Service Parts List S/N E51D

1
2
3
4
5
2
1
57
9
22
24
19(2x)
11a
10
12
61
24
51
10
42
28(4x)
63
59
27
34
35
49
58
44
45
62
27 34
35 36
Torque to 260 in/lbs ±24 in/lbs
(300 kgf-cm ±27 kgf-cm)
56
2 3 4 5 6 9
10 11a 25 51 57
36
23
60
28 43 46 47
48 50 64
64 43 44 45
25
22
23
See page two for components
and installation of High Voltage
protection system
IMPORTANT NOTE: Gearcase end cap #25 is
LEFT HAND THREAD!
As an aid to assembly,
carefully lower the complete
front end of tool (gearcase /
impacting system) onto the
gearcase end cap. Gently
hand tighten front end
assembly onto gearcase
end cap. Be careful not
to cross-thread! Once
installed by hand, seat
gearcase end cap with a
good adjustable wrench
using light pressure.
Do not over tighten!
LEFT HAND THREAD
NOTE: Place anvil
spring (51) onto
anvil (11a) with
curled end
inserted in
slot of anvil
as shown.
Place ball (10)
in anvil slot in
front of spring.
51
50(7x)
47
46(2x)
37 38
NOTE: Components of the impacting
assembly (61) can drop out of the
gearcase (57). Care must be taken
to hold those elements in place
when assembling onto the
gearcase end cap (25).
MILWAUKEE ELECTRIC TOOL CORPORATION
13135 W. Lisbon Road, Brookfi eld, WI 53005
Drwg. 1
BULLETIN NO.
54-26-2483
SERVICE PARTS LIST
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
1 31-12-0575 Rubber Cap (1)
2 45-22-2653 Sleeve (1)
3 34-60-0725 Retaining Ring (1)
4 45-88-1880 Washer (1)
5 40-50-1470 Spring (1)
6 --------------- Anvil Bushing (Not Shown) (1)
9 45-88-2135 Plastic Washer (1)
10 02-02-0170 3.5mm Steel Ball (1)
11a 42-06-0720 1/4" Hex Anvil (1)
12 02-02-1300 5mm Steel Ball (1)
19 02-02-0180 4.7mm Steel Ball (2)
22 --------------- Ball Bearing (1)
23 --------------- Gearcase End Cap (1)
24 --------------- Ring Gear (1)
25 44-66-1065 Gearcase End Cap Assembly (1)
27 --------------- Stator Assembly (1)
28 45-30-0300 Rubber Slug (4)
34 --------------- PCBA (1)
35 --------------- On-Off Switch (1)
36 --------------- Terminal Block Assembly (1)
37 45-24-0810 Fwd/Rev Shuttle (1)
38 40-50-1135 Spring (1)
42 42-70-0058 Housing Connection Clip (1)
43 --------------- Left Handle Halve with Fuel Gauge (1)
44 42-70-0580 Belt Clip (1)
45 --------------- Belt Hook Screw (1)
46 06-82-1090 M3 x 7mm Pan Hd. Plastite Screw (2)
47 --------------- Right Handle Halve (1)
CATALOG NO. 2453-20
REVISED BULLETIN
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS
M12™ Brushless 1/4" Hex Impact Driver
STARTING
SERIAL NO.
DATE
Aug. 2014
WIRING INSTRUCTION
E51D
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
0
00
SEE PAGES 2 and 3
FIG. PART NO. DESCRIPTION OF PART NO. REQ.
48 12-20-2435 Service Nameplate (Not Shown) (1)
49 42-55-1060 Carrying Case (1)
50 06-82-7236 4-20 x 5/8" Pan Hd. Plastite T-10 Scr (7)
51 40-50-0012 Anvil Spring (1)
56 14-30-1170 Gearcase Assembly (1)
57 28-50-0920 Front Gearcase with Bushing (1)
58 42-70-0490 Belt Clip Assembly (1)
59 16-07-0420 Rotor Assembly (1)
60 31-44-2453 Handle Assembly (1)
61 14-30-1200 Impacting Assembly (1)
62 14-20-1525 Electronics Assembly (1)
63 23-66-2455 POP Switch (1)
64 10-20-2845 Spanish/French Warning Label (1)
70 23-94-2120 U-Shaped Stamping/Wire Kit (Page 2) (1)
FIG. LUBRICATION
(Type 'J' Grease, No. 49-08-4220):
10,11a Lightly coat front washer surface of anvil (11a) with grease,
place a dab in the ball slot of anvil.
24,61 Lightly coat the I.D. of the ring gear (24) and the center of
the planet gears of impacting assembly with grease.
57 Coat inside of bushing inside front gearcase with grease.
59 Coat pinion of rotor assembly (59) with grease.
54-26-2482

= Part number change
from previous service
parts list.