OPERATOR'S MANUAL MANUEL de L'UTILISATEUR MANUAL del OPERADOR Cat. No. No de cat. 2446-20 M12 CORDLESS GREASE GUN PISTOLET GRAISSEUR SANS FIL M12 PISTOLA DE GRASA INALÁMBRICA M12 TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S MANUAL. AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN COMPRENDRE LE MANUEL DE L'UTILISATEUR. PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DEL OPERADOR.
GENERAL POWER TOOL SAFETY WARNINGS WARNING READ ALL SAFETY WARNINGS AND INSTRUCTIONS. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. • Prevent unintentional starting.
ASSEMBLY Inserting/Removing the Battery To remove the battery, push in the release buttons and pull the battery pack away from the tool. To insert the battery, slide the pack into the body of the tool. Make sure it latches securely into place. WARNING Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery.
LIMITED WARRANTY - USA AND CANADA Every MILWAUKEE power tool (including cordless product – tool, battery pack(s) & battery charger and Work Light – cordless flashlight) is warranted to the original purchaser only to be free from defects in material and workmanship.
•Débrancher la fiche de la prise d’alimentation et/ou la batterie de l’outil électrique avant d’effectuer des réglages, de changer d’accessoires ou de ranger l’outil. De telles mesures de sécurité préventive réduisent le risque de mettre l’outil en marche accidentellement. •Ranger les outils électriques inutilisés hors de la portée des enfants et ne pas laisser des personnes qui connaissent mal les outils électriques ou ces instructions utiliser ces outils.
4. Faire fonctionner la pompe du chargeur jusqu’à ce que la tige soit poussée d’environ 200 mm (8 po) hors du cylindre. 5. Tourner la poignée de la tige de manière à relâcher le piston. Presser la tige complètement dans le cylindre. 6. Amorcer le pistolet graisseur tel que décrit à la section intitulée « Amorçage du pistolet graisseur ». 8. Relâcher la tige de la fente de retenue et la presser complètement dans le cylindre. 9.
GARANTIE LIMITÉE - AUX ÉTATS-UNIS ET AU CANADA Chaque outil électrique MILWAUKEE (y compris les produits sans fil [outils, batteries, chargeurs de batterie, et les lampes de travail-lampes de poche sans fil]) est garanti à l’acheteur d’origine être exempt de vice du matériau et de fabrication.
ADVERTENCIAS DE SEGURIDAD GENERALES PARA LA HERRAMIENTA ELÉCTRICA ADVERTENCIA LEA TODAS LAS ADVERTENCIAS E INSTRUCCIONES DE SEGURIDAD. Si no sigue todas las advertencias e instrucciones, se pueden provocar una descarga eléctrica, un incendio o lesiones graves. Guarde todas las advertencias e instrucciones para consultarlas en el futuro.
Especificaciones Presión de Funcionamiento 517 barra 2446-20 12 7 500 psi * Usar baterías Milwaukee XC Cat. No. Volts cd Velocidad de flujo * Capacidad del cilindro 77 ml (2.6 oz)/min a 69 barra (1 000 psi) 473 ml (16 oz) a granel 429 ml (14,5 oz) a cartucho Simbología OPERACION ADVERTENCIA Para reducir el riesgo de lesiones, extraiga siempre la batería antes de acoplar o desacoplar accesorios. Utilice únicamente accesorios específicamente recomendados para esta herramienta.
MANTENIMIENTO ADVERTENCIA Para reducir el riesgo de una lesión, desconecte siempre la herramienta antes de darle cualquier mantenimiento. Nunca desarme la herramienta ni trate de hacer modificaciones en el sistema eléctrico de la misma. Acuda siempre a un Centro de Servicio MILWAUKEE para TODAS las reparaciones. ADVERTENCIA Para reducir el riesgo de una explosión, no queme nunca una batería, aun si está dañada, “muerta” o completamente descargada.
UNITED STATES - MILWAUKEE Service MILWAUKEE prides itself in producing a premium quality product that is NOTHING BUT HEAVY DUTY®. Your satisfaction with our products is very important to us! If you encounter any problems with the operation of this tool, or you would like to locate the factory Service/Sales Support Branch or authorized service station nearest you, please call... 1-800-SAWDUST (1.800.729.3878) Monday-Friday 7:00 AM - 6:30 PM Central Time or visit our website at www.milwaukeetool.