Product Manual

12
13
• Put a few rm strokes on every tooth. File all left
hand cutters in one direction. Then move to the other
side and le the right hand cutters in the opposite
direction. Occasionally remove lings from the le
with a wire brush.
Top Plate Filing Angle
CORRECT
Top Plate Filing Angle
More
than 30°
Less
than 30°
30°
INCORRECT
Top Plate Filing Angle
• CORRECT 30° - File holders are marked with guide
marks to align le properly to produce correct top
plate angle.
• LESS THAN 30° - For Cross Cutting.
• MORE THAN 30° - Feathered Edge Dulls Quickly.
Side Plate Angle
CORRECT
Side Plate
Filing Angle
Backward
Slope
Hook
80°
INCORRECT
Side Plate Filing Angle
• CORRECT - 80° Produced automatically if correct
diameter le is used in le holder.
• HOOK - “Grabs” and dulls quickly. Increases po-
tential of KICKBACK. Results from using a le with
diameter too small, or le held too low.
• BACKWARD SLOPE - Needs too much feed pres-
sure, causes excessive wear to bar and chain.
Results from using a le with diameter too large, or
le held too high.
Depth Gauge Clearance
• The depth gauge should be maintained at a clear-
ance of .025 in. Use a depth gauge tool for checking
the depth gauge clearances.
• Every time the chain is led, check the depth gauge
clearance.
Depth Gauge Jointer
Flat File
Use a at le and a depth gauge jointer to lower all
gauges uniformly. Depth gauge jointers are available
in .020 in. to .035 in. Use a .025 in. depth gauge
jointer. After lowering each
Restore
original
shape by
rounding
the front
depth gauge, restore original
shape by rounding the front.
Be careful not to damage
adjoining drive links with the
edge of the le.
Depth gauges must be ad-
justed with the at le in the
same direction the adjoin-
ing cutter was led with the
round le. Use care not to contact cutter face with
at le when adjusting depth gauges.
Guide Bar Maintenance
When the guide bar shows signs of wear, ip the
guide bar from bottom to top on the saw to distrib-
ute the wear for maximum bar life. The bar should
be cleaned every day of use and checked for wear
and damage.
Feathering or burring of the bar
Bar
Rails
rails is a normal process of
bar wear. Such faults should
be smoothed with a le as
soon as they occur.
A bar with any of the following
faults should be replaced.
• Wear inside the bar rails which permits the chain to
lay over sideways.
• Bent guide bar.
• Cracked or broken rails.
• Spread rails.
Lubricate guide bars with a sprocket at their tip
weekly. Using a grease syringe, lubricate weekly in
the lubricating hole. Turn the guide bar and check
that the lubrication holes and bar rails are free from
impurities.
NOTE: Do not replace the screw with an ordinary
screw. Use only identical replacement parts from the
manufacturer when replacing parts.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to ow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use ammable or
combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to the nearest authorized service center.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
SERVICE - UNITED STATES
1-800-SAWDUST (1.800.729.3878)
Monday-Friday, 7:00 AM - 6:30 PM CST
or visit www.milwaukeetool.com
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: [e-mail]
Become a Heavy Duty Club Member at
www.milwaukeetool.com to receive important
notications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE Outdoor Power Equipment Product* (see excep-
tions below) is warranted to the original purchaser only to be free from
defects in material and workmanship. Subject to certain exceptions,
MILWAUKEE will repair or replace any part on an outdoor power equip-
ment product which, after examination, is determined by MILWAUKEE
to be defective in material or workmanship for a period of three (3)
years after the date of purchase unless otherwise noted. Return of
the outdoor power equipment to a MILWAUKEE factory Service Center
location or participating MILWAUKEE Authorized Service Station,
freight prepaid and insured, is required. A copy of the proof of purchase
should be included with the return product. This warranty does not
apply to damage that MILWAUKEE determines to be from repairs
made or attempted by anyone other than MILWAUKEE authorized
personnel, misuse, alterations, abuse, normal wear and tear, lack of
maintenance, or accidents.
Normal Wear: Many outdoor power equipment products need periodic
parts replacement and service to achieve best performance. This war-
ranty does not cover repair when normal use has exhausted the life of
a part including, but not limited to trimmer head, trimmer head spool,
cutting lines, blades, chains, blower tubes, brushes, o-rings, and seals.
*This warranty does not cover Cordless Battery Packs or Recondi-
tioned Product. There are separate and distinct warranties available
for these products.
MILWAUKEE does not cover freight or labor charges associated with
the inspection and testing of outdoor power equipment products which
are found by MILWAUKEE not to be a valid warranty claim. A valid
warranty claim must be substantiated by the discovery of defective
material or workmanship by MILWAUKEE.
ACCEPTANCE OF THE EXCLUSIVE REPAIR AND REPLACEMENT
REMEDIES DESCRIBED HEREIN IS A CONDITION OF THE CON-
TRACT FOR THE PURCHASE OF EVERY MILWAUKEE PRODUCT.
IF YOU DO NOT AGREE TO THIS CONDITION, YOU SHOULD NOT
PURCHASE THE PRODUCT. IN NO EVENT SHALL MILWAUKEE
BE LIABLE FOR ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL
OR PUNITIVE DAMAGES, OR FOR ANY COSTS, ATTORNEY FEES,
EXPENSES, LOSSES OR DELAYS ALLEGED TO BE AS A CONSE-
QUENCE OF ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY
PRODUCT INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR
LOSS OF PROFITS. SOME STATES DO NOT ALLOW THE EX-
CLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT
APPLY TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU
OF ALL OTHER EXPRESS WARRANTIES, WRITTEN OR ORAL.
TO THE EXTENT PERMITTED BY LAW, MILWAUKEE DISCLAIMS
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW, SUCH IMPLIED WAR-
RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE
EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU, THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
This warranty applies to product sold in the U.S.A. and Canada only.
Please consult the ‘Service Center Search’ in the Parts & Service sec-
tion of MILWAUKEE’s website www.milwaukeetool.com or call 1.800.
SAWDUST (1.800.729.3878) to locate your nearest service facility for
warranty and non-warranty service on a Milwaukee electric power tool.
LIMITED WARRANTY - MEXICO,
CENTRAL AMERICA & CARIBBEAN
TECHTRONIC INDUSTRIES' warranty is for 3 years since the original
purchase date.
This warranty card covers any defect in material and workmanship
on this Product.
To make this warranty valid, present this warranty card, sealed/
stamped by the distributor or store where you purchased the product,
to the Authorized Service Center (ASC). Or, if this card has not been
sealed/stamped, present the original proof of purchase to the ASC.
Call 55 4160-3547 to nd the nearest ASC, for service, parts, acces-
sories or components.
Procedure to make this warranty valid
Take the product to the ASC, along with the warranty card sealed/
stamped by the distributor or store where you purchased the product,
and any faulty piece or component will be replaced without cost for
you. We will cover all freight costs relative with this warranty process.
Exceptions
This warranty is not valid in the following situations
a) When the product is used in a di󰀨erent manner from the end-user
guide or instruction manual.
b) When the conditions of use are not normal.
c) When the product was modied or repaired by people not authorized
by TECHTRONIC INDUSTRIES.
Note: If cord set is damaged, it should be replaced by an Authorized
Service Center to avoid electric risks.
SERVICE AND ATTENTION CENTER
Call to 55 4160-3547
IMPORTED AND COMMERCIALIZED BY
TECHTRONIC INDUSTRIES MEXICO, S.A. DE C.V.
Miguel de Cervantes Saavedra No.301 Piso 5, Torre Norte
11520 Colonia Ampliación Granada
Miguel Hidalgo, Ciudad de Mexico, Mexico
Model:
Date of Purchase:
Distributor or Store Stamp:
RÈGLES DE SÉCURITÉ GÉNÉRALES
RELATIVES AUX OUTILS ÉLECTRIQUES
AVERTISSEMENT
Lire toutes les consignes
de sécurité, consignes,
illustrations et spécications fournies avec cet
outil électrique. Ne pas suivre l’ensemble des règles
et instructions peut entraîner une électrocution, un
incendie ou des blessures graves. Conserver les
règles et les instructions à des ns de référence
ultérieure. Le terme «outil électrique» gurant dans
les avertissements ci-dessous renvoie à l’outil élec-
trique à alimentation par le réseau (à cordon) ou par
batterie (sans l).