered successfully Step 3. Add Device 1. Make sure the room which your fireplace in has wi-fi 2. Make sure your mobile phone has connected the room’s wi-fi or hotspot 3. Click “Add Device 4. Choose “Small Home Appliance”, and choose “Heater” 5.
How to control the fireplace on the app. Power button: Press once to turn on the fireplace. Press again to turn off the fireplace. Heat Settings: 1. Click “Add Device Slide your finger to adjust the temperature from 60 F - 82 F. 2. Press the “level 1” button, the heater will start to operate, 750W (LOW HEAT) heater turns on and the fan starts to blow warm air. Press the “Level 2” Button 1,500W (HIGH HEAT) heater turns on and blows hot air. Press “off” button, the heater turns OFF.
Timer: Slide your finger to set the timer function from 0h to 8h. Control Panel, Heat Enabling Switch, and Remote Control Control Panel Remote Control Control Panel and Remote-Control Operation BUTTON ON/OFF FLAME TEMP OPERATION NOTES / INDICATONS Press the POWER button to turn the fireplace on and off. The POWER button turns the flame effect on and off The power must be turned ON for the control panel and remote control to work.
press to turn the heater on and off, then turn on or off the heating function. Note: The flame effect must be on for the heater to work The TIMER will turn the fireplace off after a certain amount of time. Press the TIMER button to select from the following settings: 00 (off), 1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H. Once at 8H, press the button again to return to 00 (off).
Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! ALWAYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. Electrical and Moving Parts: • The fan motors are lubricated at the factory and will not require lubrication. • Electrical components are integrated in the fireplace and are not serviceable by the consumer.
1. Make sure the battery is properly installed, and the plastic tab is removed. 2. Make sure the ON/OFF switch on the control panel is turned on. The remote control will not work unless the ON/OFF switch on the control panel is turned on. 3. Remove objects that may be in the way. Aim the remote control at the receiver in the center of the front panel. 4. Don’t press the remote-control buttons too quickly. Give the unit time to respond to your commands. Turn the heater off immediately.
LIMITED WARRANTY This warrants to the original purchaser that this product is free from defects in material and workmanship as of the date of purchase and that it will, under normal use and proper care, remain so for 1 year from the date of purchase. Missing or initially defective parts will be replaced free of charge during the period of this limited warranty. If parts are unavailable, comparable replacement or refund will be given. The original dated sales receipt is required for all warranty claims.
