Service Parts List S/N B30A

ManualsBrandsMilwaukee ManualsImpact Driver2401-20

RED

LEADWIRE

BLACK

LEADWIRE

NEGATIVE

TERMINAL

POSITIVE TERMINAL (NOT SHOWN)

12 13

14a 14b

14a

14b

See detail above

BULLETIN NO.

54-42-2400

SERVICE PARTS LIST

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

1 23-30-0095 Motor assembly (1)

2 44-66-0155 Motor mount plate (1)

3 05-81-0205 Screw (2)

4 14-29-0095 Gearcase assembly (1)

5 23-66-1095 Electronics module assembly (1)

6 06-82-2400 Screw (5)

7 06-82-2395 Screw (4)

8 42-70-0055 Housing Connection clip (1)

9 45-24-0095 Forward/reverse button (1)

10 12-20-2400 Service nameplate (1)

11 10-15-0955 Warning label (1)

12 10-20-0760 Fuel gauge label (1)

13 22-09-0075 Fuel gauge (1)

14 31-50-2400 Housing assembly (1)

14a --------------- Housing halve- left (1)

14b --------------- Housing halve- right (1)

15 --------------- Metal pin (2)

CATALOG NO. 2401-20

REVISED BULLETIN

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

M12™ Sub-Compact 1/4" Hex Driver

STARTING

SERIAL NO.

WIRING INSTRUCTION

B30A

SEE NOTES

DATE

Feb. 2014

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 W. Lisbon Road, Brookﬁ eld, WI 53005

Drwg. 6

NOTES:

1,2,4 IMPORTANT: See the back side of this bulletin if

servicing the motor assembly (1) or the gearcase

assembly (4).

3 Seating torque is to be 6-12 Kgf-cm (5-10.5 in-lbs)

5, 1 Solder red lead wire from electronics module assem-

bly (5) to positive terminal (red) of Motor Assembly.

Solder black lead wire from electronics module as-

sembly (5) to negative terminal of Motor Assembly.

5, 13 Insert the fuel gauge (13) wire assembly into the

electronics module assembly.

EXAMPLE:

Component Parts (Small #) Are Included

When Ordering The Assembly (Large #).

42-70-0058

Improved

Design

Original

Design

42-70-0055

M12™ tools utilize two different Housing

Connection Clip designs depending on the

Handle Set . See page two for details.

Summary of content (3 pages)

PAGE 1
BULLETIN NO. SERVICE PARTS LIST 54-42-2400 SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS M12™ Sub-Compact 1/4" Hex Driver CATALOG NO. 00 2401-20 EXAMPLE: 0 Component Parts (Small #) Are Included When Ordering The Assembly (Large #). STARTING SERIAL NO. REVISED BULLETIN DATE Feb. 2014 WIRING INSTRUCTION B30A SEE NOTES 42-70-0058 Improved Original Design Design 42-70-0055 M12™ tools utilize two different Housing Connection Clip designs depending on the Handle Set .
PAGE 2
Early M12™ Handle Sets utilize Housing Connection Clip No. 42-70-0055. Install this clip design by aligning the side rails of the clip with the two slots in the handle set. Gently push into place with the aid of a small flat blade screwdriver or a similar instrument. Be sure that the clip is properly seated in both slots and that the clip is flush to sub-flush to the end of the handle set.
PAGE 3
SUBJECT: 23-30-0095 MOTOR ASSEMBLY with NYLON or ALUMINUM Motor Mount Plate 14-29-0095 GEARCASE ASSEMBLY with NON-MACHINED or MACHINED Gearcase Motor Mount Plate of service replacement 23-30-0095 MOTOR ASSEMBLY can be either NYLON or ALUMINUM. When replacing either the 23-30-0095 MOTOR ASSEMBLY or 14-29-0095 GEARCASE ASSEMBLY the mating of the motor assembly with the gearcase is dependent on the original motor mount plate of 2401-20 Hex Driver being serviced.