Service Parts List

MILWAUKEE TOOL • www.milwaukeetool.com
13135 W. Lisbon Road, Brookeld, WI 53005
Drwg. 5
BULLETIN NO.
54-22-2400
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 06-82-1080 M3.0 x 14mm Pan Hd. ST T-10 Screw (11)
2 12-20-2426 Service Nameplate (1)
3 --------------- Housing Halve - Right (1)
4 06-82-2395 M2.6 x 10mm Pan Hd. ST T-9 Screw (1)
5 --------------- Motor (1)
6 --------------- Motor Pinion (1)
7 --------------- Mounting Plate (1)
8 --------------- M3.0 x 16mm Pan Hd. Screw (2)
9 --------------- Washer (2)
10 34-40-0620 O-Ring (2)
11 --------------- Spring Washer (2)
12 --------------- Spline Shaft (1)
13 --------------- Counter Balance (1)
14 --------------- Ball Bearing (1)
15 --------------- Retaining Ring (1)
16 --------------- Needle Roller Bearing (1)
17 06-65-0085 Pin (2)
18 --------------- Gearcase (1)
19 --------------- Needle Bearing (1)
20 --------------- Fork (1)
21 --------------- Ball Bearing (1)
22 --------------- Retaining Ring (1)
23 --------------- Output Shaft (1)
24 --------------- Bit Holder (1)
25 42-04-0730 Adapter (1)
26 42-92-1150 Blade Cover (1)
27 05-81-1400 M6 x 1 x 22.6 Flat Hd. Hex Recess Screw (1)
28 --------------- Housing Halve - Left (1)
29 45-72-0250 Switch Trigger (1)
30 --------------- Switch (1)
31 --------------- Leadwire Assembly - Red (Not Shown) (1)
32 --------------- Contact Plate Holder (1)
33 --------------- PCBA (1)
34 --------------- Fuel Gauge Label (Not Shown) (1)
35 42-70-0480 Spring Clip (1)
36 --------------- Ball Bearing (1)
37 44-52-1015 Rubber Pad - Right (1)
38 44-52-1010 Rubber Pad - Left (1)
40 42-52-0475 Gearcase Cover (1)
41 05-74-0900 M3.0 x 10mm Pan Hd. T-10 Screw (2)
44 42-55-2426 Canvas Carrying Case (1)
52 23-66-0915 Switch Assembly Kit (1)
53 14-29-0675 Gearcase Assembly Kit (1)
54 14-50-1020 Motor Assembly Kit (1)
55 31-44-2570 Housing Halve Assembly Kit (1)
CATALOG NO. 2426-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
12 VOLT MULTI-TOOL
STARTING
SERIAL NO.
DATE
Oct. 2019
WIRING INSTRUCTION
C73A
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
See Reverse Side
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
56 14-46-2426 Screw and Washer Kit (1)
57 42-87-0200 Counter Balance Assembly Kit (1)
60 43-44-1500 Dust Cap (1)
49-96-0500 Hex Key (Not Shown) (1)
10-20-2426 Warning Label (Not Shown) (1)
FIG. NOTES
1,4 Hand tighten housing screws to prevent over tightening. Exercise
caution when tightening screws if a cordless driver drill is used.
5,8 Apply Blue Loctite® 242 or equivalent, sparingly to the rst two
or three threads of screws (8) prior to assembling to motor (5).
Install spring clip (35)
into the left housing
halve (28) prior to
installing right
housing halve (3).
NOTE: Right
spring interlock
must match that of
the left housing
halve prior to
tightening housing
screws (1 and 4).
5
6
7
10
9
11
8
36
17
12
20
19
13
14
15
16
18
60
37
3
33
38
1
21
22
23
24
25
26
27
40
41
2
28
29
30
32
35
4(1x)
44
52
30 31
32 33
56
8 9
11
54
5
6
55
1 3 4 28
34 37 38
57
7 10 12 13
14 15 36
53
16 18 19 20
21 22 23 24
1(9x)
BACKING PAD
44-52-2000
PLUNGE CUT
WOOD BLADE
50-02-1025
ACCESSORIES
LUBRICATION NOTES:
Use Type 'J' Grease,
No. 49-08-4220
When servicing, remove 90-95%
of the existing grease prior to in-
stalling Type “J”. Original grease
maybe similar in color but not
compatible with “J”.
Apply a heavy coating of grease
to Motor Pinion (6) and Spline
Shaft (12). Approx. 0.5g
Place a heavy coating of grease
in and around the open Ball
Bearing (36). Approx. 1g
Fill back cavity of Gearcase (18)
with approx. 3.5g of grease.
To t a l o f 5 . 0 g ( . 1 7 o z . )
28
3
35
Interlock
Area
NOTE:
Production of this
model did not have
Dust Cap (60) on the
rear of the motor prior to
March 2016. It is recommended
when servicing this tool, to order
and install a new Dust Cap (43-44-
1500) on all early models.